[PATCH 3/7] drm/panel: Add driver for exynos_dp based panels
Ajay kumar
ajaynumb at gmail.com
Fri Apr 18 12:42:37 PDT 2014
Hi Jingoo,
On Fri, Apr 18, 2014 at 2:17 PM, Jingoo Han <jg1.han at samsung.com> wrote:
> On Wednesday, April 16, 2014 11:33 PM, Ajay Kumar wrote:
> >
> > This patch adds a simple driver to handle all the LCD and LED
> > powerup/down routines needed to support eDP/eDP-LVDS panels
> > supported on exynos boards.
> >
> > Most of the eDP/LVDS panels need this sequence for powerup:
> > -- LCD unit powerup/LCD_EN
> > -- video data on
> > -- LED unit powerup/BL_EN
> >
> > The LCD and LED units are usually powered up via regulators,
> > and almost on all boards, we will have a BL_EN pin to enable/
> > disable the backlight. Sometimes, we can have LCD_EN switches
> > as well. The routines in this driver can be used to control
> > panel power sequence on such boards.
> >
> > Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
> > ---
> > .../devicetree/bindings/panel/exynos-dp-panel.txt | 32 ++++
> > drivers/gpu/drm/panel/Kconfig | 9 +
> > drivers/gpu/drm/panel/Makefile | 1 +
> > drivers/gpu/drm/panel/panel-exynos-dp.c | 213
> +++++++++++++++++++++
> > 4 files changed, 255 insertions(+)
> > create mode 100644
> Documentation/devicetree/bindings/panel/exynos-dp-panel.txt
> > create mode 100644 drivers/gpu/drm/panel/panel-exynos-dp.c
> >
> > diff --git a/Documentation/devicetree/bindings/panel/exynos-dp-panel.txt
> > b/Documentation/devicetree/bindings/panel/exynos-dp-panel.txt
> > new file mode 100644
> > index 0000000..a1428d2
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/panel/exynos-dp-panel.txt
> > @@ -0,0 +1,32 @@
> > +exynos_DP_panel/DP_to_LVDS_panel
>
> Please remove unnecessary under lines as below.
>
> Ok.
> Exynos DP panel/DP to LVDS panel
>
> > +==================================
> > +
> > +Required properties:
> > + - compatible: "samsung,exynos-dp-panel"
> > +
> > +Optional properties:
> > + -samsung,lcd-en-gpio:
> > + eDP panel LCD poweron GPIO.
> > + Indicates which GPIO needs to be powered up as
> output
> > + to powerup/enable the switch to the LCD panel.
> > + -samsung,led-en-gpio:
> > + eDP panel LED enable GPIO.
> > + Indicates which GPIO needs to be powered up as
> output
> > + to enable the backlight.
> > + -samsung,power-up-delay:
> > + eDP panel powerup delay value in ms.
> > + Delay in ms needed for the eDP panel to properly
> > + powerup after giving powerup signals to the panel.
> > + -samsung,power-down-delay:
> > + eDP panel powerdown delay value in ms.
> > + Delay in ms needed for the eDP panel to properly
> > + powerdown after giving powerdown signals to the
> panel.
> > +
> > +Example:
> > +
> > + dp-panel {
> > + compatible = "samsung,exynos-dp-panel";
> > + samsung,led-en-gpio = <&gpx3 0 1>;
> > + samsung,power-up-delay = <40>;
> > + samsung,power-down-delay = <50>;
> > + };
> > diff --git a/drivers/gpu/drm/panel/Kconfig
> b/drivers/gpu/drm/panel/Kconfig
> > index 4ec874d..ea9d5ac 100644
> > --- a/drivers/gpu/drm/panel/Kconfig
> > +++ b/drivers/gpu/drm/panel/Kconfig
> > @@ -30,4 +30,13 @@ config DRM_PANEL_S6E8AA0
> > select DRM_MIPI_DSI
> > select VIDEOMODE_HELPERS
> >
> > +config DRM_PANEL_EXYNOS_DP
> > + tristate "support for DP panels"
> > + depends on OF && DRM_PANEL && DRM_EXYNOS_DP
> > + help
> > + DRM panel driver for DP panels and LVDS connected via DP bridges
> > + that need at most a regulator for LCD unit, a regulator for LED
> unit
> > + and/or enable GPIOs for LCD or LED units. Delay values can also
> be
> > + specified to support powerup and powerdown process.
