[PATCH] drm/dp: Use large transactions for I2C over AUX

[Daniel Vetter]

On Fri, Jan 23, 2015 at 10:21:09PM +0100, Thierry Reding wrote:
> On Fri, Jan 23, 2015 at 09:46:29PM +0200, Ville Syrjälä wrote:
> > On Fri, Jan 23, 2015 at 06:40:38PM +0000, Simon Farnsworth wrote:
> > > DisplayPort to DVI-D Dual Link adapters designed by Bizlink have bugs in
> > > their I2C over AUX implementation. They work fine with Windows, but fail
> > > with Linux.
> > > 
> > > It turns out that they cannot keep an I2C transaction open unless the
> > > previous read was 16 bytes; shorter reads can only be followed by a zero
> > > byte transfer ending the I2C transaction.
> > > 
> > > Copy Windows's behaviour, and read 16 bytes at a time. Analysis of the
> > > failure state was provided by Datapath Ltd.
> > > 
> > > Signed-off-by: Simon Farnsworth <simon.farnsworth at onelan.co.uk>
> > > ---
> > > Thierry,
> > > 
> > > You put in the comment about "decreased performance", back in December 2013;
> > > would you mind testing that this still works with the devices you tested?
> > > 
> > > Unfortunately, Bizlink are the only game in town for DP->DVI-DL adapters -
> > > and their firmware is prone to giving up on I2C if we look at it
> > > wrongly. Even Apple's device is Bizlink designed.
> > > 
> > >  drivers/gpu/drm/drm_dp_helper.c | 13 +++++--------
> > >  1 file changed, 5 insertions(+), 8 deletions(-)
> > > 
> > > diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
> > > index 79968e3..b4a9d4a 100644
> > > --- a/drivers/gpu/drm/drm_dp_helper.c
> > > +++ b/drivers/gpu/drm/drm_dp_helper.c
> > > @@ -507,16 +507,13 @@ static int drm_dp_i2c_xfer(struct i2c_adapter *adapter, struct i2c_msg *msgs,
> > >  		err = drm_dp_i2c_do_msg(aux, &msg);
> > >  		if (err < 0)
> > >  			break;
> > > -		/*
> > > -		 * Many hardware implementations support FIFOs larger than a
> > > -		 * single byte, but it has been empirically determined that
> > > -		 * transferring data in larger chunks can actually lead to
> > > -		 * decreased performance. Therefore each message is simply
> > > -		 * transferred byte-by-byte.
> > > +		/* Bizlink designed DP->DVI-D Dual Link adapters require the
> > > +                 * I2C over AUX packets to be as large as possible. If not,
> > > +                 * the I2C transactions never succeed.
> > >  		 */
> > > -		for (j = 0; j < msgs[i].len; j++) {
> > > +		for (j = 0; j < msgs[i].len; j+=16) {
> > >  			msg.buffer = msgs[i].buf + j;
> > > -			msg.size = 1;
> > > +			msg.size = min(16, msgs[i].len - 16);
> > 
> > I don't think it's quite this simple. The sink is allowed to ACK
> > partial data for multi-byte messages. The code doesn't handle that.
> 
> Also not all hardware may support transferring 16 bytes at a time. How
> does that work with these adapters? Does it mean they can't work on DP
> hardware that can't do 16 byte block transfers?

If we handle short reads then hw which really can only do 1 byte at a time
could just always do that. But yeah that means you can't use these fancy
dp sinks with them I guess.
-Daniel
-- 
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch