[Intel-gfx] Dell XPS 8700 kms not working
Paulo Zanoni
przanoni at gmail.com
Mon Jan 13 14:53:18 CET 2014
2014/1/12 Daniel Vetter <daniel at ffwll.ch>:
> On Sun, Jan 12, 2014 at 9:23 PM, Giacomo Comes <comes at naic.edu> wrote:
>> This is the dmesg output using drm-intel-next-2014-01-10
>>
>> I booted without loading the i915 module, started netconsole
>> and then insmod i915.ko. The computer freeze, the monitor goes in powersave
>> mode and after 45 seconds it powers off and then restarts.
>>
>> Any help?
>
> A hsw that dies when we should be doing the first modeset. This is one
> for Paulo.
I think you should report a bug on http://bugs.freedesktop.org.
Email-reported bugs tend to get forgotten quickly. Please reply with a
link to your bug report :)
That said, are you passing any special Kernel command line parameters?
The logs suggest you have an HDMI monitor connected, but later we try
to set a mode on the disconnected VGA monitor and on the HDMI monitor.
Does that reflect your setup?
Thanks,
Paulo
> -Daniel
>
>
>> [ 87.565651] netpoll: netconsole: local port 12345
>> [ 87.566075] netpoll: netconsole: local IPv4 address 0.0.0.0
>> [ 87.566576] netpoll: netconsole: interface 'enp3s0'
>> [ 87.566988] netpoll: netconsole: remote port 6666
>> [ 87.567384] netpoll: netconsole: remote IPv4 address 192.168.15.100
>> [ 87.567913] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
>> [ 87.568494] netpoll: netconsole: local IP 192.168.15.108
>> [ 87.568967] console [netcon0] enabled
>> [ 87.569282] netconsole: network logging started
>> [ 99.847801] [drm:i915_dump_device_info], i915 device info: gen=7, pciid=0x0412 flags=need_gfx_hws,is_haswell,has_fbc,has_hotplug,has_llc,has_ddi,has_fpga_dbg,
>> [ 99.849166] [drm:intel_detect_pch], Found LynxPoint PCH
>> [ 99.849789] [drm] Memory usable by graphics device = 2048M
>> [ 99.850254] [drm:i915_gem_gtt_init], GMADR size = 256M
>> [ 99.850696] [drm:i915_gem_gtt_init], GTT stolen size = 32M
>> [ 99.851162] checking generic (e0000000 500000) vs hw (e0000000 10000000)
>> [ 99.851730] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
>> [ 99.852447] Console: switching to colour dummy device 80x25
>> [ 99.870683] [drm:intel_opregion_setup], graphic opregion physical addr: 0xdb9cd018
>> [ 99.870694] [drm:intel_opregion_setup], Public ACPI methods supported
>> [ 99.870696] [drm:intel_opregion_setup], SWSCI supported
>> [ 99.894443] [drm:swsci_setup], SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
>> [ 99.894453] [drm:intel_opregion_setup], ASLE supported
>> [ 99.894516] i915 0000:00:02.0: irq 51 for MSI/MSI-X
>> [ 99.894527] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
>> [ 99.894529] [drm] Driver supports precise vblank timestamp query.
