[PATCH RFC v2 1/8] drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support

Neil Armstrong narmstrong at baylibre.com
Tue Dec 18 13:17:25 UTC 2018


On 18/12/2018 13:25, Andrzej Hajda wrote:
> Hi Neil,
> 
> 
> On 30.11.2018 14:42, Neil Armstrong wrote:
>> Add support for SCDC Setup for TMDS Clock > 3.4GHz and enable TMDS
>> Scrambling when supported or mandatory.
>>
>> This patch also adds an helper to setup the control bit to support
>> the high TMDS Bit Period/TMDS Clock-Period Ratio as required with
>> TMDS Clock > 3.4GHz for HDMI2.0 3840x2160 at 60/50 modes.
>>
>> These changes were based on work done by Huicong Xu <xhc at rock-chips.com>
>> and Nickey Yang <nickey.yang at rock-chips.com> to support HDMI2.0 modes
>> on the Rockchip 4.4 BSP kernel at [1]
>>
>> [1] https://github.com/rockchip-linux/kernel/tree/release-4.4
>>
>> Cc: Nickey Yang <nickey.yang at rock-chips.com>
>> Cc: Huicong Xu <xhc at rock-chips.com>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>> ---
>>  drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 88 ++++++++++++++++++++++-
>>  drivers/gpu/drm/bridge/synopsys/dw-hdmi.h |  1 +
>>  include/drm/bridge/dw_hdmi.h              |  1 +
>>  3 files changed, 87 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>> index 64c3cf027518..fcd941d52753 100644
>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>> @@ -28,6 +28,7 @@
>>  #include <drm/drm_crtc_helper.h>
>>  #include <drm/drm_edid.h>
>>  #include <drm/drm_encoder_slave.h>
>> +#include <drm/drm_scdc_helper.h>
>>  #include <drm/bridge/dw_hdmi.h>
>>  
>>  #include <uapi/linux/media-bus-format.h>
>> @@ -43,6 +44,11 @@
>>  
>>  #define HDMI_EDID_LEN		512
>>  
>> +/* DW-HDMI Controller >= 0x200a are at least compliant with SCDC version 1 */
>> +#define SCDC_MIN_SOURCE_VERSION	0x1
>> +
>> +#define HDMI14_MAX_TMDSCLK	340000000
>> +
>>  enum hdmi_datamap {
>>  	RGB444_8B = 0x01,
>>  	RGB444_10B = 0x03,
>> @@ -1015,6 +1021,33 @@ void dw_hdmi_phy_i2c_write(struct dw_hdmi *hdmi, unsigned short data,
>>  }
>>  EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_write);
>>  
>> +/*
>> + * HDMI2.0 Specifies the following procedure for High TMDS Bit Rates:
>> + * - The Source shall suspend transmission of the TMDS clock and data
>> + * - The Source shall write to the TMDS_Bit_Clock_Ratio bit to change it
>> + * from a 0 to a 1 or from a 1 to a 0
>> + * - The Source shall allow a minimum of 1 ms and a maximum of 100 ms from
>> + * the time the TMDS_Bit_Clock_Ratio bit is written until resuming
>> + * transmission of TMDS clock and data
>> + *
>> + * To respect the 100ms maximum delay, the dw_hdmi_set_high_tmds_clock_ratio()
>> + * helper should called right before enabling the TMDS Clock and Data in
>> + * the PHY configuration callback.
>> + */
>> +void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi)
>> +{
>> +	unsigned long mtmdsclock = hdmi->hdmi_data.video_mode.mpixelclock;
>> +
>> +	/* Control for TMDS Bit Period/TMDS Clock-Period Ratio */
>> +	if (hdmi->connector.display_info.hdmi.scdc.supported) {
>> +		if (mtmdsclock > HDMI14_MAX_TMDSCLK)
>> +			drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 1);
>> +		else
>> +			drm_scdc_set_high_tmds_clock_ratio(hdmi->ddc, 0);
>> +	}
>> +}
>> +EXPORT_SYMBOL_GPL(dw_hdmi_set_high_tmds_clock_ratio);
>> +
>>  static void dw_hdmi_phy_enable_powerdown(struct dw_hdmi *hdmi, bool enable)
>>  {
>>  	hdmi_mask_writeb(hdmi, !enable, HDMI_PHY_CONF0,
>> @@ -1216,6 +1249,8 @@ static int hdmi_phy_configure(struct dw_hdmi *hdmi)
