[PATCH v4 4/8] drm/exynos: dsi: rename pll_clk to sclk_clk

[Inki Dae]

On 2015년 04월 07일 20:57, Hyungwon Hwang wrote:
> This patch renames pll_clk to sclk_clk. The clock referenced by pll_clk
> is actually not the pll input clock for dsi. The pll input clock comes
> from the board's oscillator directly.
> 
> Signed-off-by: Hyungwon Hwang <human.hwang at samsung.com>
> ---
> Changes for v3:
> - Newly added
> 
> Changes for v4:
> - None
>  .../devicetree/bindings/video/exynos_dsim.txt      |  6 ++---
>  drivers/gpu/drm/exynos/exynos_drm_dsi.c            | 31 ++++++++--------------
>  2 files changed, 14 insertions(+), 23 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt
> index 802aa7e..39940ca 100644
> --- a/Documentation/devicetree/bindings/video/exynos_dsim.txt
> +++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt
> @@ -10,13 +10,13 @@ Required properties:
>    - interrupts: should contain DSI interrupt
>    - clocks: list of clock specifiers, must contain an entry for each required
>      entry in clock-names
> -  - clock-names: should include "bus_clk"and "pll_clk" entries
> +  - clock-names: should include "bus_clk"and "sclk_mipi" entries
>    - phys: list of phy specifiers, must contain an entry for each required
>      entry in phy-names
>    - phy-names: should include "dsim" entry
>    - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V)
>    - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
> -  - samsung,pll-clock-frequency: specifies frequency of the "pll_clk" clock
> +  - samsung,pll-clock-frequency: specifies frequency of the oscillator clock
>    - #address-cells, #size-cells: should be set respectively to <1> and <0>
>      according to DSI host bindings (see MIPI DSI bindings [1])
> 
> @@ -48,7 +48,7 @@ Example:
>  		reg = <0x11C80000 0x10000>;
>  		interrupts = <0 79 0>;
>  		clocks = <&clock 286>, <&clock 143>;
> -		clock-names = "bus_clk", "pll_clk";
> +		clock-names = "bus_clk", "sclk_mipi";
>  		phys = <&mipi_phy 1>;
>  		phy-names = "dsim";
>  		vddcore-supply = <&vusb_reg>;
> diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
> index 05fe93d..4af18b2f 100644
> --- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
> +++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
> @@ -277,7 +277,7 @@ struct exynos_dsi {
> 
>  	void __iomem *reg_base;
>  	struct phy *phy;
> -	struct clk *pll_clk;
> +	struct clk *sclk_clk;
>  	struct clk *bus_clk;
>  	struct regulator_bulk_data supplies[2];
>  	int irq;
> @@ -431,16 +431,7 @@ static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi,
>  	u16 m;
>  	u32 reg;
> 
> -	clk_set_rate(dsi->pll_clk, dsi->pll_clk_rate);
> -
> -	fin = clk_get_rate(dsi->pll_clk);
> -	if (!fin) {
> -		dev_err(dsi->dev, "failed to get PLL clock frequency\n");
> -		return 0;
> -	}
> -
> -	dev_dbg(dsi->dev, "PLL input frequency: %lu\n", fin);
> -
> +	fin = dsi->pll_clk_rate;
>  	fout = exynos_dsi_pll_find_pms(dsi, fin, freq, &p, &m, &s);
>  	if (!fout) {
>  		dev_err(dsi->dev,
> @@ -1308,10 +1299,10 @@ static int exynos_dsi_poweron(struct exynos_dsi *dsi)
>  		goto err_bus_clk;
>  	}
> 
> -	ret = clk_prepare_enable(dsi->pll_clk);
> +	ret = clk_prepare_enable(dsi->sclk_clk);
>  	if (ret < 0) {
>  		dev_err(dsi->dev, "cannot enable pll clock %d\n", ret);
> -		goto err_pll_clk;
> +		goto err_sclk_clk;
>  	}
> 
>  	ret = phy_power_on(dsi->phy);
> @@ -1323,8 +1314,8 @@ static int exynos_dsi_poweron(struct exynos_dsi *dsi)
>  	return 0;
> 
>  err_phy:
> -	clk_disable_unprepare(dsi->pll_clk);
> -err_pll_clk:
> +	clk_disable_unprepare(dsi->sclk_clk);
> +err_sclk_clk:
>  	clk_disable_unprepare(dsi->bus_clk);
>  err_bus_clk:
>  	regulator_bulk_disable(ARRAY_SIZE(dsi->supplies), dsi->supplies);
> @@ -1350,7 +1341,7 @@ static void exynos_dsi_poweroff(struct exynos_dsi *dsi)
> 
>  	phy_power_off(dsi->phy);
> 
> -	clk_disable_unprepare(dsi->pll_clk);
> +	clk_disable_unprepare(dsi->sclk_clk);
>  	clk_disable_unprepare(dsi->bus_clk);
> 
>  	ret = regulator_bulk_disable(ARRAY_SIZE(dsi->supplies), dsi->supplies);
> @@ -1720,10 +1711,10 @@ static int exynos_dsi_probe(struct platform_device *pdev)
>  		return -EPROBE_DEFER;
>  	}
> 
> -	dsi->pll_clk = devm_clk_get(dev, "pll_clk");
> -	if (IS_ERR(dsi->pll_clk)) {
> -		dev_info(dev, "failed to get dsi pll input clock\n");
> -		ret = PTR_ERR(dsi->pll_clk);
> +	dsi->sclk_clk = devm_clk_get(dev, "sclk_mipi");

You changed only clock name of driver so with this patch, dsi driver
wouldn't work because device tree still has 'pll_clk' as clock name. And
you should also consider backward compatibility because existing dtb has
'pll_clk' which cannot be changed. The change of clock name, pll_clk
->sclk_mipi, seems reasonable to me.

Thanks,
Inki Dae

> +	if (IS_ERR(dsi->sclk_clk)) {
> +		dev_info(dev, "failed to get dsi sclk clock\n");
> +		ret = PTR_ERR(dsi->sclk_clk);
>  		goto err_del_component;
>  	}
> 
> --
> 1.9.1
> 
>