gma500: display displaced vertically by a few lines
Holger Schurig
holgerschurig at gmail.com
Mon May 13 08:10:53 PDT 2013
Oops, I did mistype. I have an 8086:8108:
# lspci --n | head -n 2
00:00.0 Host bridge [0600]: Intel Corporation System Controller Hub
(SCH Poulsbo) [8086:8100] (rev 07)
00:02.0 VGA compatible controller [0300]: Intel Corporation System
Controller Hub (SCH Poulsbo) Graphics Controller [8086:8108] (rev 07)
Somehow I think that this is a kernel regression, because for Kernel
3.2.31 I've used xorg-server-video-fbdev and psb_gfx, and there it
worked correctly.
Unfortunately my kernel has around 32 quilt patches added (e.g.
aufs3), so it's not easy for me to do a bi-section.
2013/5/13 Patrik Jakobsson <patrik.r.jakobsson at gmail.com>:
> On Mon, May 13, 2013 at 3:02 PM, Holger Schurig <holgerschurig at gmail.com> wrote:
>> I installed xserver-xorg-video-modesettings (from Debian Wheezy) and also
>> updated xserver-core, -evdev, -vesa and -fbdev. The I started X11. Seems
>> that Debian doesn't yet contain the addition of the modesettings driver to
>> the auto-probed drivers, Xorg.0.log didn't contain a trace of modesettings.
>>
>> So I added
>>
>> Section "Device"
>> Identifier "gma"
>> Driver "modesetting"
>> BusID "pci:0:2:0
>> EndSection
>>
>> But then I get
>>
>> [ 4309.430] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
>> [ 4309.430] (--) using VT number 1
>>
>> [ 4309.463] (WW) Falling back to old probe method for modesetting
>> [ 4309.464] (II) UnloadModule: "modesetting"
>> [ 4309.464] (EE) Screen(s) found, but none have a usable configuration.
>> [ 4309.464]
>> Fatal server error:
>> [ 4309.464] no screens found
>>
>> So, I tried to add a screen, while grumbling "Since when do I need a
>> 'Screen' section in a modern xorg.conf again?":
>>
>> Section "Screen"
>> Identifier "800x600"
>> Device "Card0"
>> DefaultDepth 24
>> EndSection
>>
>> But X11 still says
>>
>> [ 4440.511] (EE) Screen(s) found, but none have a usable configuration.
>> [ 4440.511]
>> Fatal server error:
>> [ 4440.511] no screens found
>>
>> And of course, it's silent about WHAT exactly would constitute a usable
>> configuration.
>>
>> I tried 32 bits depth as well. I tried adding a subsection "Display". I
>> tried to stay calm ... but no success so far! :-)
>>
>>
>> BTW, I upgraded to kernel 3.9.2 for this.
>
> Hi
>
> Valid device id's for poulsbo are 8086:8108 and 8086:8109 so 8080:8101 is
> something else.
>
> You should be fine with just:
>
> Section "Device"
> Identifier "gma"
> Driver "modesetting"
> EndSection
>
> So there is something else going on. Can we get a full dmesg on 3.9.2 with
> drm.debug=0xf
>
> Thanks
> Patrik
-------------- next part --------------
Initializing cgroup subsys cpu
Linux version 3.9.2 (linux at me) (gcc version 4.6.3 (Debian 4.6.3-1) ) #1 SMP Mon May 13 16:59:08 CEST 2013
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Disabled fast string operations
e820: BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000003f66ffff] usable
BIOS-e820: [mem 0x000000003f670000-0x000000003f67ffff] reserved
BIOS-e820: [mem 0x000000003f680000-0x000000003f68dfff] ACPI data
BIOS-e820: [mem 0x000000003f68e000-0x000000003f6c7fff] ACPI NVS
BIOS-e820: [mem 0x000000003f6c8000-0x000000003f7fffff] reserved
BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
NX (Execute Disable) protection: active
DMI not present or invalid.
