[PATCH v2 1/7] drm/vc4: Add devicetree bindings for VC4.

[Eric Anholt]

VC4 is the GPU (display and 3D) subsystem present on the 2835 and some
other Broadcom SoCs.

This binding follows the model of msm, imx, sti, and others, where
there is a subsystem node for the whole GPU, with nodes for the
individual HW components within it.

Signed-off-by: Eric Anholt <eric at anholt.net>
---

v2: Extend the commit message, fix several nits from Stephen Warren.

 .../devicetree/bindings/gpu/brcm,bcm-vc4.txt       | 79 ++++++++++++++++++++++
 1 file changed, 79 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpu/brcm,bcm-vc4.txt

diff --git a/Documentation/devicetree/bindings/gpu/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/gpu/brcm,bcm-vc4.txt
new file mode 100644
index 0000000..1b9fedc
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpu/brcm,bcm-vc4.txt
@@ -0,0 +1,79 @@
+Broadcom VC4 GPU
+
+The VC4 device present on the Raspberry Pi includes a display system
+with HDMI output and the HVS scaler for compositing display planes.
+
+Required properties for VC4:
+- compatible:	Should be "brcm,vc4"
+- crtcs:	List of phandles of pixelvalve scanout engines
+- hvss:		List of phandles of HVS video scalers
+- encoders:	List of phandles of output encoders (HDMI, SDTV)
+
+Required properties for Pixel Valve:
+- compatible:	Should be "brcm,vc4-pixelvalve"
+- reg:		Physical base address and length of the PV's registers
+- interrupts:	The interrupt number
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+
+Required properties for HVS:
+- compatible:	Should be "brcm,vc4-hvs"
+- reg:		Physical base address and length of the HVS's registers
+- interrupts:	The interrupt number
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+
+Required properties for HDMI
+- compatible:	Should be "brcm,vc4-hdmi"
+- reg:		Physical base address and length of the two register ranges
+		  ("HDMI" and "HD", in that order)
+- interrupts:	The interrupt numbers
+		  See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
+- ddc:		phandle of the I2C controller used for DDC EDID probing
+- crtc:		phandle to the pixelvalve CRTC the HDMI encoder is attached to
+
+Optional properties for HDMI:
+- hpd-gpio:	The GPIO pin for HDMI hotplug detect (if it doesn't appear
+		  as an interrupt/status bit in the HDMI controller
+		  itself).  See bindings/pinctrl/brcm,bcm2835-gpio.txt
+
+Example:
+pv0: brcm,vc4-pixelvalve at 7e206000 {
+	compatible = "brcm,vc4-pixelvalve";
+	reg = <0x7e206000 0x100>;
+	interrupts = <2 13>; /* pwa2 */
+};
+
+pv1: brcm,vc4-pixelvalve at 7e207000 {
+	compatible = "brcm,vc4-pixelvalve";
+	reg = <0x7e207000 0x100>;
+	interrupts = <2 14>; /* pwa1 */
+};
+
+pv2: brcm,vc4-pixelvalve at 7e807000 {
+	compatible = "brcm,vc4-pixelvalve";
+	reg = <0x7e807000 0x100>;
+	interrupts = <2 10>; /* pixelvalve */
+};
+
+hvs: brcm,hvs at 7e400000 {
+	compatible = "brcm,vc4-hvs";
+	reg = <0x7e400000 0x6000>;
+	interrupts = <2 1>;
+};
+
+hdmi: brcm,vc4-hdmi at 7e902000 {
+	compatible = "brcm,vc4-hdmi";
+	reg = <0x7e902000 0x600>,
+	      <0x7e808000 0x100>;
+	interrupts = <2 8>, <2 9>;
+	ddc = <&i2c2>;
+	hpd-gpio = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	crtc = <&pv2>;
+};
+
+vc4: vc4 at 0x7e4c0000 {
+	compatible = "brcm,vc4";
+
+	crtcs = <&pv0>, <&pv1>, <&pv2>;
+	encoders = <&hdmi>;
+	hvss = <&hvs>;
+};
-- 
2.1.4