[PATCH 3/3] ARM: dts: add Panel device support for exynos3250-rinato

[Inki Dae]

On 2014년 11월 28일 20:39, Inki Dae wrote:
> This patch adds MIPI-DSI and MIPI-DSI based S6E63J0X03 AMOLED panel
> device nodes for Exynos3250 Rinato board.

Hi Mr. Kukjin,

Please, ping~

Thanks,
Inki Dae

> 
> Signed-off-by: Inki Dae <inki.dae at samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park at samsung.com>
> ---
>  arch/arm/boot/dts/exynos3250-rinato.dts |   59 +++++++++++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
> index 79aa916..6e0e90d 100644
> --- a/arch/arm/boot/dts/exynos3250-rinato.dts
> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
> @@ -125,6 +125,65 @@
>  	};
>  };
>  
> +&dsi_0 {
> +	vddcore-supply = <&ldo6_reg>;
> +	vddio-supply = <&ldo6_reg>;
> +	samsung,pll-clock-frequency = <24000000>;
> +	status = "okay";
> +
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port at 1 {
> +			reg = <1>;
> +
> +			dsi_out: endpoint {
> +				remote-endpoint = <&dsi_in>;
> +				samsung,burst-clock-frequency = <250000000>;
> +				samsung,esc-clock-frequency = <20000000>;
> +			};
> +		};
> +	};
> +
> +	panel at 0 {
> +		compatible = "samsung,s6e63j0x03";
> +		reg = <0>;
> +		vdd3-supply = <&ldo16_reg>;
> +		vci-supply = <&ldo20_reg>;
> +		reset-gpios = <&gpe0 1 0>;
> +		te-gpios = <&gpx0 6 0>;
> +		power-on-delay= <30>;
> +		power-off-delay= <120>;
> +		reset-delay = <5>;
> +		init-delay = <100>;
> +		flip-horizontal;
> +		flip-vertical;
> +		panel-width-mm = <29>;
> +		panel-height-mm = <29>;
> +
> +		display-timings {
> +			timing-0 {
> +				clock-frequency = <0>;
> +				hactive = <320>;
> +				vactive = <320>;
> +				hfront-porch = <1>;
> +				hback-porch = <1>;
> +				hsync-len = <1>;
> +				vfront-porch = <150>;
> +				vback-porch = <1>;
> +				vsync-len = <2>;
> +			};
> +		};
> +
> +		port {
> +			dsi_in: endpoint {
> +				remote-endpoint = <&dsi_out>;
> +			};
> +		};
> +	};
> +};
> +
>  &fimd {
>  	status = "okay";
>  
>