e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
e820: last_pfn = 0x3f670 max_arch_pfn = 0x1000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask 0C0000000 write-back
1 base 03F700000 mask 0FFF00000 uncachable
2 base 03F800000 mask 0FF800000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 1GB, type WB
reg 1, base: 1015MB, range: 1MB, type UC
reg 2, base: 1016MB, range: 8MB, type UC
total RAM covered: 1015M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 16M num_reg: 3 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 1GB, type WB
reg 1, base: 1015MB, range: 1MB, type UC
reg 2, base: 1016MB, range: 8MB, type UC
found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [c00ff780]
initial memory mapped: [mem 0x00000000-0x019fffff]
Base memory trampoline at [c009b000] 9b000 size 16384
init_memory_mapping: [mem 0x00000000-0x000fffff]
[mem 0x00000000-0x000fffff] page 4k
init_memory_mapping: [mem 0x37800000-0x379fffff]
[mem 0x37800000-0x379fffff] page 2M
init_memory_mapping: [mem 0x34000000-0x377fffff]
[mem 0x34000000-0x377fffff] page 2M
init_memory_mapping: [mem 0x00100000-0x33ffffff]
[mem 0x00100000-0x001fffff] page 4k
[mem 0x00200000-0x33ffffff] page 2M
init_memory_mapping: [mem 0x37a00000-0x37bfdfff]
[mem 0x37a00000-0x37bfdfff] page 4k
BRK [0x01500000, 0x01500fff] PGTABLE
ACPI: RSDP 000f85f0 00024 (v02 ACPIAM)
ACPI: XSDT 3f680100 00064 (v01 MEIN Terminal 20090917 MSFT 00000097)
ACPI: FACP 3f680290 000F4 (v04 091709 FACP1631 20090917 MSFT 00000097)
ACPI: DSDT 3f6805c0 05E50 (v02 QMENR QMENR114 00000114 INTL 20051117)
ACPI: FACS 3f68e000 00040
ACPI: APIC 3f680390 00068 (v02 091709 APIC1631 20090917 MSFT 00000097)
ACPI: MCFG 3f680400 0003C (v01 091709 OEMMCFG 20090917 MSFT 00000097)
ACPI: SLIC 3f680440 00176 (v01 MEIN Terminal 20090917 MSFT 00000097)
ACPI: OEMB 3f68e040 0013C (v01 091709 OEMB1631 20090917 MSFT 00000097)
ACPI: HPET 3f686410 00038 (v01 091709 OEMHPET 20090917 MSFT 00000097)
ACPI: GSCI 3f68e180 02024 (v01 091709 GMCHSCI 20090917 MSFT 00000097)
ACPI: SSDT 3f690b70 004F0 (v01 PmRef CpuPm 00003000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
122MB HIGHMEM available.
891MB LOWMEM available.
mapped low ram: 0 - 37bfe000
low ram: 0 - 37bfe000
BRK [0x01501000, 0x01501fff] PGTABLE
Zone ranges:
DMA [mem 0x00001000-0x00ffffff]
Normal [mem 0x01000000-0x37bfdfff]
HighMem [mem 0x37bfe000-0x3f66ffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00001000-0x0009efff]
node 0: [mem 0x00100000-0x3f66ffff]
On node 0 totalpages: 259598
free_area_init_node: node 0, pgdat c140a440, node_mem_map f740e020
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3998 pages, LIFO batch:0
Normal zone: 1752 pages used for memmap
Normal zone: 224254 pages, LIFO batch:31
HighMem zone: 245 pages used for memmap
HighMem zone: 31346 pages, LIFO batch:7
Using APIC driver default
ACPI: PM-Timer IO Port: 0x908
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
smpboot: Allowing 1 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
e820: [mem 0x3f800000-0xfedfffff] available for PCI devices
setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Embedded 13 pages/cpu @f73fb000 s30400 r0 d22848 u53248
pcpu-alloc: s30400 r0 d22848 u53248 alloc=13*4096
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257814
Kernel command line: BOOT_IMAGE=/boot/vmlinuz root=/dev/sda1 ro quiet init=/bin/systemd drm.debug=0xf
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
__ex_table already sorted, skipping sort
Initializing CPU#0
Initializing HighMem for node 0 (00037bfe:0003f670)
Memory: 1024192k/1038784k available (2900k kernel code, 14200k reserved, 1272k data, 396k init, 125384k highmem)
virtual kernel memory layout:
fixmap : 0xfff67000 - 0xfffff000 ( 608 kB)
pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
.init : 0xc1414000 - 0xc1477000 ( 396 kB)
.data : 0xc12d508c - 0xc14131c0 (1272 kB)
.text : 0xc1000000 - 0xc12d508c (2900 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
NR_IRQS:2304 nr_irqs:256 16
CPU 0 irqstacks, hard=f6c08000 soft=f6c0a000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
tsc: Fast TSC calibration using PIT
tsc: Detected 1097.251 MHz processor
Calibrating delay loop (skipped), value calculated using timer frequency.. 2194.50 BogoMIPS (lpj=4389004)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Disabled fast string operations
mce: CPU supports 5 MCE banks
CPU0: Thermal monitoring enabled (TM1)
Last level iTLB entries: 4KB 32, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8
tlb_flushall_shift: 6
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20130117
ACPI: All ACPI Tables successfully acquired
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
smpboot: CPU0: Intel(R) Atom(TM) CPU Z510 @ 1.10GHz (fam: 06, model: 1c, stepping: 02)
Performance Events: PEBS fmt0+, LBR disabled due to erratumAtom events, Intel PMU driver.
