[PATCH V9 13/14] ARM: dts: snow: represent the connection between bridge and panel using videoport and endpoints

[Ajay kumar]

Hi Kukjin,

On Fri, Jan 23, 2015 at 12:31 PM, Kukjin Kim <kgene at kernel.org> wrote:
> Ajay Kumar wrote:
>>
>> Define videoports and use endpoints to describe the connection between
>> the encoder, bridge and the panel, instead of using phandles.
>>
>> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
>> Acked-by: Inki Dae <inki.dae at samsung.com>
>> Tested-by: Rahul Sharma <rahul.sharma at samsung.com>
>> Tested-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
>> Tested-by: Gustavo Padovan <gustavo.padovan at collabora.co.uk>
>> Tested-by: Sjoerd Simons <sjoerd.simons at collabora.co.uk>
>> ---
>>  arch/arm/boot/dts/exynos5250-snow.dts |   30 ++++++++++++++++++++++++++++--
>>  1 file changed, 28 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
>> index b9aeec4..1bd5d3a 100644
>> --- a/arch/arm/boot/dts/exynos5250-snow.dts
>> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
>> @@ -183,7 +183,20 @@
>>                       powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
>>                       reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
>>                       edid-emulation = <5>;
>> -                     panel = <&panel>;
>> +
>> +                     ports {
>> +                             port at 0 {
>> +                                     bridge_out: endpoint {
>> +                                             remote-endpoint = <&panel_in>;
>> +                                     };
>> +                             };
>> +
>> +                             port at 1 {
>> +                                     bridge_in: endpoint {
>> +                                             remote-endpoint = <&dp_out>;
>> +                                     };
>> +                             };
>> +                     };
>>               };
>>       };
>>
>> @@ -228,6 +241,12 @@
>>               compatible = "auo,b116xw03";
>>               power-supply = <&fet6>;
>>               backlight = <&backlight>;
>> +
>> +             port {
>> +                     panel_in: endpoint {
>> +                             remote-endpoint = <&bridge_out>;
>> +                     };
>> +             };
>>       };
>>  };
>>
>> @@ -242,7 +261,14 @@
>>       samsung,link-rate = <0x0a>;
>>       samsung,lane-count = <2>;
>>       samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
>> -     bridge = <&ptn3460>;
>> +
>> +     ports {
>> +             port at 0 {
>> +                     dp_out: endpoint {
>> +                             remote-endpoint = <&bridge_in>;
>> +                     };
>> +             };
>> +     };
>>  };
>>
>>  &ehci {
>> --
>> 1.7.9.5
>
> I'm fine on the DT changes in this series, shall I take 13/14 and 14/14 in
> Samsung tree?
Yes, please take these patches.

Thanks and regards,
Ajay Kumar