> > +
> > endmenu
> > diff --git a/drivers/gpu/drm/panel/Makefile
> b/drivers/gpu/drm/panel/Makefile
> > index 8b92921..30311a4 100644
> > --- a/drivers/gpu/drm/panel/Makefile
> > +++ b/drivers/gpu/drm/panel/Makefile
> > @@ -1,3 +1,4 @@
> > obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
> > obj-$(CONFIG_DRM_PANEL_LD9040) += panel-ld9040.o
> > obj-$(CONFIG_DRM_PANEL_S6E8AA0) += panel-s6e8aa0.o
> > +obj-$(CONFIG_DRM_PANEL_EXYNOS_DP) += panel-exynos-dp.o
> > diff --git a/drivers/gpu/drm/panel/panel-exynos-dp.c
> b/drivers/gpu/drm/panel/panel-exynos-dp.c
> > new file mode 100644
> > index 0000000..e85a7b2
> > --- /dev/null
> > +++ b/drivers/gpu/drm/panel/panel-exynos-dp.c
> > @@ -0,0 +1,213 @@
> > +/*
> > + * Exynos DP panel driver
> > + *
> > + * Copyright (c) 2014 Samsung Electronics Co., Ltd
> > + *
> > + * Ajay Kumar <ajaykumar.rs at samsung.com>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/component.h>
> > +#include <linux/gpio.h>
> > +#include <linux/module.h>
> > +#include <linux/of_gpio.h>
> > +#include <linux/of_platform.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_crtc.h>
> > +#include <drm/drm_panel.h>
> > +
> > +struct panel_exynos_dp {
> > + struct drm_panel base;
> > + struct regulator *bck_fet;
> > + struct regulator *lcd_fet;
>
> 'bck' means 'backlight'? Then, just use 'backlight_fet'.
>
backlight_fet is more meaningful. Will change it.
Also, I cannot understand the meaning of 'fet'.
> What's the meaning of the 'fet'?
>
> FET is an output from the regulator. On exynos5250-snow board,
FET1 controls power to the backlight unit.
See more here: https://lkml.org/lkml/2014/4/15/618
> + int led_en_gpio;
> > + int lcd_en_gpio;
> > + int power_up_delay;
> > + int power_down_delay;
> > + bool enabled;
> > +};
> > +
> > +static inline struct panel_exynos_dp *to_panel(struct drm_panel *panel)
> > +{
> > + return container_of(panel, struct panel_exynos_dp, base);
> > +}
> > +
> > +static int panel_exynos_dp_disable(struct drm_panel *panel)
> > +{
> > + struct panel_exynos_dp *dp_panel = to_panel(panel);
> > + bool enable_delay = false;
> > +
> > + if (!dp_panel->enabled)
> > + return 0;
> > +
> > + if (gpio_is_valid(dp_panel->led_en_gpio))
> > + gpio_set_value(dp_panel->led_en_gpio, 0);
> > +
> > + if (!IS_ERR_OR_NULL(dp_panel->bck_fet))
> > + regulator_disable(dp_panel->bck_fet);
> > +
> > + if (gpio_is_valid(dp_panel->lcd_en_gpio)) {
> > + gpio_set_value(dp_panel->lcd_en_gpio, 0);
> > + enable_delay = true;
> > + }
> > +
> > + if (!IS_ERR_OR_NULL(dp_panel->lcd_fet)) {
> > + regulator_disable(dp_panel->lcd_fet);
> > + enable_delay = true;
> > + }
> > +
> > + if (enable_delay)
> > + msleep(dp_panel->power_down_delay);
> > +
> > + dp_panel->enabled = false;
> > +
> > + return 0;
> > +}
> > +
> > +static int panel_exynos_dp_pre_enable(struct drm_panel *panel)
>
> panel_exynos_dp_pre_enable() always returns '0'.
> These are two ways. Either one will be better.
> 1. Make return values meaningful. In other words, add the case
> returning error values.
>
> 2. Change the return type to 'void'
>
> Ok. Will add a check for all failure cases.