>> [ 99.894531] [drm:init_vbt_defaults], Set default to SSC at 120000 kHz
>> [ 99.894534] [drm:intel_parse_bios], Using VBT from OpRegion: $VBT HASWELL d
>> [ 99.894536] [drm:parse_general_features], BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
>> [ 99.894539] [drm:parse_general_definitions], crt_ddc_bus_pin: 2
>> [ 99.894543] [drm:parse_lfp_panel_data], Found panel mode in BIOS VBT tables:
>> [ 99.894546] [drm:drm_mode_debug_printmodeline], Modeline 0:"1024x768" 0 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
>> [ 99.894548] [drm:parse_lfp_panel_data], VBT initial LVDS value 300
>> [ 99.894551] [drm:parse_lfp_backlight], VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255
>> [ 99.894553] [drm:parse_sdvo_panel_data], Found SDVO panel mode in BIOS VBT tables:
>> [ 99.894557] [drm:drm_mode_debug_printmodeline], Modeline 0:"1600x1200" 0 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x8 0xa
>> [ 99.894559] [drm:parse_sdvo_device_mapping], No SDVO device info is found in VBT
>> [ 99.894562] [drm:parse_mipi], No MIPI BDB found
>> [ 99.894564] [drm:parse_ddi_port], Port B VBT info: DP:1 HDMI:1 DVI:1 EDP:0 CRT:0
>> [ 99.894567] [drm:parse_ddi_port], VBT HDMI level shift for port B: 6
>> [ 99.894569] [drm:parse_ddi_port], Port C VBT info: DP:0 HDMI:1 DVI:1 EDP:0 CRT:0
>> [ 99.894571] [drm:parse_ddi_port], VBT HDMI level shift for port C: 6
>> [ 99.894579] [drm:intel_dsm_pci_probe], no _DSM method for intel device
>> [ 99.894585] [drm:i915_gem_init_stolen], found 33554432 bytes of stolen memory at dd200000
>> [ 99.894614] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
>> [ 99.894621] [drm:intel_print_wm_latency], Primary WM0 latency 20 (2.0 usec)
>> [ 99.894623] [drm:intel_print_wm_latency], Primary WM1 latency 4 (2.0 usec)
>> [ 99.894625] [drm:intel_print_wm_latency], Primary WM2 latency 36 (18.0 usec)
>> [ 99.894627] [drm:intel_print_wm_latency], Primary WM3 latency 90 (45.0 usec)
>> [ 99.894630] [drm:intel_print_wm_latency], Primary WM4 latency 160 (80.0 usec)
>> [ 99.894632] [drm:intel_print_wm_latency], Sprite WM0 latency 20 (2.0 usec)
>> [ 99.894634] [drm:intel_print_wm_latency], Sprite WM1 latency 4 (2.0 usec)
>> [ 100.190535] [drm:i915_gem_setup_global_gtt], clearing unused GTT space: [0, 7ffff000]
>> [ 100.191674] [drm:gen6_ppgtt_init], Allocated pde space (2M) at GTT entry: 0
>> [ 100.191692] [drm:i915_gem_context_init], HW context support initialized
>> [ 100.191699] [drm:init_status_page], render ring hws offset: 0x00211000
>> [ 100.198614] [drm:init_pipe_control], render ring pipe control offset: 0x00232000
>> [ 100.198621] [drm:init_status_page], bsd ring hws offset: 0x00233000
>> [ 100.198667] [drm:init_status_page], blitter ring hws offset: 0x00254000
>> [ 100.198709] [drm:init_status_page], video enhancement ring hws offset: 0x00275000
>> [ 100.198814] [drm:intel_crt_reset], pch crt adpa set to 0xf40000
>> [ 100.198819] [drm:intel_modeset_readout_hw_state], [CRTC:3] hw state readout: enabled
>> [ 100.198821] [drm:intel_modeset_readout_hw_state], [CRTC:5] hw state readout: disabled
>> [ 100.198824] [drm:intel_modeset_readout_hw_state], [CRTC:7] hw state readout: disabled
>> [ 100.198826] [drm:intel_ddi_get_crtc_pll], Pipe A connected to port C using clock 0x80000000
>> [ 100.198829] [drm:intel_modeset_readout_hw_state], [ENCODER:10:DAC-10] hw state readout: disabled, pipe A
>> [ 100.198832] [drm:intel_modeset_readout_hw_state], [ENCODER:11:TMDS-11] hw state readout: disabled, pipe A
>> [ 100.198834] [drm:intel_modeset_readout_hw_state], [ENCODER:16:TMDS-16] hw state readout: enabled, pipe A
>> [ 100.198836] [drm:intel_modeset_readout_hw_state], [CONNECTOR:9:VGA-1] hw state readout: disabled
>> [ 100.198839] [drm:intel_modeset_readout_hw_state], [CONNECTOR:12:DP-1] hw state readout: disabled
>> [ 100.198841] [drm:intel_modeset_readout_hw_state], [CONNECTOR:15:HDMI-A-1] hw state readout: disabled
>> [ 100.198843] [drm:intel_modeset_readout_hw_state], [CONNECTOR:17:HDMI-A-2] hw state readout: enabled
>> [ 100.198846] [drm:intel_dump_pipe_config], [CRTC:3][setup_hw_state] config for pipe A
>> [ 100.198848] [drm:intel_dump_pipe_config], cpu_transcoder: A
