[Intel-gfx] [PATCH 3/3] drm/i915/bxt: WA for swapped HPD pins in A stepping

Sivakumar Thulasimani sivakumar.thulasimani at intel.com
Sun Aug 9 22:28:55 PDT 2015


Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani at intel.com>

On 8/10/2015 10:35 AM, Sonika Jindal wrote:
> WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
> DDIA HPD pin in place of DDIB.
>
> v2: For DP, irq_port is used to determine the encoder instead of
> hpd_pin and removing the edp HPD logic because port A HPD is not
> present(Imre)
> v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
> Added hpd_pin swapping for intel_dp_init_connector, setting encoder
> for PORT_A as per the WA in irq_port (Imre)
> v4: Dont enable interrupt for edp, also reframe the description (Siva)
> v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
> instead avoid setting hpd_pin itself (Imre)
>
> Signed-off-by: Sonika Jindal <sonika.jindal at intel.com>
> ---
>   drivers/gpu/drm/i915/intel_ddi.c  |   10 +++++++++-
>   drivers/gpu/drm/i915/intel_dp.c   |    2 ++
>   drivers/gpu/drm/i915/intel_hdmi.c |    9 ++++++++-
>   3 files changed, 19 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index e2c6f73..777e3a3 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -3225,7 +3225,15 @@ void intel_ddi_init(struct drm_device *dev, enum port port)
>   			goto err;
>   
>   		intel_dig_port->hpd_pulse = intel_dp_hpd_pulse;
> -		dev_priv->hotplug.irq_port[port] = intel_dig_port;
> +		/*
> +		 * On BXT A0/A1, sw needs to activate DDIA HPD logic and
> +		 * interrupts to check the external panel connection.
> +		 */
> +		if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0)
> +					 && port == PORT_B)
> +			dev_priv->hotplug.irq_port[PORT_A] = intel_dig_port;
> +		else
> +			dev_priv->hotplug.irq_port[port] = intel_dig_port;
>   	}
>   
>   	/* In theory we don't need the encoder->type check, but leave it just in
> diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
> index 5a614c9..7fab3e5 100644
> --- a/drivers/gpu/drm/i915/intel_dp.c
> +++ b/drivers/gpu/drm/i915/intel_dp.c
> @@ -5788,6 +5788,8 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,
>   		break;
>   	case PORT_B:
>   		intel_encoder->hpd_pin = HPD_PORT_B;
> +		if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
> +			intel_encoder->hpd_pin = HPD_PORT_A;
>   		break;
>   	case PORT_C:
>   		intel_encoder->hpd_pin = HPD_PORT_C;
> diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
> index 70bad5b..94fa716 100644
> --- a/drivers/gpu/drm/i915/intel_hdmi.c
> +++ b/drivers/gpu/drm/i915/intel_hdmi.c
> @@ -1973,7 +1973,14 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
>   			intel_hdmi->ddc_bus = GMBUS_PIN_1_BXT;
>   		else
>   			intel_hdmi->ddc_bus = GMBUS_PIN_DPB;
> -		intel_encoder->hpd_pin = HPD_PORT_B;
> +		/*
> +		 * On BXT A0/A1, sw needs to activate DDIA HPD logic and
> +		 * interrupts to check the external panel connection.
> +		 */
> +		if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
> +			intel_encoder->hpd_pin = HPD_PORT_A;
> +		else
> +			intel_encoder->hpd_pin = HPD_PORT_B;
>   		break;
>   	case PORT_C:
>   		if (IS_BROXTON(dev_priv))

-- 
regards,
Sivakumar



More information about the Intel-gfx mailing list