[RFC v3 5/7] dt-bindings: drm/mediatek: Add Mediatek HDMI dts binding

Philipp Zabel p.zabel at pengutronix.de
Wed Sep 30 08:30:04 PDT 2015


Add the device tree binding documentation for Mediatek HDMI,
HDMI PHY and HDMI DDC devices.

Signed-off-by: Philipp Zabel <p.zabel at pengutronix.de>
---
 .../bindings/drm/mediatek/mediatek,hdmi.txt        | 117 +++++++++++++++++++++
 1 file changed, 117 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt

diff --git a/Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt
new file mode 100644
index 0000000..96d09bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/mediatek/mediatek,hdmi.txt
@@ -0,0 +1,117 @@
+Mediatek HDMI Encoder
+=====================
+
+The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
+its parallel input.
+
+Required properties:
+- compatible: Should be "mediatek,<chip>-hdmi".
+- reg: Physical base address and length of the controller's registers
+- reg-names: must contain "grl", "cec", and "sys".
+- interrupts: The interrupt signal from the function block.
+- clocks: device clocks
+  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
+- clock-names: must contain "cec", "hdmi_sel", "hdmi_div1", "hdmi_div2",
+  "hdmi_div3", "hdmi_pixel", "hdmi_pll", "aud_bclk", and "aud_spdif".
+- ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing
+- phys: phandle link to the HDMI PHY node.
+  See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
+- phy-names: must contain "hdmi"
+- ports: A node containing input and output port nodes with endpoint
+  definitions as documented in Documentation/devicetree/bindings/graph.txt.
+- port at 0: The input port in the ports node should be connected to a DPI output
+  port.
+
+Optional properties:
+- port at 1: The output port in the ports node can be connected to the input port
+  of an attached bridge chip, such as a SlimPort transmitter.
+
+HDMI DDC
+========
+
+The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
+The Mediatek's I2C controller is used to interface with I2C devices.
+
+Required properties:
+- compatible: Should be "mediatek,<chip>-hdmi-ddc"
+- reg: Physical base address and length of the controller's registers
+- clocks: device clock
+- clock-names: Must contain "ddc-i2c".
+
+HDMI PHY
+========
+
+The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
+output and drives the HDMI pads.
+
+Required properties:
+- compatible: "mediatek,<chip>-hdmi-phy"
+- reg: Physical base address and length of the module's registers
+- #phy-cells: must be <0>.
+
+Optional properties:
+- ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
+- ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
+
+Example:
+
+hdmi_phy: hdmi-phy at 10209100 {
+	compatible = "mediatek,mt8173-hdmi-phy";
+	reg = <0 0x10209100 0 0x24>;
+	ibias = <0xa>;
+	ibias_up = <0x1c>;
+	#phy-cells = <0>;
+};
+
+hdmi_ddc0: i2c at 11012000 {
+	compatible = "mediatek,mt8173-hdmi-ddc";
+	reg = <0 0x11012000 0 0x1c>;
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&pericfg CLK_PERI_I2C5>;
+};
+
+hdmi0: hdmi at 14025000 {
+	compatible = "mediatek,mt8173-hdmi";
+	reg = <0 0x14025000 0 0x400>,	/* GRL */
+	      <0 0x10013000 0 0xbc>,	/* CEC */
+	      <0 0x14000900 0 0x8>;	/* SYS */
+	reg-names = "grl", "cec", "sys";
+	interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&infracfg CLK_INFRA_CEC>,
+		 <&topckgen CLK_TOP_HDMI_SEL>,
+		 <&topckgen CLK_TOP_HDMITX_DIG_CTS>,
+		 <&topckgen CLK_TOP_HDMITXPLL_D2>,
+		 <&topckgen CLK_TOP_HDMITXPLL_D3>,
+		 <&mmsys CLK_MM_HDMI_PIXEL>,
+		 <&mmsys CLK_MM_HDMI_PLLCK>,
+		 <&mmsys CLK_MM_HDMI_AUDIO>,
+		 <&mmsys CLK_MM_HDMI_SPDIF>;
+	clock-names = "cec",
+		      "hdmi_sel",
+		      "hdmi_div1",
+		      "hdmi_div2",
+		      "hdmi_div3",
+		      "hdmi_pixel",
+		      "hdmi_pll",
+		      "aud_bclk",
+		      "aud_spdif";
+	ddc-i2c-bus = <&hdmi_ddc0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_pin>;
+	phys = <&hdmi_phy>;
+	phy-names = "hdmi";
+	status = "disabled";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 0 {
+			reg = <0>;
+
+			hdmi0_in: endpoint {
+				remote-endpoint = <&dpi0_out>;
+			};
+		};
+	};
+};
-- 
2.5.3



More information about the dri-devel mailing list