> > +{
> > + struct panel_exynos_dp *dp_panel = to_panel(panel);
> > + bool enable_delay = false;
> > +
> > + if (dp_panel->enabled)
> > + return 0;
> > +
> > + if (!IS_ERR_OR_NULL(dp_panel->lcd_fet)) {
> > + if (regulator_enable(dp_panel->lcd_fet))
> > + DRM_ERROR("Failed to enable LCD fet\n");
> > + enable_delay = true;
> > + }
> > +
> > + if (gpio_is_valid(dp_panel->lcd_en_gpio)) {
> > + gpio_set_value(dp_panel->lcd_en_gpio, 1);
> > + enable_delay = true;
> > + }
> > +
> > + if (enable_delay)
> > + msleep(dp_panel->power_up_delay);
> > +
> > + return 0;
> > +}
> > +
> > +static int panel_exynos_dp_enable(struct drm_panel *panel)
> > +{
> > + struct panel_exynos_dp *dp_panel = to_panel(panel);
> > +
> > + if (dp_panel->enabled)
> > + return 0;
> > +
> > + if (!IS_ERR_OR_NULL(dp_panel->bck_fet))
> > + if (regulator_enable(dp_panel->bck_fet))
> > + DRM_ERROR("Failed to enable LED fet\n");
> > +
> > + if (gpio_is_valid(dp_panel->led_en_gpio))
> > + gpio_set_value(dp_panel->led_en_gpio, 1);
> > +
> > + dp_panel->enabled = true;
> > +
> > + return 0;
> > +}
> > +
> > +static const struct drm_panel_funcs panel_exynos_dp_funcs = {
> > + .disable = panel_exynos_dp_disable,
> > + .pre_enable = panel_exynos_dp_pre_enable,
> > + .enable = panel_exynos_dp_enable,
> > +};
> > +
> > +static int panel_exynos_dp_probe(struct platform_device *pdev)
> > +{
> > + struct panel_exynos_dp *dp_panel;
> > + struct device *dev = &pdev->dev;
> > + int ret;
> > +
> > + dp_panel = devm_kzalloc(dev, sizeof(*dp_panel), GFP_KERNEL);
> > + if (!dp_panel)
> > + return -ENOMEM;
> > +
> > + dp_panel->enabled = false;
> > +
> > + dp_panel->lcd_en_gpio = of_get_named_gpio(dev->of_node,
> > + "samsung,lcd-en-gpio", 0);
> > + dp_panel->led_en_gpio = of_get_named_gpio(dev->of_node,
> > + "samsung,led-en-gpio", 0);
> > +
> > + of_property_read_u32(dev->of_node, "samsung,power-up-delay",
> > + &dp_panel->power_up_delay);
> > + of_property_read_u32(dev->of_node, "samsung,power-down-delay",
> > +
> &dp_panel->power_down_delay);
> > +
> > + dp_panel->lcd_fet = devm_regulator_get(dev, "lcd_vdd");
> > + if (IS_ERR(dp_panel->lcd_fet))
> > + return PTR_ERR(dp_panel->lcd_fet);
> > +
> > + dp_panel->bck_fet = devm_regulator_get(dev, "vcd_led");
> > + if (IS_ERR(dp_panel->bck_fet))
> > + return PTR_ERR(dp_panel->bck_fet);
> > +
> > + if (gpio_is_valid(dp_panel->lcd_en_gpio)) {
> > + ret = devm_gpio_request_one(dev, dp_panel->lcd_en_gpio,
> > + GPIOF_OUT_INIT_LOW, "lcd_en_gpio");
> > + if (ret) {
> > + DRM_ERROR("failed to get lcd-en gpio [%d]\n", ret);
> > + return ret;
> > + }
> > + } else {
> > + dp_panel->lcd_en_gpio = -ENODEV;
> > + }
> > +
> > + if (gpio_is_valid(dp_panel->led_en_gpio)) {
> > + ret = devm_gpio_request_one(dev, dp_panel->led_en_gpio,
> > + GPIOF_OUT_INIT_LOW, "led_en_gpio");
> > + if (ret) {
> > + DRM_ERROR("failed to get led-en gpio [%d]\n", ret);
> > + return ret;
> > + }
> > + } else {
> > + dp_panel->led_en_gpio = -ENODEV;
> > + }
> > +
> > + drm_panel_init(&dp_panel->base);
> > + dp_panel->base.dev = dev;
> > + dp_panel->base.funcs = &panel_exynos_dp_funcs;
> > +
> > + ret = drm_panel_add(&dp_panel->base);
> > + if (ret < 0)
> > + return ret;
> > +
> > + dev_set_drvdata(dev, dp_panel);
> > +
> > + return 0;
> > +}
> > +
> > +static int panel_exynos_dp_remove(struct platform_device *pdev)
> > +{
> > + struct panel_exynos_dp *dp_panel = dev_get_drvdata(&pdev->dev);
> > +
> > + drm_panel_detach(&dp_panel->base);
> > + drm_panel_remove(&dp_panel->base);
> > +
> > + panel_exynos_dp_disable(&dp_panel->base);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id exynos_dp_panel_dt_match[] = {
> > + { .compatible = "samsung,exynos-dp-panel" },
> > + {},
> > +};
> > +
> > +struct platform_driver exynos_dp_panel_driver = {
> > + .driver = {
> > + .name = "exynos-dp-panel",
> > + .owner = THIS_MODULE,
> > + .of_match_table = exynos_dp_panel_dt_match,
> > + },
> > + .probe = panel_exynos_dp_probe,
> > + .remove = panel_exynos_dp_remove,
> > +};
> > --
> > 1.8.1.2
>
>
Thanks and regards,
Ajay Kumar
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.freedesktop.org/archives/dri-devel/attachments/20140419/1f4ab29d/attachment-0001.html>
More information about the dri-devel
mailing list