... version: 3
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
Brought up 1 CPUs
smpboot: Total of 1 processors activated (2194.50 BogoMIPS)
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type PCI registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI : PCI BIOS area is rw and x. Use pci=nobios if you want it NX.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI BIOS Bug: Warning: Incorrect checksum in table [OEMB] - 0x03, should be 0x53 (20130117/tbutils-324)
ACPI: SSDT 3f690280 001FA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 001FA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 3f690510 0065D (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 0065D (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
ACPI: Power Resource [FAN1] (on)
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: root bus resource [mem 0x3f800000-0xdfffffff]
pci_bus 0000:00: root bus resource [mem 0xf0000000-0xffffffff]
pci 0000:00:00.0: [8086:8100] type 00 class 0x060000
pci 0000:00:02.0: [8086:8108] type 00 class 0x030000
pci 0000:00:02.0: reg 10: [mem 0xfe980000-0xfe9fffff]
pci 0000:00:02.0: reg 14: [io 0xd880-0xd887]
pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 1c: [mem 0xfe940000-0xfe97ffff]
pci 0000:00:1b.0: [8086:811b] type 00 class 0x040300
pci 0000:00:1b.0: reg 10: [mem 0xfe938000-0xfe93bfff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot
pci 0000:00:1c.0: [8086:8110] type 01 class 0x060400
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: [8086:8112] type 01 class 0x060400
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: [8086:8114] type 00 class 0x0c0300
pci 0000:00:1d.0: reg 20: [io 0xd480-0xd49f]
pci 0000:00:1d.1: [8086:8115] type 00 class 0x0c0300
pci 0000:00:1d.1: reg 20: [io 0xd080-0xd09f]
pci 0000:00:1d.2: [8086:8116] type 00 class 0x0c0300
pci 0000:00:1d.2: reg 20: [io 0xc880-0xc89f]
pci 0000:00:1d.7: [8086:8117] type 00 class 0x0c0320
pci 0000:00:1d.7: reg 10: [mem 0xfe937c00-0xfe937fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.0: [8086:8119] type 00 class 0x060100
pci 0000:00:1f.1: [8086:811a] type 00 class 0x010180
pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
pci 0000:01:00.0: [168c:002a] type 00 class 0x028000
pci 0000:01:00.0: reg 10: [mem 0xfeaf0000-0xfeafffff 64bit]
pci 0000:01:00.0: supports D1
pci 0000:01:00.0: PME# supported from D0 D1 D3hot
pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.0: PCI bridge to [bus 01]
pci 0000:00:1c.0: bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
pci 0000:02:00.0: reg 10: [io 0xef00-0xefff]
pci 0000:02:00.0: reg 18: [mem 0xfebff000-0xfebfffff 64bit]
pci 0000:02:00.0: reg 20: [mem 0xcfff0000-0xcfffffff 64bit pref]
pci 0000:02:00.0: reg 30: [mem 0xfebc0000-0xfebdffff pref]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:1c.1: PCI bridge to [bus 02]
pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.1: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1c.1: bridge window [mem 0xcff00000-0xcfffffff pref]
pci_bus 0000:00: on NUMA node 0
acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
ACPI: Invalid _PRS IRQ 0
ACPI: PCI Interrupt Link [LNKC] (IRQs) *0, disabled.
ACPI: Invalid _PRS IRQ 0
ACPI: PCI Interrupt Link [LNKD] (IRQs) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs *5)
ACPI: PCI Interrupt Link [LNKF] (IRQs *15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 15) *6
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
ACPI: Enabled 3 GPEs in block 00 to 1F
acpi root: \_SB_.PCI0 notify handler is installed
Found 1 acpi root devices
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:00:02.0
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Initialized.
