New i915 warning from intel_dp_aux_ch
Meelis Roos
mroos at ut.ee
Mon Jan 21 01:25:20 PST 2013
While testing out 3.8.0-rc4-00071-g9a92841 on a PC where I have
ironlake_crtc_disable warning
(https://bugzilla.kernel.org/show_bug.cgi?id=52061), I saw a new warning
today that was not there with 3.8.0-rc3-00074. The previous warning is
also still there.
EDID is occasionally wrong on this PC, probably some timing issue in
trying to read it out.
It is not 100% reproducible - happened 3 out of 6 reboots. It happens
together with the EDID warning - probably related. But since it is not
always there, I do now knwo exactly since when it might be present.
I managed to capture drm.debug=0xe output, full dmesg with debug is
below is the main one.
[ 0.270838] i915 0000:00:02.0: setting latency timer to 64
[ 0.283426] i915 0000:00:02.0: irq 40 for MSI/MSI-X
[ 0.283431] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 0.283470] [drm] Driver supports precise vblank timestamp query.
[ 0.283532] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 0.366758] [drm:intel_dp_aux_ch] *ERROR* dp_aux_ch not done status 0x0015003f
[ 0.375148] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 142
[ 0.375210] Raw EDID:
[ 0.375239] 00 ff ff ff ff ff ff 00 22 f0 49 29 00 00 00 00
[ 0.375275] 15 15 01 04 a5 33 1d 78 26 01 f5 a2 57 52 9f 27
[ 0.375312] 0a 50 54 a1 08 00 81 c0 81 80 95 00 b3 00 d1 c0
[ 0.375348] 01 01 01 01 01 01 02 3a 80 18 71 38 2d 40 58 2c
[ 0.375385] 45 00 fe 1f 11 00 00 1e 00 00 00 fd 00 32 4c 18
[ 0.375421] 5e 11 00 0a 0a 0a 0a 0a 20 20 20 20 20 00 00 00
[ 0.375458] fc 00 48 50 20 4c 41 32 33 30 36 0a 20 20 20 00
[ 0.375495] 00 00 ff 00 43 4e 43 31 32 31 31 32 50 42 0a 20
[ 0.389465] ------------[ cut here ]------------
[ 0.389502] WARNING: at drivers/gpu/drm/i915/intel_dp.c:410 intel_dp_aux_ch+0x131/0x4e0()
[ 0.389563] Hardware name: HP Compaq 8100 Elite SFF PC
[ 0.389598] dp_aux_ch not started status 0x8025003f
[ 0.389632] Modules linked in:
[ 0.389671] Pid: 6, comm: kworker/u:0 Not tainted 3.8.0-rc4-00071-g9a92841 #80
[ 0.389729] Call Trace:
[ 0.389762] [<ffffffff81036a29>] ? warn_slowpath_common+0x79/0xc0
[ 0.389801] [<ffffffff81036b25>] ? warn_slowpath_fmt+0x45/0x50
[ 0.389838] [<ffffffff812d7d61>] ? intel_dp_aux_ch+0x131/0x4e0
[ 0.389877] [<ffffffff812d82e2>] ? intel_dp_aux_native_write+0xa2/0xe0
[ 0.389916] [<ffffffff812d8021>] ? intel_dp_aux_ch+0x3f1/0x4e0
[ 0.389953] [<ffffffff812d8fbc>] ? intel_dp_set_link_train+0xbc/0x300
[ 0.389993] [<ffffffff812d82e2>] ? intel_dp_aux_native_write+0xa2/0xe0
[ 0.390032] [<ffffffff812da2f2>] ? intel_dp_start_link_train+0xf2/0x2f0
[ 0.390072] [<ffffffff812da831>] ? intel_dp_check_link_status+0x91/0x180
[ 0.390113] [<ffffffff812a8bce>] ? i915_hotplug_work_func+0x6e/0xa0
[ 0.390153] [<ffffffff8104d1e0>] ? process_one_work+0x120/0x430
[ 0.390686] [<ffffffff812a8b60>] ? i915_error_work_func+0x100/0x100
[ 0.390725] [<ffffffff8104ef7d>] ? worker_thread+0x15d/0x450
[ 0.390762] [<ffffffff8104ee20>] ? schedule_delayed_work+0x20/0x20
[ 0.390801] [<ffffffff81053ca3>] ? kthread+0xb3/0xc0
[ 0.390837] [<ffffffff81053bf0>] ? kthread_create_on_node+0x110/0x110
[ 0.390878] [<ffffffff8145a7ec>] ? ret_from_fork+0x7c/0xb0
[ 0.390917] [<ffffffff81053bf0>] ? kthread_create_on_node+0x110/0x110
[ 0.390958] ---[ end trace 0f2d76d213a31275 ]---
[ 0.000000] Linux version 3.8.0-rc4-00071-g9a92841 (mroos at prometheus) (gcc version 4.7.2 (Debian 4.7.2-5) ) #80 SMP Mon Jan 21 09:52:32 EET 2013
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.8.0-rc4-00071-g9a92841 root=/dev/sda1 ro drm.debug=0xe
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e8000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000db7ac43f] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db7ac440-0x00000000db7ae49f] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000db7ae4a0-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fed3ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed45000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000117ffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: Hewlett-Packard HP Compaq 8100 Elite SFF PC/304Ah, BIOS 786H1 v01.13 07/14/2011
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x118000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E3FFF write-protect
[ 0.000000] E4000-EFFFF write-back
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask E00000000 write-back
[ 0.000000] 1 base 0DB800000 mask FFF800000 uncachable
[ 0.000000] 2 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 3 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xdb800000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdb7ac max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f9bf0-0x000f9bff] mapped at [ffff8800000f9bf0]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0xdb7abfff]
[ 0.000000] [mem 0x00000000-0xdb5fffff] page 2M
[ 0.000000] [mem 0xdb600000-0xdb7abfff] page 4k
[ 0.000000] kernel direct mapping tables up to 0xdb7abfff @ [mem 0x1fffa000-0x1fffffff]
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x117ffffff]
[ 0.000000] [mem 0x100000000-0x117ffffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0x117ffffff @ [mem 0xdb7aa000-0xdb7abfff]
[ 0.000000] ACPI: RSDP 00000000000e5210 00014 (v00 COMPAQ)
[ 0.000000] ACPI: RSDT 00000000db7d0540 00040 (v01 HPQOEM SLIC-BPC 20110714 00000000)
[ 0.000000] ACPI: FACP 00000000db7d05e8 00074 (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI BIOS Bug: Warning: Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000050/0x0 (20121018/tbfadt-598)
[ 0.000000] ACPI BIOS Bug: Warning: Invalid length for FADT/Pm2ControlBlock: 0, using default 8 (20121018/tbfadt-648)
[ 0.000000] ACPI: DSDT 00000000db7d0a4f 0A69E (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
[ 0.000000] ACPI: FACS 00000000db7d0500 00040
[ 0.000000] ACPI: APIC 00000000db7d065c 000BC (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: ASF! 00000000db7d0718 00063 (v32 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: MCFG 00000000db7d077b 0003C (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: TCPA 00000000db7d07b7 00032 (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: SLIC 00000000db7d07e9 00176 (v01 HPQOEM SLIC-BPC 00000001 00000000)
[ 0.000000] ACPI: HPET 00000000db7d095f 00038 (v01 COMPAQ IBEXPEAK 00000001 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880113800000-ffff8801175fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x117ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xdb7abfff]
[ 0.000000] node 0: [mem 0x100000000-0x117ffffff]
[ 0.000000] On node 0 totalpages: 997179
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3913 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13983 pages used for memmap
[ 0.000000] DMA32 zone: 880909 pages, LIFO batch:31
[ 0.000000] Normal zone: 1536 pages used for memmap
[ 0.000000] Normal zone: 96768 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0xf808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000db7ac000 - 00000000db7ad000
[ 0.000000] PM: Registered nosave memory: 00000000db7ad000 - 00000000db7ae000
[ 0.000000] PM: Registered nosave memory: 00000000db7ae000 - 00000000db7af000
[ 0.000000] PM: Registered nosave memory: 00000000db7af000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f4000000
[ 0.000000] PM: Registered nosave memory: 00000000f4000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fe000000
[ 0.000000] PM: Registered nosave memory: 00000000fe000000 - 00000000fed40000
[ 0.000000] PM: Registered nosave memory: 00000000fed40000 - 00000000fed45000
[ 0.000000] PM: Registered nosave memory: 00000000fed45000 - 0000000100000000
[ 0.000000] e820: [mem 0xe0000000-0xf3ffffff] available for PCI devices
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880117c00000 s74304 r8192 d24000 u262144
[ 0.000000] pcpu-alloc: s74304 r8192 d24000 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 981590
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.8.0-rc4-00071-g9a92841 root=/dev/sda1 ro drm.debug=0xe
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Memory: 3842424k/4587520k available (4473k kernel code, 598804k absent, 146292k reserved, 4072k data, 492k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:744 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 3325.340 MHz processor
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 6650.68 BogoMIPS (lpj=13301360)
[ 0.000062] pid_max: default: 32768 minimum: 301
[ 0.000110] Mount-cache hash table entries: 256
[ 0.000253] CPU: Physical Processor ID: 0
[ 0.000280] CPU: Processor Core ID: 0
[ 0.000308] mce: CPU supports 9 MCE banks
[ 0.000342] CPU0: Thermal monitoring enabled (TM1)
[ 0.000375] process: using mwait in idle threads
[ 0.000405] Last level iTLB entries: 4KB 512, 2MB 7, 4MB 7
[ 0.000405] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
[ 0.000405] tlb_flushall_shift: 6
[ 0.000553] Freeing SMP alternatives: 20k freed
[ 0.000587] ACPI: Core revision 20121018
[ 0.004748] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.044347] smpboot: CPU0: Intel(R) Core(TM) i5 CPU 660 @ 3.33GHz (fam: 06, model: 25, stepping: 05)
[ 0.151287] Performance Events: PEBS fmt1+, 16-deep LBR, Westmere events, Intel PMU driver.
