[RFC v2 PATCH 02/14] drm/exynos: dsi: delay setting clocks after reset

[YoungJun Cho]

Hi Andrzej,

Thank you for the comments.

On 04/23/2014 04:37 PM, Andrzej Hajda wrote:
> On 04/23/2014 05:45 AM, YoungJun Cho wrote:
>> Hi again Andrzej,
>>
>> On 04/23/2014 10:01 AM, YoungJun Cho wrote:
>>> Hi Andrzej
>>>
>>> Thank you for comments.
>>>
>>> On 04/22/2014 09:15 PM, Andrzej Hajda wrote:
>>>> Hi YoungJun,
>>>>
>>>> On 04/21/2014 02:28 PM, YoungJun Cho wrote:
>>>>> Some phy control registers are not kept after software reset.
>>>>> So this patch makes the clocks containing phy control to be set
>>>>> after software reset.
>>>>>
>>>>> Signed-off-by: YoungJun Cho <yj44.cho at samsung.com>
>>>>> Acked-by: Inki Dae <inki.dae at samsung.com>
>>>>> Acked-by: Kyungmin Park <kyungmin.park at samsung.com>
>>>>> ---
>>>>>    drivers/gpu/drm/exynos/exynos_drm_dsi.c |    2 +-
>>>>>    1 file changed, 1 insertion(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
>>>>> b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
>>>>> index 956e5f3..2cf1f0b 100644
>>>>> --- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
>>>>> +++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
>>>>> @@ -946,10 +946,10 @@ static irqreturn_t exynos_dsi_irq(int irq, void
>>>>> *dev_id)
>>>>>
>>>>>    static int exynos_dsi_init(struct exynos_dsi *dsi)
>>>>>    {
>>>>> -    exynos_dsi_enable_clock(dsi);
>>>>>        exynos_dsi_reset(dsi);
>>>>>        enable_irq(dsi->irq);
>>>>>        exynos_dsi_wait_for_reset(dsi);
>>>>> +    exynos_dsi_enable_clock(dsi);
>>>>>        exynos_dsi_init_link(dsi);
>>>>>
>>>>>        return 0;
>>>>
>>>> I have commented it in the previous version of the patchset. I repeat it
>>>> again.
>>>> This is a regression, on exynos4210-trats I have 'timeout waiting for
>>>> reset' message after dpms off, on.
>>>
>>> I'm really sorry for that. I misunderstood last time.
>>>
>>> I think the original codes were correct, because the reset timeout would
>>> be occurred without clock activation.
>>
>> This is not true.
>>
>>>
>>> I'll check and fix again.
>>> (By the way, why am I ok?)
>>
>> I have not verified with exynos4210-trats board yet(I have to get it),
>> but reset timeout is occured in exynos_dsi_wait_for_reset()
>> with &dsi->completed and that is completed by exynos_dsi_irq().
>>
>> And the regulators and clocks are enabled by exynos_dsi_poweron(),
>> NOT by exynos_dsi_enable_clock().
>>
>> So I think the reset timeout is not related with this patch.
>
>
> As far as I remember there were at least two issues with init sequence:
> - spurious irq storm after power on and before reset,
> - irq reset timeouts after reset and without enabled clock.
>
> The current sequence is a result of tests on live hw (documentation were
> not helpful in this case). I think it could be improved little bit more
> by moving exynos_dsi_enable_clock just after enable_irq this will
> eliminate possible timeout when RST_RELEASE irq is signaled but irq is
> still disabled. The sequence should look like below:
>
> 	exynos_dsi_reset(dsi);
> 	enable_irq(dsi->irq);
> 	exynos_dsi_enable_clock(dsi);
> 	exynos_dsi_wait_for_reset(dsi);
> 	exynos_dsi_init_link(dsi);
>
> And PHY related configuration could be put somewhere after
> exynos_dsi_wait_for_reset.
>
> I have tested this sequence on trats, it seems to be OK.

It also works well in Exynos5420 target.

I think it would be better to remove this patch and implement new PHY
control functions with this modification.

Thank you.
Best regards YJ

>
> Regards
> Andrzej
>
>
>>
>> Anyway I need more investigation.
>>
>> Thank you.
>> Best regards YJ
>>
>>>
>>>>
>>>> I will comment your previous answer here to make the discussion easier:
>>>>> As I mentioned in description, it came from phy control registers.
>>>>> Fortunately Exynos4 SoCs are safe, but the DSIM_PHYCTRL_REG,
>>>>> DSIM_PHYTIMING_REG, DSIM_PHYTIMING1_REG and DSIM_PHYTIMING2_REG are
>>>>> affected which are used in exynos_dsi_set_pll() for Exynos5 SoCs.
>>>>>
>>>>> So this patch is required for Exynos5 SoCs.
>>>>
>>>> In the moment this patch is applied exynos_dsi_set_pll do not touch phy
>>>> registers you have mentioned.
>>>> Your change would be more clear if it will be merged together with the
>>>> patch adding PHYCTRL settings.
>>>>
>>>> Anyway, solution is simple - please set PHY registers after reset and
>>>> configure clocks before reset to avoid
>>>> reset timeouts, is there any reason to not do it this way?
>>>
>>> The only reason is that the PHY control is related with PLL control and
>>> that was in exynos_dsi_enable_clock() call path.
>>> So I just wanted to keep current sequence.
>>>
>>> If there is no way to use previous one, I'll consider your approach.
>>>
>>> Thank you.
>>> Best regards YJ
>>>
>>>>
>>>> Regards
>>>> Andrzej
>>>>
>>>
>>> _______________________________________________
>>> dri-devel mailing list
>>> dri-devel at lists.freedesktop.org
>>> http://lists.freedesktop.org/mailman/listinfo/dri-devel
>>>
>>
>
>