[PATCH 04/12] gpu: imx: fix support for interlaced modes

[Philipp Zabel]

Am Donnerstag, den 27.08.2015, 09:54 +0100 schrieb Russell King - ARM
Linux:
> On Thu, Aug 27, 2015 at 10:39:12AM +0200, Philipp Zabel wrote:
> > Hi Russell,
> > 
> > Am Samstag, den 08.08.2015, 17:03 +0100 schrieb Russell King:
> > > The support for interlaced video modes seems to be broken; we don't use
> > > anything other than the vtotal/htotal from the timing information to
> > > define the various sync counters.
> > 
> > I finally made time to test this series:
> > 
> > Tested-by: Philipp Zabel <p.zabel at pengutronix.de>
> > on i.MX6 GK802 via HDMI connected to a TV (1080p60, 1080i60).
> > 
> > Unfortunately these timings are completely different from what Freescale
> > came up with for the TV Encoder on i.MX5, but the code we have currently
> > in mainline doesn't work for that either. I suppose I'll follow up with
> > a patch that adds yet another sync counter setup for the i.MX5/TVE case.
> > 
> > I'd like to take the two ipu-v3 patches, making a few small changes on
> > this one:
> 
> Please don't split the series up.  The reason it's a series is because
> there's interdependencies between the patches.

In that case, can I take the whole series? Or would you like to respin
and have my Acked-by: Philipp Zabel <p.zabel at pengutronix.de> with the
changes below:

> > > Freescale patches for interlaced video support contain an alternative
> > > sync counter setup, which we include here.  This setup produces the
> > > hsync and vsync via the normal counter 2 and 3, but moves the display
> > > enable signal from counter 5 to counter 6.  Therefore, we need to
> > > change the display controller setup as well.
> > > 
> > > The corresponding Freescale patches for this change are:
> > >   iMX6-HDMI-support-interlaced-display-mode.patch
> > >   IPU-fine-tuning-the-interlace-display-timing-for-CEA.patch
> > > 
> > > This produces a working interlace format output from the IPU.
> > 
> > ... on i.MX6 via HDMI.
> 
> It should also be correct for any other source which wants interlaced
> output.

... on i.MX6, then. Right now I don't know what is the effect of the
undocumented settings on the i.MX5's IPUv3M.

> > > Signed-off-by: Russell King <rmk+kernel at arm.linux.org.uk>
> > > ---
> > >  drivers/gpu/ipu-v3/ipu-dc.c | 18 ++++++++---
> > >  drivers/gpu/ipu-v3/ipu-di.c | 79 +++++++++++++++++++++------------------------
> > >  2 files changed, 51 insertions(+), 46 deletions(-)
> > > 
> > > diff --git a/drivers/gpu/ipu-v3/ipu-dc.c b/drivers/gpu/ipu-v3/ipu-dc.c
> > > index 9ef2e1f54ca4..aa560855c1dc 100644
> > > --- a/drivers/gpu/ipu-v3/ipu-dc.c
> > > +++ b/drivers/gpu/ipu-v3/ipu-dc.c
> > > @@ -183,12 +183,22 @@ int ipu_dc_init_sync(struct ipu_dc *dc, struct ipu_di *di, bool interlaced,
> > >  	}
> > >  
> > >  	if (interlaced) {
> > > -		dc_link_event(dc, DC_EVT_NL, 0, 3);
> > > -		dc_link_event(dc, DC_EVT_EOL, 0, 2);
> > > -		dc_link_event(dc, DC_EVT_NEW_DATA, 0, 1);
> > > +		int word, addr;
> > > +
> > > +		if (dc->di) {
> > > +			addr = 1;
> > > +			word = 1;
> > 
> > These two are really one and the same. The address written to the link
> > register for the given event has to point to the address of the
> > microcode instruction written to the template memory that should be
> > executed on this event.
> > 
> > I'd like to drop the word variable and use addr for both.
> 
> Ok.  As I said in the commit message, this code comes from Freescale's
> patches which I pointed to above.
[...]
> > > @@ -211,66 +215,59 @@ static void ipu_di_sync_config_interlaced(struct ipu_di *di,
> > >  		sig->mode.hback_porch + sig->mode.hfront_porch;
> > >  	u32 v_total = sig->mode.vactive + sig->mode.vsync_len +
> > >  		sig->mode.vback_porch + sig->mode.vfront_porch;
> > > -	u32 reg;
> > >  	struct di_sync_config cfg[] = {
> > >  		{
> > > -			.run_count = h_total / 2 - 1,
> > > -			.run_src = DI_SYNC_CLK,
> > > +			/* 1: internal VSYNC for each frame */
> > > +			.run_count = v_total * 2 - 1,
> > > +			.run_src = 3,			/* == counter 7 */
> > 
> > Do you know why this works? The Reference Manual v2 lists that value as
> > "NA" in the DI counter #1 Run Resolution field.
> 
> Yes, I noticed that Freescale were using values for the source fields
> which were marked as NA in the manual.  As it works, I can only assume
> that the engineer who came up with this setup has more knowledge than
> is public.

I'd like small a comment here that yes, we know this is marked as
NA/Reserved in the manuals.

[...]
> I went through the counter setup to understand how it works, and it
> seems correct provided you accept that the various source values do
> work as the code claims, which includes creating the vsync at the
> appropriate half-scanline position without needing this hack.
> 
> It's not easy to work back from the counter setup to get a mental
> picture of what's going on, but it is possible to do so.

Yes, being able to actually reference counters with higher numbers makes
things a lot easier to follow.

regards
Philipp