[ 0.151367] perf_event_intel: CPUID marked event: 'bus cycles' unavailable
[ 0.151407] ... version: 3
[ 0.151439] ... bit width: 48
[ 0.151471] ... generic registers: 4
[ 0.151504] ... value mask: 0000ffffffffffff
[ 0.151540] ... max period: 000000007fffffff
[ 0.151575] ... fixed-purpose events: 3
[ 0.151607] ... event mask: 000000070000000f
[ 0.165028] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.151766] smpboot: Booting Node 0, Processors #1 #2 #3
[ 0.191408] Brought up 4 CPUs
[ 0.191464] smpboot: Total of 4 processors activated (26602.72 BogoMIPS)
[ 0.193322] PM: Registering ACPI NVS region [mem 0xdb7ac440-0xdb7ae49f] (8288 bytes)
[ 0.193389] reboot: BIOS series board detected. Selecting HP Compaq Laptop-method for reboots.
[ 0.193492] NET: Registered protocol family 16
[ 0.193596] ACPI: bus type pci registered
[ 0.193666] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[ 0.193731] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[ 0.196352] PCI: Using configuration type 1 for base access
[ 0.196773] bio: create slab <bio-0> at 0
[ 0.196841] ACPI: Added _OSI(Module Device)
[ 0.196875] ACPI: Added _OSI(Processor Device)
[ 0.196910] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.196944] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.197466] ACPI: EC: Look up EC in DSDT
[ 0.202202] ACPI: SSDT 00000000db7dc771 003BA (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.202430] ACPI: Dynamic OEM Table Load:
[ 0.202471] ACPI: SSDT (null) 003BA (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.202606] ACPI: SSDT 00000000db7dc399 003D8 (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.202811] ACPI: Dynamic OEM Table Load:
[ 0.202851] ACPI: SSDT (null) 003D8 (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.206327] ACPI: Interpreter enabled
[ 0.206361] ACPI: (supports S0 S3 S4 S5)
[ 0.206418] ACPI: Using IOAPIC for interrupt routing
[ 0.208537] ACPI: No dock devices found.
[ 0.208572] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.208749] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.208789] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.208889] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20121018/dsfield-211)
[ 0.208966] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880113432668), AE_ALREADY_EXISTS (20121018/psparse-537)
[ 0.209053] ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
[ 0.209123] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20121018/nspredef-359)
[ 0.209225] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20121018/dsfield-211)
[ 0.209300] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880113432668), AE_ALREADY_EXISTS (20121018/psparse-537)
[ 0.209881] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20121018/nspredef-359)
[ 0.209960] pci_root PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.210022] pci_root PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.210260] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.210345] PCI host bridge to bus 0000:00
[ 0.210379] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.210415] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfdffffff]
[ 0.210455] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.210493] pci_bus 0000:00: root bus resource [io 0x1000-0x2fff]
[ 0.210531] pci_bus 0000:00: root bus resource [io 0x3000-0x6fff]
[ 0.210569] pci_bus 0000:00: root bus resource [io 0x7000-0xafff]
[ 0.210606] pci_bus 0000:00: root bus resource [io 0xb000-0xffff]
[ 0.210644] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.210684] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xf3ffffff]
[ 0.210723] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.210768] pci 0000:00:00.0: [8086:0040] type 00 class 0x060000
[ 0.210781] DMAR: Disabling batched IOTLB flush on Ironlake
[ 0.210832] pci 0000:00:02.0: [8086:0042] type 00 class 0x030000
[ 0.210840] pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf03fffff 64bit]
[ 0.210844] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.210848] pci 0000:00:02.0: reg 20: [io 0x1170-0x1177]
[ 0.210890] pci 0000:00:16.0: [8086:3b64] type 00 class 0x078000
[ 0.210915] pci 0000:00:16.0: reg 10: [mem 0xf0427100-0xf042710f 64bit]
[ 0.211002] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.211023] pci 0000:00:16.3: [8086:3b67] type 00 class 0x070002
[ 0.211037] pci 0000:00:16.3: reg 10: [io 0x1188-0x118f]
[ 0.211044] pci 0000:00:16.3: reg 14: [mem 0xf0424000-0xf0424fff]
[ 0.211132] pci 0000:00:19.0: [8086:10ef] type 00 class 0x020000
[ 0.211145] pci 0000:00:19.0: reg 10: [mem 0xf0400000-0xf041ffff]
[ 0.211152] pci 0000:00:19.0: reg 14: [mem 0xf0425000-0xf0425fff]
[ 0.211158] pci 0000:00:19.0: reg 18: [io 0x1100-0x111f]
[ 0.211206] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.211225] pci 0000:00:1a.0: [8086:3b3c] type 00 class 0x0c0320
[ 0.211242] pci 0000:00:1a.0: reg 10: [mem 0xf0426800-0xf0426bff]
[ 0.211314] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.211334] pci 0000:00:1b.0: [8086:3b56] type 00 class 0x040300
[ 0.211346] pci 0000:00:1b.0: reg 10: [mem 0xf0420000-0xf0423fff 64bit]
[ 0.211398] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.211414] pci 0000:00:1c.0: [8086:3b42] type 01 class 0x060400
[ 0.211467] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.211486] pci 0000:00:1c.4: [8086:3b4a] type 01 class 0x060400
[ 0.211538] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.211554] pci 0000:00:1c.6: [8086:3b4e] type 01 class 0x060400
[ 0.211605] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[ 0.211628] pci 0000:00:1d.0: [8086:3b34] type 00 class 0x0c0320
[ 0.211644] pci 0000:00:1d.0: reg 10: [mem 0xf0426c00-0xf0426fff]
[ 0.211716] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.211733] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.211780] pci 0000:00:1f.0: [8086:3b0a] type 00 class 0x060100
[ 0.211882] pci 0000:00:1f.2: [8086:3b22] type 00 class 0x010601
[ 0.211896] pci 0000:00:1f.2: reg 10: [io 0x1190-0x1197]
[ 0.211901] pci 0000:00:1f.2: reg 14: [io 0x11a8-0x11ab]
[ 0.211908] pci 0000:00:1f.2: reg 18: [io 0x1198-0x119f]
[ 0.211913] pci 0000:00:1f.2: reg 1c: [io 0x11ac-0x11af]
[ 0.211919] pci 0000:00:1f.2: reg 20: [io 0x1120-0x113f]
[ 0.211925] pci 0000:00:1f.2: reg 24: [mem 0xf0426000-0xf04267ff]
[ 0.211959] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.212000] pci 0000:00:1c.0: PCI bridge to [bus 18]
[ 0.212068] pci 0000:00:1c.4: PCI bridge to [bus 24]
[ 0.212136] pci 0000:00:1c.6: PCI bridge to [bus 30]
[ 0.212221] pci 0000:00:1e.0: PCI bridge to [bus 0d] (subtractive decode)
[ 0.212266] pci 0000:00:1e.0: bridge window [mem 0xf8000000-0xfdffffff] (subtractive decode)
[ 0.212267] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.212268] pci 0000:00:1e.0: bridge window [io 0x1000-0x2fff] (subtractive decode)
[ 0.212269] pci 0000:00:1e.0: bridge window [io 0x3000-0x6fff] (subtractive decode)
[ 0.212271] pci 0000:00:1e.0: bridge window [io 0x7000-0xafff] (subtractive decode)
[ 0.212272] pci 0000:00:1e.0: bridge window [io 0xb000-0xffff] (subtractive decode)
[ 0.212273] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.212274] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xf3ffffff] (subtractive decode)
[ 0.212275] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 0.212288] pci_bus 0000:00: on NUMA node 0
[ 0.212300] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX1._PRT]
[ 0.212326] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX5._PRT]
[ 0.212349] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX7._PRT]
[ 0.212371] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
[ 0.212424] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.215605] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.215712] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.215817] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.215922] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.216026] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.216131] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.216236] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.216342] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.216484] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.216546] vgaarb: loaded
[ 0.216576] vgaarb: bridge control possible 0000:00:02.0
[ 0.216641] SCSI subsystem initialized
[ 0.216674] ACPI: bus type scsi registered
[ 0.216726] libata version 3.00 loaded.
