<div dir="ltr"><div><div><div>Hi David,<br><br></div>I'm glad that it is working for you without the FCC Auth command!  However I am not able to replicate this behavior.  I suppose it is possible that you have some update that I do not, but it is also possible that the firmware is slightly different for some reason.  I'm not an expert!<br><br></div>When I have a little more time, I need to test this more, plus finish my QMI-over-MBIM patch for libmbim/libqmi.  Right now the tool I uploaded before is working fine.<br><br></div><div>I also need to see if Sierra Wireless has a new firmware available on their site.  Mine is new as of July, but a fix could be in right now.<br><br></div><div>BTW I have an ATT and a T-Mobile SIM card, both on pre-pay plans.<br></div><div><br></div>Collin<br><br><div><div><div><br></div></div></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Sun, Aug 30, 2015 at 1:33 PM, Ward, David - 0665 - MITLL <span dir="ltr"><<a href="mailto:david.ward@ll.mit.edu" target="_blank">david.ward@ll.mit.edu</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div class="HOEnZb"><div class="h5">On 08/30/2015 02:21 AM, David Ward wrote:<br>
> On 08/20/2015 12:43 PM, Dan Williams wrote:<br>
>> CDMA-capable modems (like a Sierra EM7355) will fail to even enable,<br>
>> because the internal CDMA code tries to initialize using AT commands and<br>
>> that fails because many MBIM modems don't have an AT port.  We should<br>
>> figure out how to support minimal MBIM + CDMA using MBIM instead of<br>
>> AT-anything.<br>
><br>
> Not only does this fix allow me to use MBIM on a Dell Wireless 5808e<br>
> (branded Sierra Wireless EM7355)...<br>
><br>
> I now seem to be able to use MBIM directly from a cold boot, without<br>
> ever switching to the QMI configuration. And for that matter, the QMI<br>
> configuration no longer seems to require the FCC Auth command; the<br>
> modem goes directly to an online state even if ModemManager is<br>
> disabled at startup. I have disconnected the laptop from both AC and<br>
> battery for 10 minutes and then this still works. I'm quite confident<br>
> this was not possible three weeks ago.<br>
><br>
> Was this a Verizon over-the-air firmware update perhaps? Is anyone<br>
> else with this modem noticing this too?<br>
><br>
> # qmicli -p -d /dev/cdc-wdm0 --dms-get-revision<br>
> [/dev/cdc-wdm0] Device revision retrieved:<br>
>     Revision: 'SWI9X15C_05.05.16.03 r22385 carmd-fwbuild1 2014/06/04<br>
> 15:01:26'<br>
<br>
</div></div>I left out one potentially relevant detail: a data plan was only<br>
activated on this modem this past week. But prior to that (when I was<br>
still using QMI with the FCC Auth command), the modem still connected to<br>
the network, and my browser just redirected me to a Verizon landing page<br>
for activating a data plan instead.<br>
<div class="HOEnZb"><div class="h5">_______________________________________________<br>
ModemManager-devel mailing list<br>
<a href="mailto:ModemManager-devel@lists.freedesktop.org">ModemManager-devel@lists.freedesktop.org</a><br>
<a href="http://lists.freedesktop.org/mailman/listinfo/modemmanager-devel" rel="noreferrer" target="_blank">http://lists.freedesktop.org/mailman/listinfo/modemmanager-devel</a><br>
</div></div></blockquote></div><br></div>