[PATCH v3 06/14] Documentation: drm/bridge: add document for analogix_dp
Yakir Yang
ykk at rock-chips.com
Sun Aug 23 19:19:55 PDT 2015
Hi Rob,
在 08/23/2015 06:23 PM, Rob Herring 写道:
> On Wed, Aug 19, 2015 at 9:50 AM, Yakir Yang <ykk at rock-chips.com> wrote:
>> Analogix dp driver is split from exynos dp driver, so we just
>> make an copy of exynos_dp.txt, and then simplify exynos_dp.txt
>>
>> Beside update some exynos dtsi file with the latest change
>> according to the devicetree binding documents.
> You can't just change the exynos bindings and break compatibility. Is
> there some agreement with exynos folks to do this?
>
Yeah, this change only start to introduce in version 3 series, so there is
no agreement or discuss before.
>
>> Signed-off-by: Yakir Yang <ykk at rock-chips.com>
>> ---
>> Changes in v3:
>> - Take Heiko suggest, add devicetree binding documents.
>> - Take Thierry Reding suggest, remove sync pol & colorimetry properies
>> from the new analogix dp driver devicetree binding.
>> - Update the exist exynos dtsi file with the latest DP DT properies.
>>
>> Changes in v2: None
>>
>> .../devicetree/bindings/drm/bridge/analogix_dp.txt | 70 ++++++++++++++++++++++
>> .../devicetree/bindings/video/exynos_dp.txt | 50 ++++++----------
>> arch/arm/boot/dts/exynos5250-arndale.dts | 10 ++--
>> arch/arm/boot/dts/exynos5250-smdk5250.dts | 10 ++--
>> arch/arm/boot/dts/exynos5250-snow.dts | 12 ++--
>> arch/arm/boot/dts/exynos5250-spring.dts | 12 ++--
>> arch/arm/boot/dts/exynos5420-peach-pit.dts | 12 ++--
>> arch/arm/boot/dts/exynos5420-smdk5420.dts | 10 ++--
>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 12 ++--
>> 9 files changed, 119 insertions(+), 79 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
>>
>> diff --git a/Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
>> new file mode 100644
>> index 0000000..6127018
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
>> @@ -0,0 +1,70 @@
>> +Analogix Display Port bridge bindings
>> +
>> +Required properties for dp-controller:
>> + -compatible:
>> + platform specific such as:
>> + * "samsung,exynos5-dp"
>> + * "rockchip,rk3288-dp"
>> + -reg:
>> + physical base address of the controller and length
>> + of memory mapped region.
>> + -interrupts:
>> + interrupt combiner values.
>> + -clocks:
>> + from common clock binding: handle to dp clock.
>> + -clock-names:
>> + from common clock binding: Shall be "dp".
>> + -interrupt-parent:
>> + phandle to Interrupt combiner node.
>> + -phys:
>> + from general PHY binding: the phandle for the PHY device.
>> + -phy-names:
>> + from general PHY binding: Should be "dp".
>> + -analogix,color-space:
>> + input video data format.
>> + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
>> + -analogix,color-depth:
>> + number of bits per colour component.
>> + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
> This seems pretty generic. Just use 6, 8, 10, or 12 for values. And
> drop the vendor prefix.
Okay, thanks
>> + -analogix,link-rate:
>> + max link rate supported by the eDP controller.
>> + LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A,
>> + LINK_RATE_5_40GBPS = 0x14
> Same here. I'd rather see something like "link-rate-mbps" and use the
> actual rate.
Like "link-rate-mbps = 162000", so I need of_property_read_u32() for
this prop.
Okay, done.
>> + -analogix,lane-count:
>> + max number of lanes supported by the eDP contoller.
>> + LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
> And drop the vendor prefix here.
Done
>> + -port@[X]: SoC specific port nodes with endpoint definitions as defined
>> + in Documentation/devicetree/bindings/media/video-interfaces.txt,
>> + please refer to the SoC specific binding document:
>> + * Documentation/devicetree/bindings/video/exynos_dp.txt
>> + * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt
>> +
>> +Optional properties for dp-controller:
>> + -analogix,hpd-gpio:
>> + Hotplug detect GPIO.