[ 0.216742] PCI: Using ACPI for IRQ routing
[ 0.217878] PCI: Discovered peer bus 3f
[ 0.217910] PCI: root bus 3f: using default resources
[ 0.217911] PCI: Probing PCI hardware (bus 3f)
[ 0.217924] PCI host bridge to bus 0000:3f
[ 0.217957] pci_bus 0000:3f: root bus resource [io 0x0000-0xffff]
[ 0.217995] pci_bus 0000:3f: root bus resource [mem 0x00000000-0xfffffffff]
[ 0.218035] pci_bus 0000:3f: No busn resource found for root bus, will use [bus 3f-ff]
[ 0.218099] pci 0000:3f:00.0: [8086:2c61] type 00 class 0x060000
[ 0.218112] pci 0000:3f:00.1: [8086:2d01] type 00 class 0x060000
[ 0.218128] pci 0000:3f:02.0: [8086:2d10] type 00 class 0x060000
[ 0.218140] pci 0000:3f:02.1: [8086:2d11] type 00 class 0x060000
[ 0.218152] pci 0000:3f:02.2: [8086:2d12] type 00 class 0x060000
[ 0.218164] pci 0000:3f:02.3: [8086:2d13] type 00 class 0x060000
[ 0.218182] pci_bus 0000:3f: busn_res: [bus 3f-ff] end is updated to 3f
[ 0.218245] PCI: pci_cache_line_size set to 64 bytes
[ 0.218278] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[ 0.218279] e820: reserve RAM buffer [mem 0xdb7ac440-0xdbffffff]
[ 0.218346] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.218421] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.220457] Switching to clocksource hpet
[ 0.220523] pnp: PnP ACPI init
[ 0.220558] ACPI: bus type pnp registered
[ 0.220617] pnp 00:00: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.220625] pnp 00:01: [dma 4]
[ 0.220633] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.220649] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.220661] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.220676] pnp 00:04: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
[ 0.220692] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.220843] pnp 00:06: [dma 3]
[ 0.220878] pnp 00:06: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.221027] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
[ 0.221065] pnp 00:08: Plug and Play ACPI device, IDs PNP0003 (active)
[ 0.221079] pnp 00:09: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 0.221105] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.221220] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.221246] system 00:0c: [io 0x04d0-0x04d1] has been reserved
[ 0.221285] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.221312] system 00:0d: [io 0x0400-0x041f] has been reserved
[ 0.221350] system 00:0d: [io 0x0420-0x043f] has been reserved
[ 0.221388] system 00:0d: [io 0x0440-0x045f] has been reserved
[ 0.221425] system 00:0d: [io 0x0460-0x047f] has been reserved
[ 0.221462] system 00:0d: [io 0x0480-0x048f] has been reserved
[ 0.221500] system 00:0d: [io 0xf800-0xf81f] has been reserved
[ 0.221537] system 00:0d: [io 0xf820-0xf83f] has been reserved
[ 0.221575] system 00:0d: [io 0xf840-0xf85f] has been reserved
[ 0.221612] system 00:0d: [io 0xf860-0xf87f] has been reserved
[ 0.221649] system 00:0d: [io 0xfa00-0xfa3f] has been reserved
[ 0.221687] system 00:0d: [io 0xfc00-0xfc7f] has been reserved
[ 0.221724] system 00:0d: [io 0xfc80-0xfcff] has been reserved
[ 0.221761] system 00:0d: [io 0xfe00-0xfe7f] has been reserved
[ 0.221800] system 00:0d: [io 0xfe80-0xfeff] has been reserved
[ 0.221838] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.222009] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.222051] system 00:0e: [mem 0x00100000-0xdfffffff] could not be reserved
[ 0.222091] system 00:0e: [mem 0x000e4000-0x000fffff] could not be reserved
[ 0.222131] system 00:0e: [mem 0xfec01000-0xfecfffff] has been reserved
[ 0.222170] system 00:0e: [mem 0xfed00400-0xfed3ffff] has been reserved
[ 0.222209] system 00:0e: [mem 0xfed45000-0xffffffff] has been reserved
[ 0.222248] system 00:0e: [mem 0xf4000000-0xf7ffffff] has been reserved
[ 0.222287] system 00:0e: [mem 0x000cfe00-0x000e3fff] has been reserved
[ 0.222327] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.222334] pnp: PnP ACPI: found 15 devices
[ 0.222367] ACPI: ACPI bus type pnp unregistered
[ 0.227356] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 18] add_size 1000
[ 0.227359] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 18] add_size 200000
[ 0.227361] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 18] add_size 200000
[ 0.227367] pci 0000:00:1c.4: bridge window [io 0x1000-0x0fff] to [bus 24] add_size 1000
[ 0.227369] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 24] add_size 200000
[ 0.227370] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff] to [bus 24] add_size 200000
[ 0.227376] pci 0000:00:1c.6: bridge window [io 0x1000-0x0fff] to [bus 30] add_size 1000
[ 0.227377] pci 0000:00:1c.6: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 30] add_size 200000
[ 0.227379] pci 0000:00:1c.6: bridge window [mem 0x00100000-0x000fffff] to [bus 30] add_size 200000
[ 0.227389] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.227390] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.227391] pci 0000:00:1c.4: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.227393] pci 0000:00:1c.4: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.227394] pci 0000:00:1c.6: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.227396] pci 0000:00:1c.6: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.227397] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.227399] pci 0000:00:1c.4: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.227400] pci 0000:00:1c.6: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.227403] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf8000000-0xf81fffff]
[ 0.227443] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.227504] pci 0000:00:1c.4: BAR 14: assigned [mem 0xf8400000-0xf85fffff]
[ 0.227544] pci 0000:00:1c.4: BAR 15: assigned [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.227604] pci 0000:00:1c.6: BAR 14: assigned [mem 0xf8800000-0xf89fffff]
[ 0.227644] pci 0000:00:1c.6: BAR 15: assigned [mem 0xf8a00000-0xf8bfffff 64bit pref]
[ 0.227706] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.227744] pci 0000:00:1c.4: BAR 13: assigned [io 0x3000-0x3fff]
[ 0.227783] pci 0000:00:1c.6: BAR 13: assigned [io 0x4000-0x4fff]
[ 0.227821] pci 0000:00:1c.0: PCI bridge to [bus 18]
[ 0.227857] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.227897] pci 0000:00:1c.0: bridge window [mem 0xf8000000-0xf81fffff]
[ 0.227938] pci 0000:00:1c.0: bridge window [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.228001] pci 0000:00:1c.4: PCI bridge to [bus 24]
[ 0.228036] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
[ 0.228076] pci 0000:00:1c.4: bridge window [mem 0xf8400000-0xf85fffff]
[ 0.228117] pci 0000:00:1c.4: bridge window [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.228180] pci 0000:00:1c.6: PCI bridge to [bus 30]
[ 0.228215] pci 0000:00:1c.6: bridge window [io 0x4000-0x4fff]
[ 0.228255] pci 0000:00:1c.6: bridge window [mem 0xf8800000-0xf89fffff]
[ 0.228295] pci 0000:00:1c.6: bridge window [mem 0xf8a00000-0xf8bfffff 64bit pref]
[ 0.228358] pci 0000:00:1e.0: PCI bridge to [bus 0d]
[ 0.228418] pci 0000:00:1e.0: setting latency timer to 64
[ 0.228421] pci_bus 0000:00: resource 4 [mem 0xf8000000-0xfdffffff]
[ 0.228422] pci_bus 0000:00: resource 5 [io 0x0000-0x0cf7]
[ 0.228423] pci_bus 0000:00: resource 6 [io 0x1000-0x2fff]
[ 0.228424] pci_bus 0000:00: resource 7 [io 0x3000-0x6fff]
[ 0.228426] pci_bus 0000:00: resource 8 [io 0x7000-0xafff]
[ 0.228427] pci_bus 0000:00: resource 9 [io 0xb000-0xffff]
[ 0.228428] pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.228429] pci_bus 0000:00: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 0.228430] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.228432] pci_bus 0000:18: resource 0 [io 0x2000-0x2fff]
[ 0.228433] pci_bus 0000:18: resource 1 [mem 0xf8000000-0xf81fffff]
[ 0.228434] pci_bus 0000:18: resource 2 [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.228435] pci_bus 0000:24: resource 0 [io 0x3000-0x3fff]
[ 0.228437] pci_bus 0000:24: resource 1 [mem 0xf8400000-0xf85fffff]
[ 0.228438] pci_bus 0000:24: resource 2 [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.228439] pci_bus 0000:30: resource 0 [io 0x4000-0x4fff]
[ 0.228440] pci_bus 0000:30: resource 1 [mem 0xf8800000-0xf89fffff]
[ 0.228442] pci_bus 0000:30: resource 2 [mem 0xf8a00000-0xf8bfffff 64bit pref]
[ 0.228443] pci_bus 0000:0d: resource 4 [mem 0xf8000000-0xfdffffff]
[ 0.228444] pci_bus 0000:0d: resource 5 [io 0x0000-0x0cf7]
[ 0.228445] pci_bus 0000:0d: resource 6 [io 0x1000-0x2fff]
[ 0.228447] pci_bus 0000:0d: resource 7 [io 0x3000-0x6fff]
[ 0.228448] pci_bus 0000:0d: resource 8 [io 0x7000-0xafff]
[ 0.228449] pci_bus 0000:0d: resource 9 [io 0xb000-0xffff]
[ 0.228450] pci_bus 0000:0d: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.228451] pci_bus 0000:0d: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 0.228452] pci_bus 0000:0d: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.228454] pci_bus 0000:3f: resource 4 [io 0x0000-0xffff]
[ 0.228455] pci_bus 0000:3f: resource 5 [mem 0x00000000-0xfffffffff]
[ 0.228475] NET: Registered protocol family 2
[ 0.228585] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.228711] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.228816] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.228875] TCP: reno registered
[ 0.228907] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.228954] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.229040] NET: Registered protocol family 1
[ 0.229081] pci 0000:00:02.0: Boot video device
[ 0.229138] PCI: CLS 64 bytes, default 64
[ 0.229150] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.229189] software IO TLB [mem 0xd77aa000-0xdb7aa000] (64MB) mapped at [ffff8800d77aa000-ffff8800db7a9fff]
[ 0.229579] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.230346] VFS: Disk quotas dquot_6.5.2
[ 0.230403] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.230610] msgmni has been set to 7504
[ 0.230798] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.230859] io scheduler noop registered
[ 0.230891] io scheduler deadline registered
[ 0.230926] io scheduler cfq registered (default)
[ 0.231079] intel_idle: MWAIT substates: 0x1120
[ 0.231080] intel_idle: v0.4 model 0x25
[ 0.231081] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.231137] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.231200] ACPI: Power Button [PBTN]
[ 0.231253] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.231313] ACPI: Power Button [PWRF]
[ 0.231367] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.251728] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.272035] 0000:00:16.3: ttyS1 at I/O 0x1188 (irq = 17) is a 16550A
[ 0.272173] Linux agpgart interface v0.103
[ 0.272233] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset
[ 0.272305] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 0.273011] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[ 0.273121] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 0.273193] [drm] Initialized drm 1.1.0 20060810
[ 0.273340] [drm:i915_dump_device_info], i915 device info: gen=5, pciid=0x0042 flags=need_gfx_hws,has_hotplug,has_bsd_ring,
[ 0.273347] i915 0000:00:02.0: setting latency timer to 64
[ 0.285867] [drm:intel_detect_pch], Found Ibex Peak PCH
[ 0.285917] [drm:intel_opregion_setup], graphic opregion physical addr: 0xdb7ac440
[ 0.285922] [drm:intel_opregion_setup], SWSCI supported
[ 0.285943] i915 0000:00:02.0: irq 40 for MSI/MSI-X
[ 0.285948] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 0.285987] [drm] Driver supports precise vblank timestamp query.