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
e820: reserve RAM buffer [mem 0x3f670000-0x3fffffff]
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type PNP registered
system 00:00: [mem 0x40000000-0x7fffffff] has been reserved
system 00:00: [mem 0x3f800000-0x3fffffff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
system 00:04: [io 0x04d0-0x04d1] has been reserved
system 00:04: [io 0x0900-0x09f3] has been reserved
system 00:04: [io 0x0400-0x043f] has been reserved
system 00:04: [io 0x0480-0x04bf] has been reserved
system 00:04: [mem 0xf0000000-0xf0003fff] has been reserved
system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:05: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:08: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:09: [io 0x0a00-0x0a7f] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0c: Plug and Play ACPI device, IDs PNP0400 (active)
system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:0e: [mem 0xe0000000-0xefffffff] has been reserved
system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:0f: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0f: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:0f: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0f: [mem 0x00100000-0x3f7fffff] could not be reserved
system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 16 devices
ACPI: bus type PNP unregistered
pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff pref] to [bus 01] add_size 200000
pci 0000:00:1c.0: res[9]=[mem 0x00100000-0x000fffff pref] get_res_add_size add_size 200000
pci 0000:00:1c.0: res[7]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
pci 0000:00:1c.0: BAR 9: assigned [mem 0x80000000-0x801fffff pref]
pci 0000:00:1c.0: BAR 7: assigned [io 0x1000-0x1fff]
pci 0000:00:1c.0: PCI bridge to [bus 01]
pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
pci 0000:00:1c.0: bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff pref]
pci 0000:00:1c.1: PCI bridge to [bus 02]
pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.1: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1c.1: bridge window [mem 0xcff00000-0xcfffffff pref]
pci 0000:00:1c.0: enabling device (0106 -> 0107)
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0x3f800000-0xdfffffff]
pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfeafffff]
pci_bus 0000:01: resource 2 [mem 0x80000000-0x801fffff pref]
pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
pci_bus 0000:02: resource 1 [mem 0xfeb00000-0xfebfffff]
pci_bus 0000:02: resource 2 [mem 0xcff00000-0xcfffffff pref]
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 32 bytes, default 64
bounce pool size: 64 pages
aufs 3.9-20130506
msgmni has been set to 1755
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered (default)
intel_idle: MWAIT substates: 0x3020220
intel_idle: v0.4 model 0x1C
intel_idle: lapic_timer_reliable_states 0x2
tsc: Marking TSC unstable due to TSC halts in idle states deeper than C2
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
ACPI: Sleep Button [SLPB]
ACPI: Requesting acpi_cpufreq
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (55 C)
Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Linux agpgart interface v0.103
loop: module loaded
pata_sch 0000:00:1f.1: version 0.2
pata_sch 0000:00:1f.1: setting latency timer to 64
scsi0 : pata_sch
scsi1 : pata_sch
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: irq 40 for MSI/MSI-X
r8169 0000:02:00.0 eth0: RTL8168c/8111c at 0xf8414000, 00:13:95:08:e4:20, XID 1c2000c0 IRQ 40
r8169 0000:02:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:1d.7: setting latency timer to 64
ehci-pci 0000:00:1d.7: EHCI Host Controller
ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:1d.7: debug port 1
ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
ehci-pci 0000:00:1d.7: irq 23, io mem 0xfe937c00
ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.9.2 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000d480
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 3.9.2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000d080
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 3.9.2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000c880
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 3.9.2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042: PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PC Speaker as /devices/platform/pcspkr/input/input2
rtc_cmos 00:01: RTC can wake from S4
rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Netfilter messages via NETLINK v0.30.
