[Freedreno] [PATCH 03/11] drm/msm/dpu: use hsync/vsync polarity set by the encoder

[Jeykumar Sankaran]

On 4/19/2023 7:41 AM, Arnaud Vrac wrote:
> Do not override the hsync/vsync polarity passed by the encoder when
> setting up intf timings. The same logic was used in both the encoder and
> intf code to set the DP and DSI polarities, so those interfaces are not
> impacted. However for HDMI, the polarities were overriden to static
> values based on the vertical resolution, instead of using the actual
> mode polarities.
> 
Any idea why vres based static polarity override was in place? Hope you 
had tested HDMI resolutions with yres > and < than 720.

Jeykumar S.

> Signed-off-by: Arnaud Vrac <avrac at freebox.fr>
> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 16 +++-------------
>   1 file changed, 3 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 84ee2efa9c664..9f05417eb1213 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -104,7 +104,7 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
>   	u32 active_h_start, active_h_end;
>   	u32 active_v_start, active_v_end;
>   	u32 active_hctl, display_hctl, hsync_ctl;
> -	u32 polarity_ctl, den_polarity, hsync_polarity, vsync_polarity;
> +	u32 polarity_ctl, den_polarity;
>   	u32 panel_format;
>   	u32 intf_cfg, intf_cfg2 = 0;
>   	u32 display_data_hctl = 0, active_data_hctl = 0;
> @@ -191,19 +191,9 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
>   	}
>   
>   	den_polarity = 0;
> -	if (ctx->cap->type == INTF_HDMI) {
> -		hsync_polarity = p->yres >= 720 ? 0 : 1;
> -		vsync_polarity = p->yres >= 720 ? 0 : 1;
> -	} else if (ctx->cap->type == INTF_DP) {
> -		hsync_polarity = p->hsync_polarity;
> -		vsync_polarity = p->vsync_polarity;
> -	} else {
> -		hsync_polarity = 0;
> -		vsync_polarity = 0;
> -	}
>   	polarity_ctl = (den_polarity << 2) | /*  DEN Polarity  */
> -		(vsync_polarity << 1) | /* VSYNC Polarity */
> -		(hsync_polarity << 0);  /* HSYNC Polarity */
> +		(p->vsync_polarity << 1) | /* VSYNC Polarity */
> +		(p->hsync_polarity << 0);  /* HSYNC Polarity */
>   
>   	if (!DPU_FORMAT_IS_YUV(fmt))
>   		panel_format = (fmt->bits[C0_G_Y] |
>