[PATCH v3 1/2] drm: bridge: Add sii902x driver

[Boris Brezillon]

Hi Meng,

On Fri, 22 Apr 2016 09:58:34 +0000
Meng Yi <meng.yi at nxp.com> wrote:

> Hi Boris,
> 
> > -----Original Message-----
> > From: Boris Brezillon [mailto:boris.brezillon at free-electrons.com]
> > +
> 
> > +static int sii902x_bridge_attach(struct drm_bridge *bridge) {
> > +	const struct drm_connector_funcs *funcs = &sii902x_connector_funcs;
> > +	struct sii902x *sii902x = bridge_to_sii902x(bridge);
> > +	struct drm_device *drm = bridge->dev;
> > +	int ret;
> > +
> > +	drm_connector_helper_add(&sii902x->connector,
> > +				 &sii902x_connector_helper_funcs);
> > +
> > +	if (drm_core_check_feature(drm, DRIVER_ATOMIC))
> > +		funcs = &sii902x_atomic_connector_funcs;
> > +
> > +	ret = drm_connector_init(drm, &sii902x->connector, funcs,
> > +				 DRM_MODE_CONNECTOR_HDMIA);
> > +	if (ret)
> > +		return ret;
> > +
> 
> 
> I think drm_connector_register should be used here, or drmlib can't find this connector.

Hm, I think this should be left to the DRM master device
(some of them already call drm_connector_register_all() at the end of
their ->probe() function).

> 
> 
> > +	if (sii902x->i2c->irq > 0)
> > +		sii902x->connector.polled = DRM_CONNECTOR_POLL_HPD;
> > +	else
> > +		sii902x->connector.polled =
> > DRM_CONNECTOR_POLL_CONNECT;
> > +
> > +	drm_mode_connector_attach_encoder(&sii902x->connector,
> > +bridge->encoder);
> > +
> > +	return 0;
> > +}
> > +
> 
> ...
> > +
> > +static int sii902x_probe(struct i2c_client *client,
> > +			 const struct i2c_device_id *id)
> > +{
> > +	struct device *dev = &client->dev;
> > +	unsigned int status = 0;
> > +	struct sii902x *sii902x;
> > +	u8 chipid[4];
> > +	int ret;
> > +
> > +	sii902x = devm_kzalloc(dev, sizeof(*sii902x), GFP_KERNEL);
> > +	if (!sii902x)
> > +		return -ENOMEM;
> > +
> > +	sii902x->i2c = client;
> > +	sii902x->regmap = devm_regmap_init_i2c(client,
> > &sii902x_regmap_config);
> > +	if (IS_ERR(sii902x->regmap))
> > +		return PTR_ERR(sii902x->regmap);
> > +
> > +	sii902x->reset_gpio = devm_gpiod_get(dev, "reset",
> > GPIOD_OUT_LOW);
> > +	if (IS_ERR(sii902x->reset_gpio)) {
> > +		dev_err(dev, "Failed to retrieve/request reset gpio: %ld\n",
> > +			PTR_ERR(sii902x->reset_gpio));
> > +		return PTR_ERR(sii902x->reset_gpio);
> 
> 
> Maybe we can use  "warning" instead of "dev_err" if there is no "reset_gpio" , because some board using CPLD to manage the reset order , they can't reset the HDMI chip independently.

Sure, since it's optional maybe we should use dev_info().

Thanks for your review.

Regards,

Boris

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com