[Intel-gfx] [PATCH]DRM/IGD: Support IGD EOS - takes 2

Shaohua Li shaohua.li at intel.com
Fri Sep 4 07:09:23 CEST 2009


In the event that any one of the DAC analog outputs (R,G,B) were driven
at full-scale (white video) or some analog level close to full-scale
voltage, and if the video cable were then disconnected, the analog video
voltage level would exceed the maximum electrical overstress limit of the
native (thin-oxide) transistors thus causing a long-term reliability concern.
The electrical overstress condition occurs in this particular case.

This patch address the IGD EOS (electrical overstress condition) issue.
When the EOS interrupt occurs, OS should disable DAC and then disable EOS,
then the normal hotplug operation follows.

Signed-off-by: Shaohua Li <shaohua.li at intel.com>
---
 drivers/gpu/drm/i915/i915_drv.h  |    1 
 drivers/gpu/drm/i915/i915_irq.c  |   16 +++++++
 drivers/gpu/drm/i915/i915_reg.h  |    2 
 drivers/gpu/drm/i915/intel_crt.c |   83 ++++++++++++++++++++++++++++++++++++---
 drivers/gpu/drm/i915/intel_drv.h |    1 
 5 files changed, 96 insertions(+), 7 deletions(-)

Index: linux/drivers/gpu/drm/i915/i915_reg.h
===================================================================
--- linux.orig/drivers/gpu/drm/i915/i915_reg.h	2009-09-03 13:58:41.000000000 +0800
+++ linux/drivers/gpu/drm/i915/i915_reg.h	2009-09-03 14:01:10.000000000 +0800
@@ -683,6 +683,7 @@
 #define   SDVOB_HOTPLUG_INT_EN			(1 << 26)
 #define   SDVOC_HOTPLUG_INT_EN			(1 << 25)
 #define   TV_HOTPLUG_INT_EN			(1 << 18)
+#define   CRT_EOS_INT_EN			(1 << 10)
 #define   CRT_HOTPLUG_INT_EN			(1 << 9)
 #define   CRT_HOTPLUG_FORCE_DETECT		(1 << 3)
 #define CRT_HOTPLUG_ACTIVATION_PERIOD_32	(0 << 8)
@@ -717,6 +718,7 @@
 #define   DPC_HOTPLUG_INT_STATUS		(1 << 28)
 #define   HDMID_HOTPLUG_INT_STATUS		(1 << 27)
 #define   DPD_HOTPLUG_INT_STATUS		(1 << 27)
+#define   CRT_EOS_INT_STATUS			(1 << 12)
 #define   CRT_HOTPLUG_INT_STATUS		(1 << 11)
 #define   TV_HOTPLUG_INT_STATUS			(1 << 10)
 #define   CRT_HOTPLUG_MONITOR_MASK		(3 << 8)
Index: linux/drivers/gpu/drm/i915/i915_irq.c
===================================================================
--- linux.orig/drivers/gpu/drm/i915/i915_irq.c	2009-09-03 13:58:41.000000000 +0800
+++ linux/drivers/gpu/drm/i915/i915_irq.c	2009-09-03 14:01:10.000000000 +0800
@@ -237,6 +237,11 @@ static void i915_hotplug_work_func(struc
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_connector *connector;
 
+	intel_igd_handle_eos(dev, dev_priv->hotplug_status);
+
+	if (!(dev_priv->hotplug_status & dev_priv->hotplug_supported_mask))
+		return;
+
 	if (mode_config->num_connector) {
 		list_for_each_entry(connector, &mode_config->connector_list, head) {
 			struct intel_output *intel_output = to_intel_output(connector);
@@ -557,9 +562,11 @@ irqreturn_t i915_driver_irq_handler(DRM_
 		    (iir & I915_DISPLAY_PORT_INTERRUPT)) {
 			u32 hotplug_status = I915_READ(PORT_HOTPLUG_STAT);
 
+			dev_priv->hotplug_status = hotplug_status;
 			DRM_DEBUG("hotplug event received, stat 0x%08x\n",
 				  hotplug_status);
-			if (hotplug_status & dev_priv->hotplug_supported_mask)
+			if ((hotplug_status & dev_priv->hotplug_supported_mask) ||
+			   (IS_IGD(dev) && (hotplug_status & CRT_EOS_INT_STATUS)))
 				queue_work(dev_priv->wq,
 					   &dev_priv->hotplug_work);
 