>> [ 100.198850] [drm:intel_dump_pipe_config], pipe bpp: 24, dithering: 0
>> [ 100.198852] [drm:intel_dump_pipe_config], fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
>> [ 100.198854] [drm:intel_dump_pipe_config], dp: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
>> [ 100.198856] [drm:intel_dump_pipe_config], requested mode:
>> [ 100.198859] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 1280 0 0 0 1024 0 0 0 0x0 0x0
>> [ 100.198860] [drm:intel_dump_pipe_config], adjusted mode:
>> [ 100.198862] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x5
>> [ 100.198864] [drm:intel_dump_crtc_timings], crtc timings: 0 1280 1328 1440 1688 1024 1025 1028 1066, type: 0x0 flags: 0x5
>> [ 100.198866] [drm:intel_dump_pipe_config], port clock: 0
>> [ 100.198868] [drm:intel_dump_pipe_config], pipe src size: 1280x1024
>> [ 100.198870] [drm:intel_dump_pipe_config], gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000
>> [ 100.198872] [drm:intel_dump_pipe_config], pch pfit: pos: 0x00000000, size: 0x05000400, enabled
>> [ 100.198874] [drm:intel_dump_pipe_config], ips: 0
>> [ 100.214579] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0x3f40000, result 1
>> [ 100.312556] [drm:drm_edid_to_eld], ELD: no CEA Extension found
>> [ 100.312569] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:17:HDMI-A-2] probed modes :
>> [ 100.312573] [drm:drm_mode_debug_printmodeline], Modeline 24:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x48 0x5
>> [ 100.312576] [drm:drm_mode_debug_printmodeline], Modeline 30:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
>> [ 100.312579] [drm:drm_mode_debug_printmodeline], Modeline 25:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
>> [ 100.312582] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 75 78800 1024 1040 1136 1312 768 769 772 800 0x40 0x5
>> [ 100.312584] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
>> [ 100.312588] [drm:drm_mode_debug_printmodeline], Modeline 33:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
>> [ 100.312590] [drm:drm_mode_debug_printmodeline], Modeline 26:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
>> [ 100.312593] [drm:drm_mode_debug_printmodeline], Modeline 27:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
>> [ 100.312596] [drm:drm_mode_debug_printmodeline], Modeline 28:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
>> [ 100.312599] [drm:drm_mode_debug_printmodeline], Modeline 29:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
>> [ 100.312602] [drm:drm_setup_crtcs],
>> [ 100.312604] [drm:drm_enable_connectors], connector 9 enabled? yes
>> [ 100.312606] [drm:drm_enable_connectors], connector 12 enabled? no
>> [ 100.312608] [drm:drm_enable_connectors], connector 15 enabled? no
>> [ 100.312610] [drm:drm_enable_connectors], connector 17 enabled? yes
>> [ 100.312612] [drm:drm_target_preferred], looking for cmdline mode on connector 9
>> [ 100.312614] [drm:drm_target_preferred], looking for preferred mode on connector 9
>> [ 100.312617] [drm:drm_target_preferred], found mode 1024x768
>> [ 100.312619] [drm:drm_target_preferred], looking for cmdline mode on connector 17
>> [ 100.312621] [drm:drm_target_preferred], looking for preferred mode on connector 17
>> [ 100.312623] [drm:drm_target_preferred], found mode 1280x1024
>> [ 100.312625] [drm:drm_setup_crtcs], picking CRTCs for 8192x8192 config
>> [ 100.312629] [drm:drm_setup_crtcs], desired mode 1024x768 set on crtc 3
>> [ 100.312631] [drm:drm_setup_crtcs], desired mode 1280x1024 set on crtc 5
>> [ 100.312634] [drm:intelfb_create], no BIOS fb, allocating a new one
>> [ 100.312636] [drm:i915_gem_object_create_stolen], creating stolen object: size=500000
>> [ 100.312642] [drm:i915_pages_create_for_stolen], offset=0x0, size=5242880
>> [ 100.313331] [drm:intelfb_create], allocated 1280x1024 fb: 0x00296000, bo ffff880408d67e40
>> _______________________________________________
>> Intel-gfx mailing list
>> Intel-gfx at lists.freedesktop.org
>> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
>
>
> --
> Daniel Vetter
> Software Engineer, Intel Corporation
> +41 (0) 79 365 57 48 - http://blog.ffwll.ch
--
Paulo Zanoni
More information about the Intel-gfx
mailing list