[ 0.286024] [drm:init_vbt_defaults], Set default to SSC at 100MHz
[ 0.286027] [drm:intel_parse_bios], Using VBT from OpRegion: $VBT IRONLAKE-DESK d
[ 0.286029] [drm:parse_general_features], BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 1 lvds_use_ssc 0 lvds_ssc_freq 120 display_clock_mode 0
[ 0.286030] [drm:parse_general_definitions], crt_ddc_bus_pin: 2
[ 0.286032] [drm:parse_lfp_panel_data], Found panel mode in BIOS VBT tables:
[ 0.286034] [drm:drm_mode_debug_printmodeline], Modeline 0:"1024x768" 0 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
[ 0.286036] [drm:parse_lfp_panel_data], VBT initial LVDS value 300
[ 0.286037] [drm:parse_sdvo_panel_data], Found SDVO panel mode in BIOS VBT tables:
[ 0.286038] [drm:drm_mode_debug_printmodeline], Modeline 0:"1600x1200" 0 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x8 0xa
[ 0.286040] [drm:parse_sdvo_device_mapping], No SDVO device info is found in VBT
[ 0.286046] [drm:intel_dsm_pci_probe], no _DSM method for intel device
[ 0.286054] [drm:intel_modeset_init], 2 display pipes available.
[ 0.286062] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 0.286465] [drm:intel_dp_i2c_init], i2c_init DPDDC-C
[ 0.287484] [drm:ironlake_init_pch_refclk], has_panel 0 has_lvds 0 has_pch_edp 0 has_cpu_edp 0 has_ck505 0
[ 0.287486] [drm:ironlake_init_pch_refclk], Disabling SSC entirely
[ 0.289198] [drm:init_status_page], render ring hws offset: 0x00001000
[ 0.289535] [drm:init_status_page], bsd ring hws offset: 0x00025000
[ 0.289870] [drm:intel_modeset_setup_hw_state], [CRTC:3] hw state readout: enabled
[ 0.289871] [drm:intel_modeset_setup_hw_state], [CRTC:5] hw state readout: disabled
[ 0.289873] [drm:intel_modeset_setup_hw_state], [ENCODER:8:DAC-8] hw state readout: disabled, pipe=0
[ 0.289875] [drm:intel_modeset_setup_hw_state], [ENCODER:9:TMDS-9] hw state readout: disabled, pipe=0
[ 0.289877] [drm:intel_modeset_setup_hw_state], [ENCODER:13:TMDS-13] hw state readout: enabled, pipe=0
[ 0.289880] [drm:intel_modeset_setup_hw_state], [CONNECTOR:7:VGA-1] hw state readout: disabled
[ 0.289881] [drm:intel_modeset_setup_hw_state], [CONNECTOR:10:HDMI-A-1] hw state readout: disabled
[ 0.289883] [drm:intel_modeset_setup_hw_state], [CONNECTOR:14:DP-1] hw state readout: enabled
[ 0.289888] [drm:intel_connector_check_state], [CONNECTOR:14:DP-1]
[ 0.289890] [drm:intel_modeset_check_state], [ENCODER:8:DAC-8]
[ 0.289892] [drm:intel_modeset_check_state], [ENCODER:9:TMDS-9]
[ 0.289894] [drm:intel_modeset_check_state], [ENCODER:13:TMDS-13]
[ 0.289895] [drm:intel_modeset_check_state], [CRTC:3]
[ 0.289897] [drm:intel_modeset_check_state], [CRTC:5]
[ 0.289900] [drm:intel_crt_reset], pch crt adpa set to 0xf40000
[ 0.289926] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 0.289928] [drm:intel_ironlake_crt_detect_hotplug], trigger hotplug detect cycle: adpa=0xf40000
[ 0.304248] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 0.304250] [drm:intel_crt_detect], CRT not detected via hotplug
[ 0.312224] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 0.312226] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 0.312227] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 0.312228] [drm:intel_gmbus_force_bit], enabling bit-banging on i915 gmbus vga. force bit now 1
[ 0.312542] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 0.312543] [drm:intel_gmbus_force_bit], disabling bit-banging on i915 gmbus vga. force bit now 0
[ 0.312544] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 0.312546] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 0.312547] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 0.320200] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 0.320201] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 0.320202] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 0.320203] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:14:DP-1]
[ 0.320512] [drm:intel_dp_detect], DPCD: 11 06 84 01 00 00 01 00 02 02 06 00 00 00 00
[ 0.321537] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.348538] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.349564] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.366540] [drm:i915_hotplug_work_func], running encoder hotplug functions
[ 0.372966] [drm:intel_dp_check_link_status], TMDS-13: channel EQ not ok, retraining
[ 0.377668] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.377670] [drm:drm_edid_block_valid] *ERROR* EDID checksum is invalid, remainder is 224
[ 0.377731] Raw EDID:
[ 0.377759] 00 ff ff ff ff ff ff 00 22 f0 49 29 00 00 00 00
[ 0.377796] 15 15 01 04 a5 33 1d 78 26 01 f5 a2 57 52 9f 27
[ 0.377833] 0a 50 54 a1 08 00 81 c0 81 80 95 00 b3 00 d1 c0
[ 0.377869] 01 01 01 01 01 01 02 3a 80 18 71 38 2d 40 58 2c
[ 0.377906] 45 00 fe 1f 11 00 00 1e 00 00 00 fd 00 32 4c 18
[ 0.377942] 5e 11 00 0a 20 20 20 20 20 20 00 00 00 fc 00 48
[ 0.377978] 50 20 4c 41 32 33 30 36 0a 20 20 00 00 00 ff 00
[ 0.378015] 43 4e 43 31 32 31 31 32 50 42 0a 20 20 00 5a 00
[ 0.395969] ------------[ cut here ]------------
[ 0.396007] WARNING: at drivers/gpu/drm/i915/intel_dp.c:410 intel_dp_aux_ch+0x131/0x4e0()
[ 0.396069] Hardware name: HP Compaq 8100 Elite SFF PC
[ 0.396104] dp_aux_ch not started status 0x8015003f
[ 0.396138] Modules linked in:
[ 0.396173] Pid: 6, comm: kworker/u:0 Not tainted 3.8.0-rc4-00071-g9a92841 #80
[ 0.396232] Call Trace:
[ 0.396268] [<ffffffff81036a29>] ? warn_slowpath_common+0x79/0xc0
[ 0.396306] [<ffffffff81036b25>] ? warn_slowpath_fmt+0x45/0x50
[ 0.396343] [<ffffffff812d7d61>] ? intel_dp_aux_ch+0x131/0x4e0
[ 0.396381] [<ffffffff812d82e2>] ? intel_dp_aux_native_write+0xa2/0xe0
[ 0.396421] [<ffffffff812da24f>] ? intel_dp_start_link_train+0x4f/0x2f0
[ 0.396460] [<ffffffff812da831>] ? intel_dp_check_link_status+0x91/0x180
[ 0.396504] [<ffffffff812a8bce>] ? i915_hotplug_work_func+0x6e/0xa0
[ 0.396543] [<ffffffff8104d1e0>] ? process_one_work+0x120/0x430
[ 0.396581] [<ffffffff812a8b60>] ? i915_error_work_func+0x100/0x100
[ 0.396620] [<ffffffff8104ef7d>] ? worker_thread+0x15d/0x450
[ 0.396658] [<ffffffff8104ee20>] ? schedule_delayed_work+0x20/0x20
[ 0.396698] [<ffffffff81053ca3>] ? kthread+0xb3/0xc0
[ 0.396734] [<ffffffff81053bf0>] ? kthread_create_on_node+0x110/0x110
[ 0.397269] [<ffffffff8145a7ec>] ? ret_from_fork+0x7c/0xb0
[ 0.397306] [<ffffffff81053bf0>] ? kthread_create_on_node+0x110/0x110
[ 0.397348] ---[ end trace 872ab3aea478e207 ]---
[ 0.397383] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.405066] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 0.405086] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[ 0.405099] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:14:DP-1] probed modes :
[ 0.405100] [drm:drm_mode_debug_printmodeline], Modeline 16:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.405102] [drm:drm_mode_debug_printmodeline], Modeline 20:"1680x1050" 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6
[ 0.405104] [drm:drm_mode_debug_printmodeline], Modeline 47:"1680x945" 60 131481 1680 1784 1960 2240 945 946 949 978 0x0 0x6
[ 0.405105] [drm:drm_mode_debug_printmodeline], Modeline 42:"1400x1050" 75 156000 1400 1504 1648 1896 1050 1053 1057 1099 0x40 0x6
[ 0.405107] [drm:drm_mode_debug_printmodeline], Modeline 41:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x40 0x6
[ 0.405109] [drm:drm_mode_debug_printmodeline], Modeline 46:"1600x900" 60 118963 1600 1696 1864 2128 900 901 904 932 0x0 0x6
[ 0.405110] [drm:drm_mode_debug_printmodeline], Modeline 39:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 0.405112] [drm:drm_mode_debug_printmodeline], Modeline 18:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 0.405114] [drm:drm_mode_debug_printmodeline], Modeline 43:"1440x900" 75 136750 1440 1536 1688 1936 900 903 909 942 0x40 0x6
[ 0.405115] [drm:drm_mode_debug_printmodeline], Modeline 19:"1440x900" 60 106500 1440 1520 1672 1904 900 903 909 934 0x40 0x6
[ 0.405117] [drm:drm_mode_debug_printmodeline], Modeline 38:"1280x960" 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
[ 0.405119] [drm:drm_mode_debug_printmodeline], Modeline 45:"1366x768" 60 85885 1366 1439 1583 1800 768 769 772 795 0x0 0x6
[ 0.405120] [drm:drm_mode_debug_printmodeline], Modeline 40:"1360x768" 60 85500 1360 1424 1536 1792 768 771 777 795 0x40 0x5
[ 0.405122] [drm:drm_mode_debug_printmodeline], Modeline 37:"1280x800" 75 106500 1280 1360 1488 1696 800 803 809 838 0x40 0x6
[ 0.405124] [drm:drm_mode_debug_printmodeline], Modeline 36:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x9
[ 0.405126] [drm:drm_mode_debug_printmodeline], Modeline 33:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[ 0.405127] [drm:drm_mode_debug_printmodeline], Modeline 35:"1280x768" 75 102250 1280 1360 1488 1696 768 771 778 805 0x40 0x9
[ 0.405129] [drm:drm_mode_debug_printmodeline], Modeline 34:"1280x768" 60 79500 1280 1344 1472 1664 768 771 778 798 0x40 0x6
