[PATCH RFC] ARM: dts: samsung: add rga-lvds panel in itop elite

[ayaka]

On 08/31/2016 08:30 PM, Andrzej Hajda wrote:
> Hi,
>
>
> On 08/30/2016 12:50 AM, Randy Li wrote:
>> It is actually a lvds panel connected through a rga-lvds bridge.
>> But I really have no idea about what does a port mean in fimd node.
>>
>> Also how should I configure this panel size? I think the i2c found
>> on the panel schematic, but it more likely to be used a touch screen
>> touth. Also the touch screen is not supported in currently driver.
>>
>> Signed-off-by: Randy Li <ayaka at soulik.info>
>> ---
>>   arch/arm/boot/dts/exynos4412-itop-elite.dts | 35 ++++++++++++++++++++++++++---
>>   1 file changed, 32 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts
>> index e1cda54..2d67385 100644
>> --- a/arch/arm/boot/dts/exynos4412-itop-elite.dts
>> +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts
>> @@ -139,6 +139,20 @@
>>   		assigned-clocks = <&clock CLK_MOUT_CAM0>;
>>   		assigned-clock-parents = <&clock CLK_XUSBXTI>;
>>   	};
>> +	
>> +	vcc_sys_lcd: sys-lcd {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc_5v";
>> +		regulator-min-microvolt = <5000000>;
>> +		regulator-max-microvolt = <5000000>;
>> +		gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
>> +	};
>> +
>> +	panel: panel {
>> +		ddc-i2c-bus = <&i2c_3>;
>> +		power-supply = <&vcc_sys_lcd>;
>> +		enable-gpios = <&gpl0 2 GPIO_ACTIVE_HIGH>;
>> +	};
> Panel has no compatible string, which driver will handle this node?
The problem is that, it is panel not supported by kernel. Is it possible 
to support without adding a new driver for it ? I know there is a 
simple-dpi for MIPI, but what is for parallel video or lvds?
> Regards
> Andrzej
The other problem is that I don't how to configure the display-times, 
the datasheet for CLAA070WP03XG should talk about total time, active 
time and blank time for both Horizontal an Vertical time. Does it mean 
the front-porch and sync-len for horizontal and vertical are zero ?

+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               port at 3 {
+                       reg = <3>;
+                       rga_lvds: endpoint {
+                               remote-endpoint = <&panel>;
+                       };
+               };
+       };
+
+       panel: panel at 0 {
+               compatible = "panel-simple";
+
+               power-supply = <&vcc_sys_lcd>;
+               enable-gpios = <&gpl0 2 GPIO_ACTIVE_HIGH>;
+               display-timings {
+                       timing-0 {
+                               clock-frequency = <66770000>;
+                               hactive = <800>;
+                               vactive = <1280>;
+                               hfront-porch = <0>;
+                               hback-porch = <64>;
+                               hsync-len = <0>;
+                               vfront-porch = <0>;
+                               vback-porch = <8>;
+                               vsync-len = <0>;
+                       };