>> + Indicates which GPIO should be used for hotplug
>> + detection
> We should align with "hpd-gpios" used by HDMI connector binding. Or do
> we need a DP connector binding that this should be defined in?
> Probably so.
>
> The DRM related bindings are such a cluster f*ck with everyone picking
> their own way to do things. Just grep hpd in bindings for starters.
> That is just the tip.
>
Hmm... I don't understand how the HDMI connector binding works, there are no
driver that name with "hdmi-connector" compatible, does it just an
sample case
for all HDMI dts node?
But I'm okay with your suggest here, change "analogix,hpd-gpio" to
"hpd-gpios" ;)
>> + -video interfaces: Device node can contain video interface port
>> + nodes according to [1].
> Isn't this the same as ports above? How are they optional? 0 ports
> would be pretty useless.
I though I make an mistaken here, "-video interfaces" is the same as
previous "ports".
And "ports" is an required property in rockchip case, cause we use it to
bind "dp" driver
to crtc "vop" driver. But I thinks "ports" in not an required property
in exynos case, they
only use when there are a dp/lvds application scenarios.
Here are example (./arch/arm/boot/dts/exynos5420-peach-pit.dts):
&dp {
[...]
ports {
port at 0 {
dp_out: endpoint {
remote-endpoint = <&bridge_in>;
};
};
};
};
ps8625: lvds-bridge at 48 {
[...]
ports {
port at 0 {
bridge_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
port at 1 {
bridge_in: endpoint {
remote-endpoint = <&dp_out>;
};
};
};
};
So I would rather to remove "ports" to analogix_dp-rockchip.txt with
"required" flag,
and keep "video-port" in analogox-dp.txt with "optional" flag.
>> +
>> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>> +-------------------------------------------------------------------------------
>> +
>> +Example:
>> +
>> + dp-controller {
>> + compatible = "samsung,exynos5-dp";
>> + reg = <0x145b0000 0x10000>;
>> + interrupts = <10 3>;
>> + interrupt-parent = <&combiner>;
>> + clocks = <&clock 342>;
>> + clock-names = "dp";
>> +
>> + phys = <&dp_phy>;
>> + phy-names = "dp";
>> +
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <4>;
>> + };
>> diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt
>> index 7a3a9cd..177506f 100644
>> --- a/Documentation/devicetree/bindings/video/exynos_dp.txt
>> +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt
>> @@ -31,28 +31,10 @@ Required properties for dp-controller:
>> from general PHY binding: the phandle for the PHY device.
>> -phy-names:
>> from general PHY binding: Should be "dp".
>> - -samsung,color-space:
>> - input video data format.
>> - COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
>> - -samsung,dynamic-range:
>> - dynamic range for input video data.
>> - VESA = 0, CEA = 1
>> - -samsung,ycbcr-coeff:
>> - YCbCr co-efficients for input video.
>> - COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
>> - -samsung,color-depth:
>> - number of bits per colour component.
>> - COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
>> - -samsung,link-rate:
>> - link rate supported by the panel.
>> - LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
>> - -samsung,lane-count:
>> - number of lanes supported by the panel.
>> - LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
>> - - display-timings: timings for the connected panel as described by
>> - Documentation/devicetree/bindings/video/display-timing.txt
>>
>> Optional properties for dp-controller:
>> + - display-timings: timings for the connected panel as described by
>> + Documentation/devicetree/bindings/video/display-timing.txt
>> -interlaced:
>> interlace scan mode.
>> Progressive if defined, Interlaced if not defined
>> @@ -62,14 +44,18 @@ Optional properties for dp-controller:
>> -hsync-active-high:
>> HSYNC polarity configuration.
>> High if defined, Low if not defined
>> - -samsung,hpd-gpio:
>> - Hotplug detect GPIO.
