[PATCH 3/3] dt-bindings: exynos-dp: update ports node binding for panel

[Inki Dae]

Hi Javier,

2015년 12월 03일 22:29에 Javier Martinez Canillas 이(가) 쓴 글:
> Hello Inki,
> 
> On 12/03/2015 06:30 AM, Inki Dae wrote:
>> This patch updates a ports node binding for panel.
>>
>> With this, dp node can have a ports node which describes
>> a remote endpoint node that can be connected to panel or bridge
>> node.
>>
>> Signed-off-by: Inki Dae <inki.dae at samsung.com>
>> ---
>>  .../bindings/display/exynos/exynos_dp.txt          | 28 ++++++++++++++++++----
>>  1 file changed, 24 insertions(+), 4 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> index 64693f2..15b52cb 100644
>> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> @@ -66,8 +66,15 @@ Optional properties for dp-controller:
>>  		Hotplug detect GPIO.
>>  			Indicates which GPIO should be used for hotplug
>>  			detection
>> -	-video interfaces: Device node can contain video interface port
>> -			    nodes according to [1].
>> +Video interfaces:
>> +  Device node can contain video interface port nodes according to [1].
>> +  The following are properties specific to those nodes:
>> +
>> +  endpoint node connected to bridge or panel node:
>> +   - remote-endpoint: specifies the endpoint in panel or bridge node.
>> +		      This node is required in all kinds of exynos dp
>> +		      to represent the connection between dp and bridge
>> +		      ,or dp and panel.
>>
> 
> This is nice but I think the DT binding should also document that it uses
> a phandle to define the connection with the panel (but explain that is
> deprecated). If only so people looking at a DTS and then going to the DT
> binding can understand why there is two ways to define the same.
>   
>>  [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>>  
>> @@ -111,9 +118,22 @@ Board Specific portion:
>>  		};
>>  
>>  		ports {
>> -			port at 0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
> 
> These two properties are only needed when there is more than 2 ports and
> a reg property is used to number the port nodes but I don't think that's
> the case for Exynos DP and certainly is not the case in this example so
> I think you should just remove them.

Right. I found out that the dp can have only one port outbound. Will remove them.

> 
>> +			port {
>>  				dp_out: endpoint {
>> -					remote-endpoint = <&bridge_in>;
>> +					remote-endpoint = <&dp_in>;
>> +				};
>> +			};
>> +		};
>> +
>> +		panel at 0 {
>> +			reg = <0>;
>> +			...
>> +			port {
>> +				dp_in: endpoint {
>> +					remote-endpoint = <&dp_out>;
>>  				};
>>  			};
>>  		};
>>
> 
> The rest looks good to me so with the two changes feel free to add:
> 
> Reviewed-by: Javier Martinez Canillas <javier at osg.samsung.com>

Thanks,
Inki Dae

> 
> Best regards,
>