@@ -960,6 +967,13 @@ int i915_driver_irq_postinstall(struct d
 		hotplug_en |= HOTPLUG_EN_MASK;
 		I915_WRITE(PORT_HOTPLUG_EN, hotplug_en);
 
+		/*
+		 * The pipe select needs to be 1 when CRT Hot plug Interrupt
+		 * Detection Enable is set when DAC is off under IGD
+		 */
+		if (IS_IGD(dev))
+			I915_WRITE(ADPA, I915_READ(ADPA) | ADPA_PIPE_B_SELECT);
+
 		dev_priv->hotplug_supported_mask = CRT_HOTPLUG_INT_STATUS |
 			TV_HOTPLUG_INT_STATUS | SDVOC_HOTPLUG_INT_STATUS |
 			SDVOB_HOTPLUG_INT_STATUS;
Index: linux/drivers/gpu/drm/i915/intel_crt.c
===================================================================
--- linux.orig/drivers/gpu/drm/i915/intel_crt.c	2009-09-03 13:58:41.000000000 +0800
+++ linux/drivers/gpu/drm/i915/intel_crt.c	2009-09-03 14:15:44.000000000 +0800
@@ -60,10 +60,45 @@ static void intel_crt_dpms(struct drm_en
 		break;
 	case DRM_MODE_DPMS_OFF:
 		temp |= ADPA_HSYNC_CNTL_DISABLE | ADPA_VSYNC_CNTL_DISABLE;
+
+		/*
+		 * The pipe select needs to be 1 when CRT Hot plug Interrupt
+		 * Detection Enable is set when DAC is off under IGD
+		 */
+		if (IS_IGD(dev))
+			temp |= ADPA_PIPE_B_SELECT;
 		break;
 	}
 
 	I915_WRITE(reg, temp);
+
+	if (IS_IGD(dev)) {
+		if (mode == DRM_MODE_DPMS_OFF) {
+			/* turn off DAC */
+			temp = I915_READ(PORT_HOTPLUG_EN);
+			temp &= ~CRT_EOS_INT_EN;
+			I915_WRITE(PORT_HOTPLUG_EN, temp);
+
+			temp = I915_READ(PORT_HOTPLUG_STAT);
+			if (temp & CRT_EOS_INT_STATUS)
+				I915_WRITE(PORT_HOTPLUG_STAT,
+					CRT_EOS_INT_STATUS);
+		} else {
+			/* turn on DAC. EOS interrupt must be enabled after DAC
+			 * is enabled, so it sounds not good to enable it in
+			 * i915_driver_irq_postinstall()
+			 * wait 12.5ms after DAC is enabled
+			 */
+			msleep(13);
+			temp = I915_READ(PORT_HOTPLUG_STAT);
+			if (temp & CRT_EOS_INT_STATUS)
+				I915_WRITE(PORT_HOTPLUG_STAT,
+					CRT_EOS_INT_STATUS);
+			temp = I915_READ(PORT_HOTPLUG_EN);
+			temp |= CRT_EOS_INT_EN;
+			I915_WRITE(PORT_HOTPLUG_EN, temp);
+		}
+	}
 }
 
 static int intel_crt_mode_valid(struct drm_connector *connector,
@@ -134,6 +169,7 @@ static void intel_crt_mode_set(struct dr
 	if (adjusted_mode->flags & DRM_MODE_FLAG_PVSYNC)
 		adpa |= ADPA_VSYNC_ACTIVE_HIGH;
 
+	adpa &= ~ADPA_PIPE_B_SELECT;
 	if (intel_crtc->pipe == 0) {
 		adpa |= ADPA_PIPE_A_SELECT;
 		if (!IS_IGDNG(dev))
@@ -147,9 +183,8 @@ static void intel_crt_mode_set(struct dr
 	I915_WRITE(adpa_reg, adpa);
 }
 