[ 0.405131] [drm:drm_mode_debug_printmodeline], Modeline 17:"1280x720" 60 74440 1280 1336 1472 1664 720 721 724 746 0x0 0x6
[ 0.405133] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[ 0.405134] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
[ 0.405136] [drm:drm_mode_debug_printmodeline], Modeline 24:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[ 0.405138] [drm:drm_mode_debug_printmodeline], Modeline 44:"1024x576" 60 46970 1024 1064 1168 1312 576 577 580 597 0x0 0x6
[ 0.405139] [drm:drm_mode_debug_printmodeline], Modeline 28:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[ 0.405141] [drm:drm_mode_debug_printmodeline], Modeline 29:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[ 0.405143] [drm:drm_mode_debug_printmodeline], Modeline 21:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[ 0.405144] [drm:drm_mode_debug_printmodeline], Modeline 27:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[ 0.405146] [drm:drm_mode_debug_printmodeline], Modeline 30:"848x480" 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
[ 0.405148] [drm:drm_mode_debug_printmodeline], Modeline 26:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[ 0.405149] [drm:drm_mode_debug_printmodeline], Modeline 25:"640x480" 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
[ 0.405151] [drm:drm_mode_debug_printmodeline], Modeline 22:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[ 0.405153] [drm:drm_mode_debug_printmodeline], Modeline 23:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 0.405155] [drm:drm_setup_crtcs],
[ 0.405156] [drm:drm_enable_connectors], connector 7 enabled? no
[ 0.405157] [drm:drm_enable_connectors], connector 10 enabled? no
[ 0.405158] [drm:drm_enable_connectors], connector 14 enabled? yes
[ 0.405159] [drm:drm_target_preferred], looking for cmdline mode on connector 14
[ 0.405160] [drm:drm_target_preferred], looking for preferred mode on connector 14
[ 0.405161] [drm:drm_target_preferred], found mode 1920x1080
[ 0.405162] [drm:drm_setup_crtcs], picking CRTCs for 8192x8192 config
[ 0.405163] [drm:drm_setup_crtcs], desired mode 1920x1080 set on crtc 3
[ 0.412639] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.417632] [drm:intelfb_create], allocated 1920x1080 fb: 0x00047000, bo ffff880112e3c200
[ 0.417666] fbcon: inteldrmfb (fb0) is primary device
[ 0.419730] [drm:intel_dp_link_down],
[ 0.444025] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.444740] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.451823] [drm:intel_dp_link_down],
[ 0.479915] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.480631] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.487713] [drm:intel_dp_link_down],
[ 0.515806] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.516521] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.523604] [drm:intel_dp_link_down],
[ 0.551696] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.552412] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.559495] [drm:intel_dp_link_down],
[ 0.587587] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.588303] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.595386] [drm:intel_dp_link_down],
[ 0.623478] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 0.624193] [drm:intel_dp_start_link_train], clock recovery OK
[ 0.624194] [drm:intel_dp_complete_link_train] *ERROR* failed to train DP, aborting
[ 0.624195] [drm:intel_dp_link_down],
[ 0.651397] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 0.651398] [drm:intel_set_config_compute_mode_changes], crtc has no fb, full mode set
[ 0.651399] [drm:intel_set_config_compute_mode_changes], modes are different, full mode set
[ 0.651401] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
[ 0.651402] [drm:drm_mode_debug_printmodeline], Modeline 48:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.651404] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 0.651404] [drm:intel_crtc_set_config], attempting to set mode from userspace
[ 0.651406] [drm:drm_mode_debug_printmodeline], Modeline 48:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.651407] [drm:intel_set_mode], set mode pipe masks: modeset: 1, prepare: 1, disable: 0
[ 0.651409] [drm:intel_dp_mode_fixup], DP link computation with max lane count 4 max bw 06 pixel clock 148500KHz
[ 0.651410] [drm:intel_dp_mode_fixup], DP link bw 06 lane count 4 clock 162000 bpp 24
[ 0.651411] [drm:intel_dp_mode_fixup], DP link bw required 356400 available 518400
[ 0.651411] [drm:intel_modeset_adjusted_mode], [CRTC:3]
[ 0.651619] [drm:intel_dp_link_down],
[ 0.782787] ------------[ cut here ]------------
[ 0.782792] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 ironlake_crtc_disable+0xb1/0x860()
[ 0.782792] Hardware name: HP Compaq 8100 Elite SFF PC
[ 0.782793] pipe_off wait timed out
[ 0.782793] Modules linked in:
[ 0.782795] Pid: 1, comm: swapper/0 Tainted: G W 3.8.0-rc4-00071-g9a92841 #80
[ 0.782795] Call Trace:
[ 0.782800] [<ffffffff81036a29>] ? warn_slowpath_common+0x79/0xc0
[ 0.782801] [<ffffffff81036b25>] ? warn_slowpath_fmt+0x45/0x50
[ 0.782802] [<ffffffff812c6262>] ? intel_wait_for_pipe_off+0x62/0x170
[ 0.782803] [<ffffffff812c6bf1>] ? ironlake_crtc_disable+0xb1/0x860
[ 0.782806] [<ffffffff8128ee74>] ? drm_ut_debug_printk+0x44/0x70
[ 0.782807] [<ffffffff812cdf0e>] ? intel_set_mode+0x30e/0x900
[ 0.782809] [<ffffffff812cebe1>] ? intel_crtc_set_config+0x6e1/0x930
[ 0.782811] [<ffffffff814581b1>] ? __mutex_lock_slowpath+0xd1/0x140
[ 0.782813] [<ffffffff81282abf>] ? drm_fb_helper_set_par+0x6f/0xe0
[ 0.782816] [<ffffffff81216bdf>] ? fbcon_init+0x55f/0x5f0
[ 0.782819] [<ffffffff81266ddc>] ? visual_init+0xac/0x110
[ 0.782820] [<ffffffff8126863c>] ? bind_con_driver+0x16c/0x340
[ 0.782821] [<ffffffff81268870>] ? take_over_console+0x60/0x70
[ 0.782822] [<ffffffff81214f8b>] ? fbcon_takeover+0x5b/0xc0
[ 0.782825] [<ffffffff81059685>] ? notifier_call_chain+0x45/0x60
[ 0.782827] [<ffffffff81059865>] ? __blocking_notifier_call_chain+0x55/0x80
[ 0.782828] [<ffffffff8120e57f>] ? register_framebuffer+0x1af/0x2e0
[ 0.782829] [<ffffffff81282d24>] ? drm_fb_helper_single_fb_probe+0x1f4/0x330
[ 0.782830] [<ffffffff81283022>] ? drm_fb_helper_initial_config+0x1c2/0x220
[ 0.782832] [<ffffffff812eaa42>] ? intel_fbdev_init+0x32/0xb0
[ 0.782835] [<ffffffff810de64d>] ? __kmalloc+0xed/0x130
[ 0.782836] [<ffffffff812eaa8d>] ? intel_fbdev_init+0x7d/0xb0
[ 0.782838] [<ffffffff812a6f47>] ? i915_driver_load+0xbd7/0xdf0
[ 0.782840] [<ffffffff81291695>] ? drm_get_pci_dev+0x185/0x2c0
[ 0.782842] [<ffffffff811fbcb8>] ? pci_device_probe+0x98/0xe0
[ 0.782845] [<ffffffff812fde18>] ? driver_probe_device+0x68/0x220
[ 0.782846] [<ffffffff812fe063>] ? __driver_attach+0x93/0xa0
[ 0.782847] [<ffffffff812fdfd0>] ? driver_probe_device+0x220/0x220
[ 0.782848] [<ffffffff812fc2ad>] ? bus_for_each_dev+0x4d/0x80
[ 0.782849] [<ffffffff812fd588>] ? bus_add_driver+0x178/0x260
[ 0.782850] [<ffffffff812fe664>] ? driver_register+0x84/0x180
[ 0.782852] [<ffffffff8188dd1b>] ? drm_core_init+0x12f/0x12f
[ 0.782854] [<ffffffff810002e2>] ? do_one_initcall+0x122/0x170
[ 0.782857] [<ffffffff8186dba8>] ? kernel_init_freeable+0x102/0x192
[ 0.782858] [<ffffffff8186d54a>] ? do_early_param+0x83/0x83
[ 0.782860] [<ffffffff81446d00>] ? rest_init+0x70/0x70
[ 0.782860] [<ffffffff81446d09>] ? kernel_init+0x9/0xf0
[ 0.782862] [<ffffffff8145a7ec>] ? ret_from_fork+0x7c/0xb0
[ 0.782863] [<ffffffff81446d00>] ? rest_init+0x70/0x70
[ 0.782863] ---[ end trace 872ab3aea478e208 ]---
[ 0.838618] [drm:ironlake_disable_pch_transcoder] *ERROR* failed to disable transcoder 0
[ 0.838826] [drm:intel_choose_pipe_bpp_dither], clamping display bpc (was -1) to EDID reported max of 8
[ 0.838827] [drm:intel_choose_pipe_bpp_dither], setting pipe bpc to 8 (max display bpc 8)
[ 0.838828] [drm:ironlake_crtc_mode_set], Mode for pipe 0:
[ 0.838830] [drm:drm_mode_debug_printmodeline], Modeline 48:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 0.838831] [drm:intel_get_pch_pll], CRTC:3 using pre-allocated PCH PLL c6014
[ 0.838832] [drm:intel_get_pch_pll], using pll 0 for pipe 0
[ 0.838833] [drm:intel_get_pch_pll], switching PLL c6014 off
[ 0.839143] [drm:ironlake_check_fdi_lanes], checking fdi config on pipe 0, lanes 2
[ 0.894447] [drm:ironlake_wait_for_vblank], vblank wait timed out
[ 0.894450] [drm:ironlake_update_plane], Writing base 00047000 00000000 0 0 7680
[ 0.894454] [drm:intel_crtc_mode_set], [ENCODER:13:TMDS-13] set [MODE:48:1920x1080]
[ 0.894456] [drm:ironlake_update_wm], FIFO watermarks For pipe A - plane 9, cursor: 6
[ 0.894459] [drm:ironlake_check_srwm], watermark 1: display plane 91, fbc lines 3, cursor 6
[ 0.894460] [drm:ironlake_check_srwm], watermark 2: display plane 202, fbc lines 4, cursor 10
[ 0.950277] [drm:ironlake_wait_for_vblank], vblank wait timed out
[ 1.006107] [drm:ironlake_wait_for_vblank], vblank wait timed out
[ 1.006414] [drm:ironlake_fdi_link_train], FDI_RX_IIR 0x700
[ 1.006415] [drm:ironlake_fdi_link_train], FDI train 1 done.
