Dual-channel DSI
Thierry Reding
thierry.reding at gmail.com
Thu Aug 7 00:25:31 PDT 2014
On Thu, Aug 07, 2014 at 08:53:47AM +0200, Andrzej Hajda wrote:
> Hi Thierry,
>
> Nice case.
>
> On 08/05/2014 05:39 PM, Thierry Reding wrote:
> > Hi everyone,
> >
> > I've been working on adding support for a panel that uses what's
> > commonly known as dual-channel DSI. Sometimes this is referred to as
> > ganged-mode as well.
> >
> > What is it, you ask? It's essentially a hack to work around the band-
> > width restrictions of DSI, albeit one that's been commonly implemented
> > by several SoC vendors.
> >
> > This typically works by equipping a peripheral with two DSI interfaces,
> > each of which driving one half of the screen (symmetric left-right mode)
> > or every other line (symmetric odd-even mode). Apparently there can be
> > asymmetric modes in addition to those two, but they seem to be the
> > common ones. Often both of the DSI interfaces need to be configured
> > using DCS commands and vendor specific registers.
> >
> > A single display controller is typically used video data transmission.
> > This is necessary to provide synchronization and avoid tearing and all
> > kinds of other ugliness. For this to work both DSI controllers need to
> > be made aware of which chunk of the video data stream is addressing
> > them.
> >
> > From a software perspective, this poses two problems:
> >
> > 1) A dual-channel device is composed of two DSI peripheral devices which
> > cannot be programmed independently of each other. A typical example
> > is that the frame memory extents need to be configured differently
> > for each of the devices (using the DCS set_column_address and
> > set_page_address commands). Therefore each device must know of the
> > other, or there must be a driver that binds against a dummy device
> > that pulls in the two real devices.
>
> I am not sure if I understand correctly, but I see it rather as one
> device with two dsi-slave interfaces. Probably panel driver can
> create dsi dummy device to program some registers
> via second dsi interface but the panel will be attached to one control bus.
> It seems to be very similar to mfd/i2c devices with two or more i2c
> addresses.
They are in fact attached to two different control busses. The DSI
controllers that talk to each are separate. On Tegra they are the same
type of IP block, but still two separate instances (with their own
clock, reset, etc. inputs).
So the panel driver can't create a dummy device to talk to the second
DSI interface because the second DSI interface uses a different DSI
host.
> > 2) On the DSI host side, each of the controller instances needs to know
> > the intimate details of the other controller (or alternatively, one
> > controller needs to be a "master" and the other a "slave").
>
> The question is if they need to communicate each other, or they have
> to have similar configurations applied?
On Tegra at least the configuration needs to be almost the same. There
are two registers that may need to be programmed differently. But they
don't have to communicate with each other. Essentially the two registers
that require different programming define which parts of the display
controller's data stream they need to capture and turn into DSI packets.
Theoretically it would be possible to make this work with two completely
different DSI controllers, but in practice I'd expect that to never
happen. So I'm not sure we need to consider the case where the register
layout is different between the two DSI host controllers.
> > I'm looking for feedback on how this is handled on other SoCs, hence
> > adding a few people that I know are working on DSI as well (or have in
> > the past). If you know of any other people that might have useful advice
> > on this topic, feel free to include them.
> >
> > Another goal of this discussion is to come up with a somewhat standard
> > way to represent this in device tree (oh no!) so that panels can be
> > easily reused on different SoCs.
> >
> > What I currently have for Tegra is something along these lines:
> >
> > dsi at 54300000 {
> > nvidia,ganged-mode = <&dsib>;
> >
> > panel at 0 {
> > compatible = "sharp,lq101r1sx01";
> > reg = <0>;
> >
> > secondary = <&secondary>;
> > };
> > };
> >
> > dsib: dsi at 54400000 {
> > nvidia,ganged-mode;
> >
> > secondary: panel at 0 {
> > reg = <0>;
> > };
> > };
> >
> > There are a couple of other properties in those nodes, such as
> > regulators and such, but I've omitted them so that the discussion can
> > focus on the important bits.
> >
> > In the above the panel driver will bind against dsi at 54300000/panel at 0 and
> > use the "secondary" property to obtain a reference to the DSI peripheral
> > device of the second DSI interface of the device.
> >
> > Similarly, the dsi at 54300000 primary DSI host will obtain a reference to
> > a "slave" DSI host via the "nvidia,ganged-mode" property. The secondary
> > DSI host dsi at 54400000 will know that it's not a fully functional DSI
> > output by the presence of the empty "nvidia,ganged-mode" property.