>>  
>>  	dw_hdmi_phy_power_off(hdmi);
>>  
>> +	dw_hdmi_set_high_tmds_clock_ratio(hdmi);
>> +
>>  	/* Leave low power consumption mode by asserting SVSRET. */
>>  	if (phy->has_svsret)
>>  		dw_hdmi_phy_enable_svsret(hdmi, 1);
>> @@ -1237,6 +1272,10 @@ static int hdmi_phy_configure(struct dw_hdmi *hdmi)
>>  		return ret;
>>  	}
>>  
>> +	/* Wait for resuming transmission of TMDS clock and data */
>> +	if (mpixelclock > HDMI14_MAX_TMDSCLK)
>> +		msleep(100);
>> +
>>  	return dw_hdmi_phy_power_on(hdmi);
>>  }
>>  
>> @@ -1340,11 +1379,12 @@ static void hdmi_tx_hdcp_config(struct dw_hdmi *hdmi)
>>  
>>  static void hdmi_config_AVI(struct dw_hdmi *hdmi, struct drm_display_mode *mode)
>>  {
>> +	bool is_hdmi2_sink = hdmi->connector.display_info.hdmi.scdc.supported;
>>  	struct hdmi_avi_infoframe frame;
>>  	u8 val;
>>  
>>  	/* Initialise info frame from DRM mode */
>> -	drm_hdmi_avi_infoframe_from_display_mode(&frame, mode, false);
>> +	drm_hdmi_avi_infoframe_from_display_mode(&frame, mode, is_hdmi2_sink);
>>  
>>  	if (hdmi_bus_fmt_is_yuv444(hdmi->hdmi_data.enc_out_bus_format))
>>  		frame.colorspace = HDMI_COLORSPACE_YUV444;
>> @@ -1503,7 +1543,8 @@ static void hdmi_config_vendor_specific_infoframe(struct dw_hdmi *hdmi,
>>  static void hdmi_av_composer(struct dw_hdmi *hdmi,
>>  			     const struct drm_display_mode *mode)
>>  {
>> -	u8 inv_val;
>> +	u8 inv_val, bytes;
>> +	struct drm_hdmi_info *hdmi_info = &hdmi->connector.display_info.hdmi;
>>  	struct hdmi_vmode *vmode = &hdmi->hdmi_data.video_mode;
>>  	int hblank, vblank, h_de_hs, v_de_vs, hsync_len, vsync_len;
>>  	unsigned int vdisplay;
>> @@ -1513,7 +1554,9 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
>>  	dev_dbg(hdmi->dev, "final pixclk = %d\n", vmode->mpixelclock);
>>  
>>  	/* Set up HDMI_FC_INVIDCONF */
>> -	inv_val = (hdmi->hdmi_data.hdcp_enable ?
>> +	inv_val = (hdmi->hdmi_data.hdcp_enable ||
>> +		   vmode->mpixelclock > HDMI14_MAX_TMDSCLK ||
>> +		   hdmi_info->scdc.scrambling.low_rates ?
>>  		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_ACTIVE :
>>  		HDMI_FC_INVIDCONF_HDCP_KEEPOUT_INACTIVE);
>>  
>> @@ -1562,6 +1605,45 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
>>  		vsync_len /= 2;
>>  	}
>>  
>> +	/* Scrambling Control */
>> +	if (hdmi_info->scdc.supported) {
>> +		if (vmode->mpixelclock > HDMI14_MAX_TMDSCLK ||
>> +		    hdmi_info->scdc.scrambling.low_rates) {
>> +			/*
>> +			 * HDMI2.0 Specifies the following procedure:
>> +			 * After the Source Device has determined that
>> +			 * SCDC_Present is set (=1), the Source Device should
>> +			 * write the accurate Version of the Source Device
>> +			 * to the Source Version field in the SCDCS.
>> +			 * Source Devices compliant shall set the
>> +			 * Source Version = 1.
>> +			 */
>> +			drm_scdc_readb(&hdmi->i2c->adap, SCDC_SINK_VERSION,
>> +				       &bytes);
>> +			drm_scdc_writeb(&hdmi->i2c->adap, SCDC_SOURCE_VERSION,
>> +				min_t(u8, bytes, SCDC_MIN_SOURCE_VERSION));
>> +
>> +			/* Enabled Scrambling in the Sink */
>> +			drm_scdc_set_scrambling(&hdmi->i2c->adap, 1);
>> +
>> +			/*
>> +			 * To activate the scrambler feature, you must ensure
>> +			 * that the quasi-static configuration bit
>> +			 * fc_invidconf.HDCP_keepout is set at configuration
>> +			 * time, before the required mc_swrstzreq.tmdsswrst_req
>> +			 * reset request is issued.
>> +			 */
>> +			hdmi_writeb(hdmi, (u8)~HDMI_MC_SWRSTZ_TMDSSWRST_REQ,
> 
> 
> Are you sure you need casting to u8?