TCP: westwood registered
NET: Registered protocol family 17
Using IPI Shortcut mode
ALSA device list:
No soundcards found.
ata1.00: ATA-7: SFCA4096H1BR4TO-I-MS-226-STD, 20100806, max UDMA/133
ata1.00: 7793856 sectors, multi 0: LBA
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA SFCA4096H1BR4TO- 2010 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 7793856 512-byte logical blocks: (3.99 GB/3.71 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
EXT3-fs (sda1): recovery required on readonly filesystem
EXT3-fs (sda1): write access will be enabled during recovery
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda1): recovery complete
EXT3-fs (sda1): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
devtmpfs: mounted
Freeing unused kernel memory: 396k freed
Write protecting the kernel text: 2904k
Write protecting the kernel read-only data: 1016k
NX-protecting the kernel data: 3240k
systemd[1]: systemd 189 running in system mode. (-PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT -LIBCRYPTSETUP -GCRYPT -ACL +XZ; debian)
systemd[1]: [/lib/systemd/system/scannerd.service:3] Unknown lvalue 'Requist' in section 'Unit'. Ignoring.
systemd-udevd[44]: starting version 189
systemd-journald[45]: Fixed max_use=50.0M max_size=6.2M min_size=64.0K keep_free=25.0M
systemd-journald[45]: Reserving 11384 entries in hash table.
systemd-journald[45]: Vacuuming...
systemd-journald[45]: Flushing /dev/kmsg...
usb 2-2: new low-speed USB device number 2 using uhci_hcd
EXT3-fs (sda1): using internal journal
usb 2-2: New USB device found, idVendor=413c, idProduct=2107
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: Dell USB Entry Keyboard
usb 2-2: Manufacturer: DELL
input: DELL Dell USB Entry Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input3
hid-generic 0003:413C:2107.0001: input: USB HID v1.10 Keyboard [DELL Dell USB Entry Keyboard] on usb-0000:00:1d.0-2/input0
usb 4-2: new full-speed USB device number 2 using uhci_hcd
usb 4-2: New USB device found, idVendor=1a02, idProduct=bad6
usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: Environment Controller
input: Environment Controller as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input4
hid-generic 0003:1A02:BAD6.0002: input: USB HID v1.11 Keyboard [Environment Controller] on usb-0000:00:1d.2-2/input0
systemd-journald[45]: systemd-journald running as pid 45
systemd-journald[45]: Received SIGUSR1
[drm] Initialized drm 1.1.0 20060810
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5
[drm:drm_pci_init],
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[drm:drm_get_pci_dev],
[drm:drm_get_minor],
[drm:drm_get_minor], new minor assigned 64
[drm:drm_get_minor],
[drm:drm_get_minor], new minor assigned 0
gma500 0000:00:02.0: setting latency timer to 64
[drm:psb_intel_opregion_setup], OpRegion detected at 0x3f68e1a4
[drm:psb_intel_opregion_setup], Public ACPI methods supported
[drm:psb_intel_opregion_setup], ASLE supported
[drm:psb_intel_init_bios], Using VBT from OpRegion: $VBT POULSBO d
[drm:drm_mode_debug_printmodeline], Modeline 0:"800x600" 0 39790 800 824 896 1056 600 601 603 628 0x8 0xa
[drm:parse_sdvo_device_mapping], No SDVO device info is found in VBT
[drm:parse_edp], EDP timing in vbt t1_t3 32810 t8 162 t9 34014 t10 0 t11_t12 6144
[drm:parse_edp], VBT reports EDP: Lane_count 1, Lane_rate 6, Bpp 18
[drm:parse_edp], VBT reports EDP: VSwing 0, Preemph 0
[Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
acpi device:03: registered as cooling_device1
acpi device:04: registered as cooling_device2
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm:drm_irq_install], irq=16
[drm:drm_sysfs_connector_add], adding "LVDS-1" to sysfs
[drm:drm_sysfs_hotplug_event], generating hotplug event
[drm:psb_intel_sdvo_read_byte], i2c transfer returned -6
[drm:psb_intel_sdvo_init], No SDVO device found on SDVOB
[drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:LVDS-1]
[drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter intel drm LVDSBLC_B
[drm:drm_helper_probe_single_connector_modes], [CONNECTOR:7:LVDS-1] probed modes :
[drm:drm_mode_debug_printmodeline], Modeline 20:"800x600" 60 39790 800 824 896 1056 600 601 603 628 0x48 0xa
[drm:drm_mode_debug_printmodeline], Modeline 18:"800x600" 72 50000 800 856 976 1040 600 637 643 666 0x40 0x5