[ 1.006567] [drm:ironlake_fdi_link_train], FDI_RX_IIR 0x600
[ 1.006569] [drm:ironlake_fdi_link_train], FDI train 2 done.
[ 1.006569] [drm:ironlake_fdi_link_train], FDI train done
[ 1.006570] [drm:ironlake_enable_pch_pll], enable PCH PLL c6014 (active 0, on? 0)for crtc 3
[ 1.006571] [drm:ironlake_enable_pch_pll], enabling PCH PLL c6014
[ 1.008189] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.008906] [drm:intel_dp_start_link_train], training pattern 1 signal levels 02000000
[ 1.009622] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.010339] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.011055] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.011772] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.012488] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.013204] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.013921] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.015141] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.015857] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.016574] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.017290] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.018006] [drm:intel_dp_start_link_train], training pattern 1 signal levels 02000000
[ 1.018723] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.019439] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.020156] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.020872] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.021588] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.022305] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.023021] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.024241] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.024957] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.025674] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.026391] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.027107] [drm:intel_dp_start_link_train], training pattern 1 signal levels 02000000
[ 1.027823] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.028540] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.029256] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.029972] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.030689] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.031405] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.032122] [drm:intel_dp_start_link_train], too many voltage retries, give up
[ 1.033341] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.034058] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.034774] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04400000
[ 1.035491] [drm:intel_dp_start_link_train], training pattern 1 signal levels 00000000
[ 1.036207] [drm:intel_dp_start_link_train], training pattern 1 signal levels 02000000
[ 1.036923] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.037639] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.038356] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.039072] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.039789] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.040505] [drm:intel_dp_start_link_train], training pattern 1 signal levels 04000000
[ 1.041221] [drm:intel_dp_start_link_train], clock recovery OK
[ 1.042234] [drm:intel_dp_complete_link_train], Channel EQ done. DP Training successfull
[ 1.065929] [drm:intel_connector_check_state], [CONNECTOR:14:DP-1]
[ 1.065930] [drm:intel_modeset_check_state], [ENCODER:8:DAC-8]
[ 1.065932] [drm:intel_modeset_check_state], [ENCODER:9:TMDS-9]
[ 1.065933] [drm:intel_modeset_check_state], [ENCODER:13:TMDS-13]
[ 1.065934] [drm:intel_modeset_check_state], [CRTC:3]
[ 1.065935] [drm:intel_modeset_check_state], [CRTC:5]
[ 1.065936] [drm:intel_crtc_set_config], [CRTC:5] [NOFB]
[ 1.065938] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 1.065956] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 1.065957] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 1.070039] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 1.070040] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 1.074095] Console: switching to colour frame buffer device 240x67
[ 1.074098] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 1.074099] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 1.088406] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 1.089577] i915 0000:00:02.0: registered panic notifier
[ 1.090802] ACPI Exception: AE_NOT_FOUND, Evaluating _DOD (20121018/video-1163)
[ 1.091998] ACPI: Video Device [GFX0] (multi-head: no rom: yes post: no)
[ 1.093214] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input2
[ 1.094440] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 1.095703] ahci 0000:00:1f.2: version 3.0
[ 1.095743] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
[ 1.095791] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x17 impl SATA mode
[ 1.097024] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part sxs apst
[ 1.098259] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.098570] scsi0 : ahci
[ 1.099846] scsi1 : ahci
[ 1.101104] scsi2 : ahci
[ 1.102362] scsi3 : ahci
[ 1.103610] scsi4 : ahci
[ 1.104843] scsi5 : ahci
[ 1.106063] ata1: SATA max UDMA/133 abar m2048 at 0xf0426000 port 0xf0426100 irq 41
[ 1.107288] ata2: SATA max UDMA/133 abar m2048 at 0xf0426000 port 0xf0426180 irq 41
[ 1.108502] ata3: SATA max UDMA/133 abar m2048 at 0xf0426000 port 0xf0426200 irq 41
[ 1.109696] ata4: DUMMY
[ 1.110889] ata5: SATA max UDMA/133 abar m2048 at 0xf0426000 port 0xf0426300 irq 41
[ 1.112098] ata6: DUMMY
[ 1.113342] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 1.117261] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.118519] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.119789] mousedev: PS/2 mouse device common for all mice
[ 1.121028] rtc_cmos 00:02: RTC can wake from S4
[ 1.122324] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.123564] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.124828] cpuidle: using governor ladder
[ 1.126099] cpuidle: using governor menu
[ 1.127386] TCP: cubic registered
[ 1.128668] NET: Registered protocol family 10
[ 1.130005] mip6: Mobile IPv6
[ 1.131235] NET: Registered protocol family 17
[ 1.132467] Key type dns_resolver registered
[ 1.133792] PM: Hibernation image not present or could not be loaded.
[ 1.133799] registered taskstats version 1
[ 1.135283] rtc_cmos 00:02: setting system clock to 2013-01-21 09:20:46 UTC (1358760046)
[ 1.225508] tsc: Refined TSC clocksource calibration: 3325.374 MHz
[ 1.226823] Switching to clocksource tsc
[ 1.428896] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.430724] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.432002] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.433801] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.435212] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.436495] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.437824] ata2.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.439557] ata2.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.441270] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.442967] ata2.00: ATAPI: hp CDDVDW TS-H653T, H6D1, max UDMA/100
[ 1.444677] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 1.444887] ata1.00: ACPI cmd e3/00:00:00:00:00:a0 (IDLE) succeeded
[ 1.444894] ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.446242] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.447529] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.449844] ata1.00: ATA-8: Hitachi HDS721025CLA682, JP1OA41A, max UDMA/133
[ 1.451203] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.452567] ata2.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.454443] ata2.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.456223] ata2.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.458038] ata2.00: configured for UDMA/100
[ 1.459811] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.460915] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1.462263] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1.463795] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 1.464012] ata1.00: ACPI cmd e3/00:00:00:00:00:a0 (IDLE) succeeded
[ 1.464018] ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.465471] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1.466838] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.469390] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.469397] ata1.00: configured for UDMA/133
[ 1.471047] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72102 JP1O PQ: 0 ANSI: 5
[ 1.472662] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.474141] sd 0:0:0:0: [sda] Write Protect is off
[ 1.474441] scsi 1:0:0:0: CD-ROM hp CDDVDW TS-H653T H6D1 PQ: 0 ANSI: 5
[ 1.477020] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.477035] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.522753] sda: sda1 sda2 < sda5 >
[ 1.524333] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.597567] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 1.598998] VFS: Mounted root (ext4 filesystem) readonly on device 8:1.