Not sure, it's already casted in dw_hdmi_clear_overflow() :

...
hdmi_writeb(hdmi, (u8)~HDMI_MC_SWRSTZ_TMDSSWRST_REQ, HDMI_MC_SWRSTZ);
...

I'll check if it's really needed.

> 
> 
>> +				    HDMI_MC_SWRSTZ);
>> +			hdmi_writeb(hdmi, 1, HDMI_FC_SCRAMBLER_CTRL);
>> +		} else {
>> +			hdmi_writeb(hdmi, 0, HDMI_FC_SCRAMBLER_CTRL);
>> +			hdmi_writeb(hdmi, (u8)~HDMI_MC_SWRSTZ_TMDSSWRST_REQ,
>> +				    HDMI_MC_SWRSTZ);
>> +			drm_scdc_set_scrambling(&hdmi->i2c->adap, 0);
>> +		}
>> +	}
>> +
>>  	/* Set up horizontal active pixel width */
>>  	hdmi_writeb(hdmi, mode->hdisplay >> 8, HDMI_FC_INHACTV1);
>>  	hdmi_writeb(hdmi, mode->hdisplay, HDMI_FC_INHACTV0);
>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
>> index 9d90eb9c46e5..3f3c616eba97 100644
>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
>> @@ -255,6 +255,7 @@
>>  #define HDMI_FC_MASK2                           0x10DA
>>  #define HDMI_FC_POL2                            0x10DB
>>  #define HDMI_FC_PRCONF                          0x10E0
>> +#define HDMI_FC_SCRAMBLER_CTRL                  0x10E1
>>  
>>  #define HDMI_FC_GMD_STAT                        0x1100
>>  #define HDMI_FC_GMD_EN                          0x1101
>> diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
>> index 9c56412bb2cf..7a02744ce0bc 100644
>> --- a/include/drm/bridge/dw_hdmi.h
>> +++ b/include/drm/bridge/dw_hdmi.h
>> @@ -157,6 +157,7 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense);
>>  void dw_hdmi_set_sample_rate(struct dw_hdmi *hdmi, unsigned int rate);
>>  void dw_hdmi_audio_enable(struct dw_hdmi *hdmi);
>>  void dw_hdmi_audio_disable(struct dw_hdmi *hdmi);
>> +void dw_hdmi_set_high_tmds_clock_ratio(struct dw_hdmi *hdmi);
>>  
>>  /* PHY configuration */
>>  void dw_hdmi_phy_i2c_set_addr(struct dw_hdmi *hdmi, u8 address);
> 
> Reviewed-by: Andrzej Hajda <a.hajda at samsung.com>

Thanks,
Neil

> 
>  --
> Regards
> Andrzej
> 
> 
> 



More information about the dri-devel mailing list