[drm:drm_mode_debug_printmodeline], Modeline 17:"800x600" 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5
[drm:drm_mode_debug_printmodeline], Modeline 11:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[drm:drm_mode_debug_printmodeline], Modeline 12:"800x600" 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
[drm:drm_mode_debug_printmodeline], Modeline 14:"640x480" 73 31500 640 664 704 832 480 489 491 520 0x40 0xa
[drm:drm_mode_debug_printmodeline], Modeline 13:"640x480" 75 31500 640 656 720 840 480 481 484 500 0x40 0xa
[drm:drm_mode_debug_printmodeline], Modeline 15:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[drm:drm_mode_debug_printmodeline], Modeline 16:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6
[drm:drm_setup_crtcs],
[drm:drm_enable_connectors], connector 7 enabled? yes
[drm:drm_target_preferred], looking for cmdline mode on connector 7
[drm:drm_target_preferred], looking for preferred mode on connector 7
[drm:drm_target_preferred], found mode 800x600
[drm:drm_setup_crtcs], picking CRTCs for 2048x2048 config
[drm:drm_setup_crtcs], desired mode 800x600 set on crtc 4
[drm:drm_framebuffer_reference], FB ID: 21
fbcon: psbfb (fb0) is primary device
[drm:drm_crtc_helper_set_config],
[drm:drm_crtc_helper_set_config], [CRTC:3] [NOFB]
[drm:drm_crtc_helper_set_config],
[drm:drm_crtc_helper_set_config], [CRTC:4] [FB:21] #connectors=1 (x y) (0 0)
[drm:drm_crtc_helper_set_config], crtc has no fb, full mode set
[drm:drm_crtc_helper_set_config], modes are different, full mode set
[drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
[drm:drm_mode_debug_printmodeline], Modeline 10:"800x600" 60 39790 800 824 896 1056 600 601 603 628 0x48 0xa
[drm:drm_crtc_helper_set_config], encoder changed, full mode switch
[drm:drm_crtc_helper_set_config], crtc changed, full mode switch
[drm:drm_crtc_helper_set_config], [CONNECTOR:7:LVDS-1] to [CRTC:4]
[drm:drm_crtc_helper_set_config], attempting to set mode from userspace
[drm:drm_mode_debug_printmodeline], Modeline 10:"800x600" 60 39790 800 824 896 1056 600 601 603 628 0x48 0xa
ath: EEPROM regdomain: 0x37
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: AW
ath: Regpair used: 0x37
[drm:drm_crtc_helper_set_mode], [CRTC:4]
[drm:drm_mode_debug_printmodeline], Modeline 10:"800x600" 60 39790 800 824 896 1056 600 601 603 628 0x48 0xa
[drm:drm_crtc_helper_set_mode], [ENCODER:8:LVDS-8] set [MODE:10:800x600]
[drm:drm_calc_timestamping_constants], crtc 4: hwmode: htotal 1056, vtotal 628, vdisplay 600
[drm:drm_calc_timestamping_constants], crtc 4: clock 39790 kHz framedur 16666700 linedur 26539, pixeldur 25
[drm:drm_crtc_helper_set_config], Setting connector DPMS state to on
[drm:drm_crtc_helper_set_config], [CONNECTOR:7:LVDS-1] set DPMS on
[drm:drm_framebuffer_reference], FB ID: 21
r8169 0000:02:00.0 eth0: link down
r8169 0000:02:00.0 eth0: link down
Console: switching to colour frame buffer device 100x37
gma500 0000:00:02.0: fb0: psbfb frame buffer device
gma500 0000:00:02.0: registered panic notifier
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
[drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
cdc_acm 4-2:1.1: ttyACM0: USB ACM device
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[drm:asle_set_backlight], asle set backlight 800000ff
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
[drm:asle_set_backlight], asle set backlight 800000ff
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
cfg80211: Calling CRDA for country: AW
cfg80211: Regulatory domain changed to country: AW
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf8560000, irq=16
[drm:asle_set_backlight], asle set backlight 800000ff
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
[drm:asle_set_backlight], asle set backlight 800000ff
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
gma500 0000:00:02.0: Backlight lvds set brightness 7a127a12
r8169 0000:02:00.0 eth0: link up
wlan0: authenticate with 74:31:70:4b:92:2e
wlan0: send auth to 74:31:70:4b:92:2e (try 1/3)
wlan0: authenticated
wlan0: associate with 74:31:70:4b:92:2e (try 1/3)
wlan0: RX AssocResp from 74:31:70:4b:92:2e (capab=0x411 status=0 aid=2)
wlan0: associated
More information about the dri-devel
mailing list