[ 1.600897] Freeing unused kernel memory: 492k freed
[ 1.602365] Write protecting the kernel read-only data: 8192k
[ 1.606503] Freeing unused kernel memory: 1660k freed
[ 1.609246] Freeing unused kernel memory: 668k freed
[ 4.433441] microcode: CPU0 sig=0x20655, pf=0x2, revision=0x2
[ 4.489234] processor LNXCPU:00: Invalid PBLK length [7]
[ 4.490743] ACPI: Requesting acpi_cpufreq
[ 4.492392] processor LNXCPU:01: Invalid PBLK length [7]
[ 4.493931] processor LNXCPU:02: Invalid PBLK length [7]
[ 4.495356] processor LNXCPU:03: Invalid PBLK length [7]
[ 4.612786] mei 0000:00:16.0: setting latency timer to 64
[ 4.612840] mei 0000:00:16.0: irq 42 for MSI/MSI-X
[ 4.615607] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
[ 4.617060] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 4.618489] e1000e 0000:00:19.0: setting latency timer to 64
[ 4.618530] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 4.620039] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 4.658631] microcode: CPU0 updated to revision 0x3, date = 2011-09-01
[ 4.660089] microcode: CPU1 sig=0x20655, pf=0x2, revision=0x2
[ 4.661685] microcode: CPU1 updated to revision 0x3, date = 2011-09-01
[ 4.663138] microcode: CPU2 sig=0x20655, pf=0x2, revision=0x2
[ 4.664702] microcode: CPU2 updated to revision 0x3, date = 2011-09-01
[ 4.666150] microcode: CPU3 sig=0x20655, pf=0x2, revision=0x2
[ 4.668144] microcode: CPU3 updated to revision 0x3, date = 2011-09-01
[ 4.669969] microcode: Microcode Update Driver: v2.00 <tigran at aivazian.fsnet.co.uk>, Peter Oruba
[ 4.723888] wmi: Mapper loaded
[ 4.745733] ACPI: bus type usb registered
[ 4.747384] usbcore: registered new interface driver usbfs
[ 4.749198] usbcore: registered new interface driver hub
[ 4.751033] usbcore: registered new device driver usb
[ 4.762296] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.783967] parport_pc 00:06: reported by Plug and Play ACPI
[ 4.785445] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 4.814140] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 78:e3:b5:a0:e5:e4
[ 4.815590] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 4.817068] e1000e 0000:00:19.0 eth0: MAC: 9, PHY: 9, PBA No: A002FF-0FF
[ 4.837165] ehci-pci: EHCI PCI platform driver
[ 4.838703] ehci-pci 0000:00:1a.0: setting latency timer to 64
[ 4.838706] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 4.840168] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 4.841645] ehci-pci 0000:00:1a.0: debug port 2
[ 4.847031] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 4.847050] ehci-pci 0000:00:1a.0: irq 20, io mem 0xf0426800
[ 4.858377] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 4.859836] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.861270] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.862703] usb usb1: Product: EHCI Host Controller
[ 4.864130] usb usb1: Manufacturer: Linux 3.8.0-rc4-00071-g9a92841 ehci_hcd
[ 4.865562] usb usb1: SerialNumber: 0000:00:1a.0
[ 4.867110] hub 1-0:1.0: USB hub found
[ 4.868560] hub 1-0:1.0: 3 ports detected
[ 4.870125] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 4.870127] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 4.871604] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 4.873050] ehci-pci 0000:00:1d.0: debug port 2
[ 4.878366] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 4.878372] ehci-pci 0000:00:1d.0: irq 20, io mem 0xf0426c00
[ 4.890312] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 4.891738] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.893146] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.894550] usb usb2: Product: EHCI Host Controller
[ 4.895933] usb usb2: Manufacturer: Linux 3.8.0-rc4-00071-g9a92841 ehci_hcd
[ 4.897328] usb usb2: SerialNumber: 0000:00:1d.0
[ 4.898780] hub 2-0:1.0: USB hub found
[ 4.900131] hub 2-0:1.0: 3 ports detected
[ 4.978063] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 5.061758] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.063102] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.064482] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 5.070031] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.071524] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.105526] tpm_tis 00:09: 1.2 TPM (device-id 0xB, rev-id 16)
[ 5.133355] gpio_ich: GPIO from 180 to 255 on gpio_ich
[ 5.177452] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 5.257846] iTCO_vendor_support: vendor-support=0
[ 5.259481] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 5.260831] iTCO_wdt: Found a Q57 TCO device (Version=2, TCOBASE=0xf860)
[ 5.262234] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.309452] usb 1-1: New USB device found, idVendor=8087, idProduct=0020
[ 5.312285] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.315288] hub 1-1:1.0: USB hub found
[ 5.317083] hub 1-1:1.0: 6 ports detected
[ 5.368903] tpm_tis 00:09: TPM is disabled/deactivated (0x7)
[ 5.428687] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 5.560666] usb 2-1: New USB device found, idVendor=8087, idProduct=0020
[ 5.562074] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.563511] hub 2-1:1.0: USB hub found
[ 5.565100] hub 2-1:1.0: 8 ports detected
[ 5.640131] usb 1-1.1: new high-speed USB device number 3 using ehci-pci
[ 5.720890] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 5.732166] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2512
[ 5.734115] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.736353] hub 1-1.1:1.0: USB hub found
[ 5.737699] hub 1-1.1:1.0: 2 ports detected
[ 5.770138] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 5.811615] usb 1-1.2: new low-speed USB device number 4 using ehci-pci
[ 5.932899] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c30e
[ 5.934269] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.935548] usb 1-1.2: Product: HID compliant keyboard
[ 5.936801] usb 1-1.2: Manufacturer: Logitech
[ 5.954444] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 5.955866] input: HDA Intel MID Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 5.957169] input: HDA Intel MID Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 5.958482] input: HDA Intel MID Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 5.959823] input: HDA Intel MID Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 6.419587] usbcore: registered new interface driver usbhid
[ 6.420936] usbhid: USB HID core driver
[ 6.467576] input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input10
[ 6.468995] hid-generic 0003:046D:C30E.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:1a.0-1.2/input0
[ 6.473161] input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/input/input11
[ 6.474572] hid-generic 0003:046D:C30E.0002: input,hidraw1: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:1a.0-1.2/input1
[ 6.606068] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround
[ 8.039162] Adding 7532540k swap on /dev/sda5. Priority:-1 extents:1 across:7532540k
[ 8.066752] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 8.273258] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 8.651925] fuse init (API version 7.20)
[ 8.678872] loop: module loaded
[ 12.570033] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 12.670672] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[ 12.670791] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.942915] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 12.942921] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 16.105314] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 16.107067] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.456287] lp0: using parport0 (interrupt-driven).
[ 21.533384] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 21.533388] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 21.626686] [drm:i915_driver_open],
[ 21.626728] [drm:intel_crtc_set_config], [CRTC:3] [FB:49] #connectors=1 (x y) (0 0)
[ 21.626734] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 21.626737] [drm:intel_crtc_set_config], [CRTC:5] [NOFB]
[ 21.626740] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 21.626776] [drm:i915_driver_open],
[ 21.655271] [drm:drm_mode_getresources], CRTC[2] CONNECTORS[3] ENCODERS[3]
[ 21.655280] [drm:drm_mode_getresources], CRTC[2] CONNECTORS[3] ENCODERS[3]
[ 21.655332] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 21.655335] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 21.655337] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 21.655339] [drm:intel_crt_detect], CRT not detected via hotplug
[ 21.662892] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 21.662898] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.662901] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 21.662904] [drm:intel_gmbus_force_bit], enabling bit-banging on i915 gmbus vga. force bit now 1
[ 21.663226] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.663228] [drm:intel_gmbus_force_bit], disabling bit-banging on i915 gmbus vga. force bit now 0
[ 21.663230] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 21.663232] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 21.663237] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 21.663239] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 21.663242] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 21.663243] [drm:intel_crt_detect], CRT not detected via hotplug
[ 21.670841] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 21.670847] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.670850] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 21.670852] [drm:intel_gmbus_force_bit], enabling bit-banging on i915 gmbus vga. force bit now 1
[ 21.671173] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.671176] [drm:intel_gmbus_force_bit], disabling bit-banging on i915 gmbus vga. force bit now 0
[ 21.671178] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 21.671181] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 21.671240] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 21.671243] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 21.678814] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 21.678820] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 21.678824] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 21.678831] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 21.678834] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 21.686787] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 21.686790] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 21.686792] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 21.686826] [drm:drm_mode_getconnector], [CONNECTOR:14:?]
