[PATCH 09/10] dt-bindings: video: exynos5433-decon: add bindings for DECON-TV

[Krzysztof Kozlowski]

W dniu 20.10.2015 o 18:22, Andrzej Hajda pisze:
> DECON-TV(Display and Enhancement Controller for TV) is a variation
> of DECON IP. Its main purpose is to produce video stream for HDMI IP.
> 
> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
> ---
>  .../devicetree/bindings/video/exynos5433-decon.txt  | 21 ++++++++++++---------
>  1 file changed, 12 insertions(+), 9 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/video/exynos5433-decon.txt b/Documentation/devicetree/bindings/video/exynos5433-decon.txt
> index 3dff78b..2a88c8d 100644
> --- a/Documentation/devicetree/bindings/video/exynos5433-decon.txt
> +++ b/Documentation/devicetree/bindings/video/exynos5433-decon.txt
> @@ -5,24 +5,27 @@ Exynos series of SoCs which transfers the image data from a video memory
>  buffer to an external LCD interface.
>  
>  Required properties:
> -- compatible: value should be "samsung,exynos5433-decon";
> +- compatible: value should be one of:
> +	"samsung,exynos5433-decon", "samsung,exynos5433-decon-tv";

Until this point it looked good.

>  - reg: physical base address and length of the DECON registers set.
> -- interrupts: should contain a list of all DECON IP block interrupts in the
> -	      order: VSYNC, LCD_SYSTEM. The interrupt specifier format
> -	      depends on the interrupt controller used.
> -- interrupt-names: should contain the interrupt names: "vsync", "lcd_sys"
> -		   in the same order as they were listed in the interrupts
> -		   property.
> +- interrupts: should contain interrupt specifier of VSYNC and optionally
> +	      LCD_SYSTEM. The interrupt specifier format depends on
> +	      the interrupt controller used.
> +- interrupt-names: should contain the interrupt name "vsync" and optionally
> +		   "lcd_sys" in the same order as they were listed in
> +		   the interrupts property.

The driver already did not require both interrupts, right? Only one of them?

>  - clocks: must include clock specifiers corresponding to entries in the
>  	  clock-names property.
>  - clock-names: list of clock names sorted in the same order as the clocks
>  	       property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x",
>  	       "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk",
>  	       "sclk_decon_eclk"
> +
> +Optional properties:
>  - ports: contains a port which is connected to mic node. address-cells and
> -	 size-cells must 1 and 0, respectively.
> +	 size-cells must be 1 and 0, respectively.
>  - port: contains an endpoint node which is connected to the endpoint in the mic
> -	node. The reg value muset be 0.
> +	node. The reg value must be 0.
>  - i80-if-timings: specify whether the panel which is connected to decon uses
>  		  i80 lcd interface or mipi video interface. This node contains
>  		  no timing information as that of fimd does. Because there is
> 

This is cleanup, please split it.

Best regards,
Krzysztof