[PATCH 1/4] drm/amd/display: cleanup codestyle type BLOCK_COMMENT_STYLE on dc_link

Melissa Wen melissa.srw at gmail.com
Tue Mar 31 10:57:34 UTC 2020


Solve comments alignment problems on dc_link file

Signed-off-by: Melissa Wen <melissa.srw at gmail.com>
---
 drivers/gpu/drm/amd/display/dc/core/dc_link.c | 25 +++++++++++--------
 1 file changed, 15 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/amd/display/dc/core/dc_link.c b/drivers/gpu/drm/amd/display/dc/core/dc_link.c
index 67cfff1586e9..f580b533db5f 100644
--- a/drivers/gpu/drm/amd/display/dc/core/dc_link.c
+++ b/drivers/gpu/drm/amd/display/dc/core/dc_link.c
@@ -64,11 +64,11 @@
 enum {
 	PEAK_FACTOR_X1000 = 1006,
 	/*
-	* Some receivers fail to train on first try and are good
-	* on subsequent tries. 2 retries should be plenty. If we
-	* don't have a successful training then we don't expect to
-	* ever get one.
-	*/
+	 * Some receivers fail to train on first try and are good
+	 * on subsequent tries. 2 retries should be plenty. If we
+	 * don't have a successful training then we don't expect to
+	 * ever get one.
+	 */
 	LINK_TRAINING_MAX_VERIFY_RETRY = 2
 };
 
@@ -270,7 +270,8 @@ static enum ddc_transaction_type get_ddc_transaction_type(
 	case SIGNAL_TYPE_DISPLAY_PORT_MST:
 		/* MST does not use I2COverAux, but there is the
 		 * SPECIAL use case for "immediate dwnstrm device
-		 * access" (EPR#370830). */
+		 * access" (EPR#370830).
+		 */
 		transaction_type = DDC_TRANSACTION_TYPE_I2C_OVER_AUX;
 		break;
 
@@ -369,7 +370,8 @@ bool dc_link_is_dp_sink_present(struct dc_link *link)
 	/* Open GPIO and set it to I2C mode */
 	/* Note: this GpioMode_Input will be converted
 	 * to GpioConfigType_I2cAuxDualMode in GPIO component,
-	 * which indicates we need additional delay */
+	 * which indicates we need additional delay
+	 */
 
 	if (GPIO_RESULT_OK != dal_ddc_open(
 		ddc, GPIO_MODE_INPUT, GPIO_DDC_CONFIG_TYPE_MODE_I2C)) {
@@ -414,14 +416,16 @@ static enum signal_type link_detect_sink(
 		link->link_enc->id, link->link_id);
 
 	/* Internal digital encoder will detect only dongles
-	 * that require digital signal */
+	 * that require digital signal
+	 */
 
 	/* Detection mechanism is different
 	 * for different native connectors.
 	 * LVDS connector supports only LVDS signal;
 	 * PCIE is a bus slot, the actual connector needs to be detected first;
 	 * eDP connector supports only eDP signal;
-	 * HDMI should check straps for audio */
+	 * HDMI should check straps for audio
+	 */
 
 	/* PCIE detects the actual connector on add-on board */
 
@@ -432,7 +436,8 @@ static enum signal_type link_detect_sink(
 	switch (link->link_id.id) {
 	case CONNECTOR_ID_HDMI_TYPE_A: {
 		/* check audio support:
-		 * if native HDMI is not supported, switch to DVI */
+		 * if native HDMI is not supported, switch to DVI
+		 */
 		struct audio_support *aud_support = &link->dc->res_pool->audio_support;
 
 		if (!aud_support->hdmi_audio_native)
-- 
2.25.1



More information about the amd-gfx mailing list