[ 21.686828] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:14:DP-1]
[ 21.687140] [drm:intel_dp_detect], DPCD: 11 06 84 01 00 00 01 00 02 02 06 00 00 00 00
[ 21.688166] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.715159] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.716193] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.743204] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.743278] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[ 21.743321] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:14:DP-1] probed modes :
[ 21.743322] [drm:drm_mode_debug_printmodeline], Modeline 16:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 21.743324] [drm:drm_mode_debug_printmodeline], Modeline 20:"1680x1050" 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6
[ 21.743326] [drm:drm_mode_debug_printmodeline], Modeline 47:"1680x945" 60 131481 1680 1784 1960 2240 945 946 949 978 0x0 0x6
[ 21.743327] [drm:drm_mode_debug_printmodeline], Modeline 42:"1400x1050" 75 156000 1400 1504 1648 1896 1050 1053 1057 1099 0x40 0x6
[ 21.743329] [drm:drm_mode_debug_printmodeline], Modeline 41:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x40 0x6
[ 21.743330] [drm:drm_mode_debug_printmodeline], Modeline 46:"1600x900" 60 118963 1600 1696 1864 2128 900 901 904 932 0x0 0x6
[ 21.743332] [drm:drm_mode_debug_printmodeline], Modeline 39:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 21.743334] [drm:drm_mode_debug_printmodeline], Modeline 18:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 21.743335] [drm:drm_mode_debug_printmodeline], Modeline 43:"1440x900" 75 136750 1440 1536 1688 1936 900 903 909 942 0x40 0x6
[ 21.743337] [drm:drm_mode_debug_printmodeline], Modeline 19:"1440x900" 60 106500 1440 1520 1672 1904 900 903 909 934 0x40 0x6
[ 21.743339] [drm:drm_mode_debug_printmodeline], Modeline 38:"1280x960" 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
[ 21.743340] [drm:drm_mode_debug_printmodeline], Modeline 45:"1366x768" 60 85885 1366 1439 1583 1800 768 769 772 795 0x0 0x6
[ 21.743342] [drm:drm_mode_debug_printmodeline], Modeline 40:"1360x768" 60 85500 1360 1424 1536 1792 768 771 777 795 0x40 0x5
[ 21.743344] [drm:drm_mode_debug_printmodeline], Modeline 37:"1280x800" 75 106500 1280 1360 1488 1696 800 803 809 838 0x40 0x6
[ 21.743345] [drm:drm_mode_debug_printmodeline], Modeline 36:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x9
[ 21.743347] [drm:drm_mode_debug_printmodeline], Modeline 33:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[ 21.743349] [drm:drm_mode_debug_printmodeline], Modeline 35:"1280x768" 75 102250 1280 1360 1488 1696 768 771 778 805 0x40 0x9
[ 21.743350] [drm:drm_mode_debug_printmodeline], Modeline 34:"1280x768" 60 79500 1280 1344 1472 1664 768 771 778 798 0x40 0x6
[ 21.743352] [drm:drm_mode_debug_printmodeline], Modeline 17:"1280x720" 60 74440 1280 1336 1472 1664 720 721 724 746 0x0 0x6
[ 21.743354] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[ 21.743355] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
[ 21.743357] [drm:drm_mode_debug_printmodeline], Modeline 24:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[ 21.743358] [drm:drm_mode_debug_printmodeline], Modeline 44:"1024x576" 60 46970 1024 1064 1168 1312 576 577 580 597 0x0 0x6
[ 21.743360] [drm:drm_mode_debug_printmodeline], Modeline 28:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[ 21.743362] [drm:drm_mode_debug_printmodeline], Modeline 29:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[ 21.743363] [drm:drm_mode_debug_printmodeline], Modeline 21:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[ 21.743365] [drm:drm_mode_debug_printmodeline], Modeline 27:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[ 21.743366] [drm:drm_mode_debug_printmodeline], Modeline 30:"848x480" 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
[ 21.743368] [drm:drm_mode_debug_printmodeline], Modeline 26:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[ 21.743370] [drm:drm_mode_debug_printmodeline], Modeline 25:"640x480" 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
[ 21.743371] [drm:drm_mode_debug_printmodeline], Modeline 22:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[ 21.743373] [drm:drm_mode_debug_printmodeline], Modeline 23:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 21.743381] [drm:drm_mode_getconnector], [CONNECTOR:14:?]
[ 21.743421] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 21.743422] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 21.743424] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 21.743425] [drm:intel_crt_detect], CRT not detected via hotplug
[ 21.750616] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 21.750622] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.750625] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 21.750627] [drm:intel_gmbus_force_bit], enabling bit-banging on i915 gmbus vga. force bit now 1
[ 21.750944] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.750945] [drm:intel_gmbus_force_bit], disabling bit-banging on i915 gmbus vga. force bit now 0
[ 21.750947] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 21.750948] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 21.750950] [drm:drm_mode_getconnector], [CONNECTOR:7:?]
[ 21.750952] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1]
[ 21.750953] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0
[ 21.750954] [drm:intel_crt_detect], CRT not detected via hotplug
[ 21.758583] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1)
[ 21.758588] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.758591] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging
[ 21.758593] [drm:intel_gmbus_force_bit], enabling bit-banging on i915 gmbus vga. force bit now 1
[ 21.758910] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[ 21.758911] [drm:intel_gmbus_force_bit], disabling bit-banging on i915 gmbus vga. force bit now 0
[ 21.758912] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[ 21.758913] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:VGA-1] disconnected
[ 21.758955] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 21.758957] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 21.766597] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 21.766604] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 21.766608] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 21.766615] [drm:drm_mode_getconnector], [CONNECTOR:10:?]
[ 21.766619] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1]
[ 21.774543] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1)
[ 21.774548] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc
[ 21.774552] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:10:HDMI-A-1] disconnected
[ 21.774596] [drm:drm_mode_getconnector], [CONNECTOR:14:?]
[ 21.774600] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:14:DP-1]
[ 21.774912] [drm:intel_dp_detect], DPCD: 11 06 84 01 00 00 01 00 02 02 06 00 00 00 00
[ 21.775940] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.803055] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.804095] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.831127] [drm:i2c_algo_dp_aux_xfer], dp_aux_xfer return 2
[ 21.831150] [drm:drm_edid_to_eld], ELD: no CEA Extension found
[ 21.831163] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:14:DP-1] probed modes :
[ 21.831165] [drm:drm_mode_debug_printmodeline], Modeline 16:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0x5
[ 21.831166] [drm:drm_mode_debug_printmodeline], Modeline 20:"1680x1050" 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6
[ 21.831168] [drm:drm_mode_debug_printmodeline], Modeline 47:"1680x945" 60 131481 1680 1784 1960 2240 945 946 949 978 0x0 0x6
[ 21.831170] [drm:drm_mode_debug_printmodeline], Modeline 42:"1400x1050" 75 156000 1400 1504 1648 1896 1050 1053 1057 1099 0x40 0x6
[ 21.831171] [drm:drm_mode_debug_printmodeline], Modeline 41:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x40 0x6
[ 21.831173] [drm:drm_mode_debug_printmodeline], Modeline 46:"1600x900" 60 118963 1600 1696 1864 2128 900 901 904 932 0x0 0x6
[ 21.831174] [drm:drm_mode_debug_printmodeline], Modeline 39:"1280x1024" 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 21.831176] [drm:drm_mode_debug_printmodeline], Modeline 18:"1280x1024" 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
[ 21.831178] [drm:drm_mode_debug_printmodeline], Modeline 43:"1440x900" 75 136750 1440 1536 1688 1936 900 903 909 942 0x40 0x6
[ 21.831179] [drm:drm_mode_debug_printmodeline], Modeline 19:"1440x900" 60 106500 1440 1520 1672 1904 900 903 909 934 0x40 0x6
[ 21.831181] [drm:drm_mode_debug_printmodeline], Modeline 38:"1280x960" 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
[ 21.831182] [drm:drm_mode_debug_printmodeline], Modeline 45:"1366x768" 60 85885 1366 1439 1583 1800 768 769 772 795 0x0 0x6
[ 21.831184] [drm:drm_mode_debug_printmodeline], Modeline 40:"1360x768" 60 85500 1360 1424 1536 1792 768 771 777 795 0x40 0x5
[ 21.831186] [drm:drm_mode_debug_printmodeline], Modeline 37:"1280x800" 75 106500 1280 1360 1488 1696 800 803 809 838 0x40 0x6
[ 21.831187] [drm:drm_mode_debug_printmodeline], Modeline 36:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x9
[ 21.831189] [drm:drm_mode_debug_printmodeline], Modeline 33:"1152x864" 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5
[ 21.831191] [drm:drm_mode_debug_printmodeline], Modeline 35:"1280x768" 75 102250 1280 1360 1488 1696 768 771 778 805 0x40 0x9
[ 21.831192] [drm:drm_mode_debug_printmodeline], Modeline 34:"1280x768" 60 79500 1280 1344 1472 1664 768 771 778 798 0x40 0x6
[ 21.831194] [drm:drm_mode_debug_printmodeline], Modeline 17:"1280x720" 60 74440 1280 1336 1472 1664 720 721 724 746 0x0 0x6
[ 21.831195] [drm:drm_mode_debug_printmodeline], Modeline 32:"1024x768" 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5
[ 21.831197] [drm:drm_mode_debug_printmodeline], Modeline 31:"1024x768" 70 75000 1024 1048 1184 1328 768 771 777 806 0x40 0xa
[ 21.831199] [drm:drm_mode_debug_printmodeline], Modeline 24:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[ 21.831200] [drm:drm_mode_debug_printmodeline], Modeline 44:"1024x576" 60 46970 1024 1064 1168 1312 576 577 580 597 0x0 0x6
[ 21.831202] [drm:drm_mode_debug_printmodeline], Modeline 28:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[ 21.831203] [drm:drm_mode_debug_printmodeline], Modeline 29:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[ 21.831205] [drm:drm_mode_debug_printmodeline], Modeline 21:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[ 21.831207] [drm:drm_mode_debug_printmodeline], Modeline 27:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[ 21.831208] [drm:drm_mode_debug_printmodeline], Modeline 30:"848x480" 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
[ 21.831210] [drm:drm_mode_debug_printmodeline], Modeline 26:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[ 21.831211] [drm:drm_mode_debug_printmodeline], Modeline 25:"640x480" 73 31500 640 664 704 832 480 489 492 520 0x40 0xa
[ 21.831213] [drm:drm_mode_debug_printmodeline], Modeline 22:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[ 21.831214] [drm:drm_mode_debug_printmodeline], Modeline 23:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[ 21.831219] [drm:drm_mode_getconnector], [CONNECTOR:14:?]
[ 21.964052] [drm:drm_mode_addfb], [FB:50]
[ 21.964194] [drm:drm_mode_setcrtc], [CRTC:3]
[ 21.964196] [drm:drm_mode_setcrtc], [CONNECTOR:14:DP-1]
[ 21.964198] [drm:intel_crtc_set_config], [CRTC:3] [FB:50] #connectors=1 (x y) (0 0)
[ 21.964200] [drm:intel_modeset_stage_output_state], [CONNECTOR:14:DP-1] to [CRTC:3]
[ 21.975707] [drm:ironlake_update_plane], Writing base 00830000 00000000 0 0 7680
--
Meelis Roos (mroos at ut.ee) http://www.cs.ut.ee/~mroos/
More information about the dri-devel
mailing list