> >
> > Using the above I can get things to work, but it seems somewhat kludgy.
> > For example it assumes that both DSI hosts are the same type. I'm not
> > sure if it makes sense for dual-channel to use completely different DSI
> > hosts given that they need to be very tightly coupled (take input from
> > the same display controller, use the same PLL, ...). It's also kind of
> > redundant to have to specify the dual relationship twice (once for the
> > peripheral and once for the DSI hosts). There's also the issue that we
> > should really be specifying a compatible string for the secondary
> > instance of the DSI peripheral, but that would mean that it will bind
> > against the same driver and then both would be programmed independently
> > in the same way (without taking into account the differences between the
> > two interfaces).
> >
> > One alternative to the above could be something like this:
> >
> > dsi at 54300000 {
> > nvidia,ganged-mode = <&dsib>;
> > nvidia,panel = <&panel>
> >
> > primary: panel at 0 {
> > compatible = "sharp,lq101r1sx01-left";
> > reg = <0>;
> > };
> > };
> >
> > dsib: dsi at 54400000 {
> > nvidia,ganged-mode;
> >
> > secondary: panel at 0 {
> > compatible = "sharp,lq101r1sx01-right";
> > reg = <0>;
> > };
> > };
> >
> > panel {
> > compatible = "sharp,lq101r1sx01";
> > sharp,left = <&primary>;
> > sharp,right = <&secondary>;
> > };
> >
> > Which would give us a more natural way to represent this. On the other
> > hand we loose information about the device type (/panel is no longer a
> > DSI device) and associated meta-data (number of DSI lanes, ...).
> >
> > My primary concern is that this may not work for other SoCs since I've
> > only tested it against Tegra. But the goal would be that the same panel
> > connected to a different SoC would still be able to work with the same
> > device tree binding.
> >
> > It would be great if anybody could share if they know how this works on
> > other SoCs and if somebody's thought about how to implement it.
>
> What about strictly following general 'rules' in DT:
> 1. Control bus is modeled using subnodes.
> 2. Video bus is modeled using video interface bindings.
>
> Assuming this we will put panel node inside the first dsi node and we
> should make
> video link to other dsi node. Something like this:
>
> dsiA {
> ports {
> port at 0 {
> remote-endpoint = <&dc_port0>;
> };
> dsiA_port1: port at 1 {
> remote-endpoint = <&panel_port0>;
> };
> panel at 0 {
> compatible = "...";
> reg = <0>;
> ports {
> /* maybe common configuration for all ports */
> panel_port0: port at 0 {
> /* configuration specific for port at 0 */
> remote-endpoint = <&dsiA_port1>;
> };
> panel_port1: port at 1 {
> /* configuration specific for port at 1 */
> remote-endpoint = <&dsiB_port1>;
> };
> };
> };
> };
>
> dsiB {
> ports {
> port at 0 {
> remote-endpoint = <&dc_port1>;
> };
> dsiA_port1: port at 1 {
> remote-endpoint = <&panel_port1>;
> };
> };
Much of that information is redundant. For example the "DC" ports are
dynamically configurable at runtime. Also I think panel_port1 is not
necessary because the panel can work (admittedly somewhat crippled) with
only a single DSI interface. I've come up with another alternative that
works:
dsi at 54300000 {
panel: panel at 0 {
compatible = "sharp,lq101r1sx01";
reg = <0>;
};
};
dsi at 54400000 {
panel at 0 {
compatible = "sharp,lq101r1sx01";
reg = <0>;
master = <&panel>;
};
};
That's about as minimal as it gets. The meaning of the above is that
there are two panel devices, each connected to different DSI hosts, that
form a composite device. The first instance can be used standalone, in
which case it will only display one half of the screen, whereas the
second instance can attach to a master (the first instance). When
attached the master can "enslave" the secondary device and set up dual-
channel mode.
From a driver perspective in the above the two instances share the same
driver, but the slave device will only perform a subset of the
initialization, whereas the master device will be the controlling
instance. Furthermore the DSI host controller driver will check that the
secondary's DSI host is compatible (by comparing the mipi_dsi_host.dev->
driver fields) and configure it in ganged mode.
This does work out pretty nicely and I've added a bit of helper code to
the DSI core to make this easier. I'm considering making this more
explicit by introducing the concept of a mipi_dsi_master that wraps a
mipi_dsi_device and provides callbacks for setting up or tearing down
dual-channel mode when a slave is added or removed.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.freedesktop.org/archives/dri-devel/attachments/20140807/ed71067c/attachment.sig>
More information about the dri-devel
mailing list