-static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector)
+static bool intel_igdng_crt_detect_hotplug(struct drm_device *dev)
 {
-	struct drm_device *dev = connector->dev;
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	u32 adpa, temp;
 	bool ret;
@@ -197,15 +232,14 @@ static bool intel_igdng_crt_detect_hotpl
  * \return true if CRT is connected.
  * \return false if CRT is disconnected.
  */
-static bool intel_crt_detect_hotplug(struct drm_connector *connector)
+static bool intel_crt_detect_hotplug(struct drm_device *dev)
 {
-	struct drm_device *dev = connector->dev;
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	u32 hotplug_en;
 	int i, tries = 0;
 
 	if (IS_IGDNG(dev))
-		return intel_igdng_crt_detect_hotplug(connector);
+		return intel_igdng_crt_detect_hotplug(dev);
 
 	/*
 	 * On 4 series desktop, CRT detect sequence need to be done twice
@@ -246,6 +280,43 @@ static bool intel_crt_detect_hotplug(str
 	return false;
 }
 
+void intel_igd_handle_eos(struct drm_device *dev, u32 hotplug_status)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 temp;
+	bool connected;
+
+	/* EOS interrupts occurs */
+	if (IS_IGD(dev) && (hotplug_status & CRT_EOS_INT_STATUS)) {
+
+		mutex_lock(&dev->mode_config.mutex);
+		connected = intel_crt_detect_hotplug(dev);
+		DRM_DEBUG("EOS interrupt occurs, VGA is %s\n",
+			connected ? "connected":"disconnected");
+
+		temp = I915_READ(PORT_HOTPLUG_STAT);
+		if (temp & CRT_EOS_INT_STATUS)
+			I915_WRITE(PORT_HOTPLUG_STAT, CRT_EOS_INT_STATUS);
+		if (connected) {
+			mutex_unlock(&dev->mode_config.mutex);
+			return;
+		}
+
+		temp = I915_READ(ADPA);
+		temp &= ~ADPA_DAC_ENABLE;
+		I915_WRITE(ADPA, temp);
+
+		temp = I915_READ(PORT_HOTPLUG_EN);
+		temp &= ~CRT_EOS_INT_EN;
+		I915_WRITE(PORT_HOTPLUG_EN, temp);
+
+		temp = I915_READ(PORT_HOTPLUG_STAT);
+		if (temp & CRT_EOS_INT_STATUS)
+			I915_WRITE(PORT_HOTPLUG_STAT, CRT_EOS_INT_STATUS);
+		mutex_unlock(&dev->mode_config.mutex);
+	}
+}
+
 static bool intel_crt_detect_ddc(struct drm_connector *connector)
 {
 	struct intel_output *intel_output = to_intel_output(connector);
@@ -395,7 +466,7 @@ static enum drm_connector_status intel_c
 	enum drm_connector_status status;
 
 	if (IS_I9XX(dev) && !IS_I915G(dev) && !IS_I915GM(dev)) {
-		if (intel_crt_detect_hotplug(connector))
+		if (intel_crt_detect_hotplug(dev))
 			return connector_status_connected;
 		else
 			return connector_status_disconnected;
Index: linux/drivers/gpu/drm/i915/intel_drv.h
===================================================================
--- linux.orig/drivers/gpu/drm/i915/intel_drv.h	2009-09-03 13:58:41.000000000 +0800
+++ linux/drivers/gpu/drm/i915/intel_drv.h	2009-09-03 14:01:10.000000000 +0800
@@ -177,4 +177,5 @@ extern int intel_framebuffer_create(stru
 				    struct drm_mode_fb_cmd *mode_cmd,
 				    struct drm_framebuffer **fb,
 				    struct drm_gem_object *obj);
+extern void intel_igd_handle_eos(struct drm_device *dev, u32 hotplug_status);
 #endif /* __INTEL_DRV_H__ */
Index: linux/drivers/gpu/drm/i915/i915_drv.h
===================================================================
--- linux.orig/drivers/gpu/drm/i915/i915_drv.h	2009-09-03 13:58:41.000000000 +0800
+++ linux/drivers/gpu/drm/i915/i915_drv.h	2009-09-03 14:01:10.000000000 +0800
@@ -190,6 +190,7 @@ typedef struct drm_i915_private {
 	u32 de_irq_enable_reg;
 
 	u32 hotplug_supported_mask;
+	u32 hotplug_status;
 	struct work_struct hotplug_work;
 
 	int tex_lru_log_granularity;



More information about the Intel-gfx mailing list