[RFC PATCH v2 03/21] exynos/dsim: add DT bindings

[Inki Dae]

2014-02-12 20:31 GMT+09:00 Andrzej Hajda <a.hajda at samsung.com>:
> The patch adds DT bindings for Exynos DSI Master. DSIM follows rules
> for DSI bus host bindings [1].
> Properties describes its resources: memory, interrupt, clocks,
> phy, regulators and frequencies of clocks.
>
> [1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
>
> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
> ---
> v2
> - added burst and esc clock frequency properties
> - add samsung prefix to all frequency props
> ---
>  .../devicetree/bindings/video/exynos_dsim.txt      | 53 ++++++++++++++++++++++
>  1 file changed, 53 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/video/exynos_dsim.txt
>
> diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt
> new file mode 100644
> index 0000000..2a49704
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt
> @@ -0,0 +1,53 @@
> +Exynos MIPI DSI Master
> +
> +Required properties:
> +  - compatible: "samsung,exynos4210-mipi-dsi"
> +  - reg: physical base address and length of the registers set for the device
> +  - interrupts: should contain DSI interrupt
> +  - clocks: list of clock specifiers, must contain an entry for each required
> +    entry in clock-names
> +  - clock-names: should include "bus_clk"and "pll_clk" entries
> +  - phys: list of phy specifiers, must contain an entry for each required
> +    entry in phy-names
> +  - phy-names: should include "dsim" entry
> +  - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V)
> +  - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
> +  - samsung,pll-clock-frequency: specifies frequency of the "pll_clk" clock
> +  - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
> +    mode
> +  - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
> +  - #address-cells, #size-cells: should be set respectively to <1> and <0>
> +    according to DSI host bindings (see MIPI DSI bindings [1])
> +
> +Optional properties:
> +  - samsung,power-domain: a phandle to DSIM power domain node
> +
> +Child nodes:
> +  Should contain DSI peripheral nodes (see DSI bindings [1])
> +
> +[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
> +
> +Example:
> +
> +       dsi at 11C80000 {
> +               compatible = "samsung,exynos4210-mipi-dsi";
> +               reg = <0x11C80000 0x10000>;
> +               interrupts = <0 79 0>;
> +               clocks = <&clock 286>, <&clock 143>;
> +               clock-names = "bus_clk", "pll_clk";
> +               phys = <&mipi_phy 1>;
> +               phy-names = "dsim";
> +               vddcore-supply = <&vusb_reg>;
> +               vddio-supply = <&vmipi_reg>;
> +               samsung,power-domain = <&pd_lcd0>;
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               samsung,pll-clock-frequency = <24000000>;
> +               samsung,burst-clock-frequency = <500000000>;
> +               samsung,esc-clock-frequency = <20000000>;

Isn't a property indicating cpu or video mode needed for the future
even though now DSI driver doesn't support CPU interface yet? Which
mode is used would depend on machine.

> +
> +               panel at 0 {
> +                       reg = <0>;
> +                       ...
> +               };
> +       };
> --
> 1.8.3.2
>
> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/dri-devel