[PATCH AUTOSEL 5.19 012/105] drm/amd/display: Detect dpcd_rev when hotplug mst monitor

Sasha Levin sashal at kernel.org
Thu Aug 11 15:26:56 UTC 2022


From: Wayne Lin <Wayne.Lin at amd.com>

[ Upstream commit 453b0016a054df0f442fda8a145b97a33816cab9 ]

[Why]
Once mst topology is constructed, later on new connected monitors
are reported to source by CSN message. Within CSN, there is no
carried info of DPCD_REV comparing to LINK_ADDRESS reply. As the
result, we might leave some ports connected to DP but without DPCD
revision number which will affect us determining the capability of
the DP Rx.

[How]
Send out remote DPCD read when the port's dpcd_rev is 0x0 in
detect_ctx(). Firstly, read out the value from DPCD 0x2200. If the
return value is 0x0, it's likely the DP1.2 DP Rx then we reques
revision from DPCD 0x0 again.

Reviewed-by: Hersen Wu <hersenwu at amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz at amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin at amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler at amd.com>
Signed-off-by: Alex Deucher <alexander.deucher at amd.com>
Signed-off-by: Sasha Levin <sashal at kernel.org>
---
 .../display/amdgpu_dm/amdgpu_dm_mst_types.c   | 38 ++++++++++++++++++-
 1 file changed, 37 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
index 2b9b095e5f03..1c02d873950d 100644
--- a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
+++ b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
@@ -361,12 +361,48 @@ dm_dp_mst_detect(struct drm_connector *connector,
 {
 	struct amdgpu_dm_connector *aconnector = to_amdgpu_dm_connector(connector);
 	struct amdgpu_dm_connector *master = aconnector->mst_port;
+	struct drm_dp_mst_port *port = aconnector->port;
+	int connection_status;
 
 	if (drm_connector_is_unregistered(connector))
 		return connector_status_disconnected;
 
-	return drm_dp_mst_detect_port(connector, ctx, &master->mst_mgr,
+	connection_status = drm_dp_mst_detect_port(connector, ctx, &master->mst_mgr,
 				      aconnector->port);
+
+	if (port->pdt != DP_PEER_DEVICE_NONE && !port->dpcd_rev) {
+		uint8_t dpcd_rev;
+		int ret;
+
+		ret = drm_dp_dpcd_readb(&port->aux, DP_DP13_DPCD_REV, &dpcd_rev);
+
+		if (ret == 1) {
+			port->dpcd_rev = dpcd_rev;
+
+			/* Could be DP1.2 DP Rx case*/
+			if (!dpcd_rev) {
+				ret = drm_dp_dpcd_readb(&port->aux, DP_DPCD_REV, &dpcd_rev);
+
+				if (ret == 1)
+					port->dpcd_rev = dpcd_rev;
+			}
+
+			if (!dpcd_rev)
+				DRM_DEBUG_KMS("Can't decide DPCD revision number!");
+		}
+
+		/*
+		 * Could be legacy sink, logical port etc on DP1.2.
+		 * Will get Nack under these cases when issue remote
+		 * DPCD read.
+		 */
+		if (ret != 1)
+			DRM_DEBUG_KMS("Can't access DPCD");
+	} else if (port->pdt == DP_PEER_DEVICE_NONE) {
+		port->dpcd_rev = 0;
+	}
+
+	return connection_status;
 }
 
 static int dm_dp_mst_atomic_check(struct drm_connector *connector,
-- 
2.35.1



More information about the amd-gfx mailing list