[PATCH v3 1/6] drm/msm/dpu: fix video mode DSC for DSI

Dmitry Baryshkov dmitry.baryshkov at linaro.org
Wed Apr 3 09:57:44 UTC 2024


On Wed, 3 Apr 2024 at 12:11, Jun Nie <jun.nie at linaro.org> wrote:
>
> From: Jonathan Marek <jonathan at marek.ca>
>
> Add necessary DPU timing and control changes for DSC to work with DSI
> video mode.
>
> Signed-off-by: Jonathan Marek <jonathan at marek.ca>
> Signed-off-by: Jun Nie <jun.nie at linaro.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 9 +++++++++
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c          | 8 ++++++++
>  2 files changed, 17 insertions(+)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> index d9e7dbf0499c..c7b009a60b63 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> @@ -115,6 +115,15 @@ static void drm_mode_to_intf_timing_params(
>                 timing->h_front_porch = timing->h_front_porch >> 1;
>                 timing->hsync_pulse_width = timing->hsync_pulse_width >> 1;
>         }
> +
> +       /*
> +        * for DSI, if compression is enabled, then divide the horizonal active
> +        * timing parameters by compression ratio.
> +        */
> +       if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) {
> +               timing->width = timing->width / 3; /* XXX: don't assume 3:1 compression ratio */
> +               timing->xres = timing->width;
> +       }
>  }
>
>  static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing)
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 965692ef7892..079efb48db05 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -167,6 +167,14 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx,
>                 intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN;
>
>         data_width = p->width;
> +       if (p->wide_bus_en && !dp_intf)
> +               data_width = p->width >> 1;

How is wide_bus relevant to the DSC case?
Is there a need for the Fixes tag?

> +
> +       if (p->compression_en)
> +               intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS;
> +
> +       if (p->compression_en && dp_intf)
> +               DPU_ERROR("missing adjustments for DSC+DP\n");
>
>         hsync_data_start_x = hsync_start_x;
>         hsync_data_end_x =  hsync_start_x + data_width - 1;
>
> --
> 2.34.1
>


-- 
With best wishes
Dmitry


More information about the dri-devel mailing list