>> - Indicates which GPIO should be used for hotplug
>> - detection
>> - -video interfaces: Device node can contain video interface port
>> - nodes according to [1].
>>
>> -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>> +For the below properties, please refer to Analogix DP binding document:
>> + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
>> + -phys (required)
>> + -phy-names (required)
>> + -analogix,color-space (required)
>> + -analogix,color-depth (required)
>> + -analogix,link-rate (required)
>> + -analogix,lane-count (required)
>> + -analogix,hpd-gpio (optional)
>> + -video interfaces (optional)
>> +-------------------------------------------------------------------------------
>>
>> Example:
>>
>> @@ -88,12 +74,10 @@ SOC specific portion:
>>
>> Board Specific portion:
>> dp-controller {
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <4>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <4>;
>>
>> display-timings {
>> native-mode = <&lcd_timing>;
>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>> index 7e728a1..e48798d 100644
>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>> @@ -119,12 +119,10 @@
>>
>> &dp {
>> status = "okay";
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <4>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <4>;
>> };
>>
>> &fimd {
>> diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
>> index 4fe186d..b8c6b8b 100644
>> --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
>> +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
>> @@ -75,12 +75,10 @@
>> };
>>
>> &dp {
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <4>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <4>;
>>
>> pinctrl-names = "default";
>> pinctrl-0 = <&dp_hpd>;
>> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
>> index b7f4122..9ce2b89 100644
>> --- a/arch/arm/boot/dts/exynos5250-snow.dts
>> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
>> @@ -239,13 +239,11 @@
>> status = "okay";
>> pinctrl-names = "default";
>> pinctrl-0 = <&dp_hpd>;
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <2>;
>> - samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <2>;
>> + analogix,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
>>
>> ports {
>> port at 0 {
>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
>> index d03f9b8..9288ae6 100644
>> --- a/arch/arm/boot/dts/exynos5250-spring.dts
>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts
>> @@ -69,13 +69,11 @@
>> status = "okay";
>> pinctrl-names = "default";
>> pinctrl-0 = <&dp_hpd_gpio>;
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <1>;
>> - samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <1>;
>> + analogix,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
>> };
>>
>> &ehci {
>> diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> index 8f4d76c..695a380 100644
>> --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
>> @@ -147,13 +147,11 @@
>> status = "okay";
>> pinctrl-names = "default";
>> pinctrl-0 = <&dp_hpd_gpio>;
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x06>;
>> - samsung,lane-count = <2>;
>> - samsung,hpd-gpio = <&gpx2 6 0>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x06>;
>> + analogix,lane-count = <2>;
>> + analogix,hpd-gpio = <&gpx2 6 0>;
>>
>> ports {
>> port at 0 {
>> diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> index 98871f9..fd46714 100644
>> --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> @@ -91,12 +91,10 @@
>> &dp {
>> pinctrl-names = "default";
>> pinctrl-0 = <&dp_hpd>;
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <4>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <4>;
>> status = "okay";
>> };
>>
>> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> index 7d5b386..54b4c63 100644
>> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
>> @@ -141,13 +141,11 @@
>> status = "okay";
>> pinctrl-names = "default";
>> pinctrl-0 = <&dp_hpd_gpio>;
>> - samsung,color-space = <0>;
>> - samsung,dynamic-range = <0>;
>> - samsung,ycbcr-coeff = <0>;
>> - samsung,color-depth = <1>;
>> - samsung,link-rate = <0x0a>;
>> - samsung,lane-count = <2>;
>> - samsung,hpd-gpio = <&gpx2 6 0>;
>> + analogix,color-space = <0>;
>> + analogix,color-depth = <1>;
>> + analogix,link-rate = <0x0a>;
>> + analogix,lane-count = <2>;
>> + analogix,hpd-gpio = <&gpx2 6 0>;
>> panel = <&panel>;
>> };
>>
>> --
>> 1.9.1
>>
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
More information about the dri-devel
mailing list