[PATCH v2 13/13] dt-bindings: msm/hdmi: Add HDMI PHY bindings

[Rob Herring]

On Mon, Feb 15, 2016 at 12:23:26PM +0530, Archit Taneja wrote:
> Add HDMI PHY bindings. Update the example to use HDMI PHY.
> 
> Add a missing power-domains property in the HDMI core bindings.
> 
> Cc: devicetree at vger.kernel.org
> Cc: Rob Herring <robh at kernel.org>
> 
> Signed-off-by: Archit Taneja <architt at codeaurora.org>
> ---
>  .../devicetree/bindings/display/msm/hdmi.txt       | 39 +++++++++++++++++++++-
>  1 file changed, 38 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt
> index 379ee2e..4d71910 100644
> --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt
> +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt
> @@ -11,6 +11,7 @@ Required properties:
>  - reg: Physical base address and length of the controller's registers
>  - reg-names: "core_physical"
>  - interrupts: The interrupt signal from the hdmi block.
> +- power-domains: Should be <&mmcc MDSS_GDSC>.
>  - clocks: device clocks
>    See ../clocks/clock-bindings.txt for details.
>  - qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
> @@ -18,6 +19,7 @@ Required properties:
>  - qcom,hdmi-tx-hpd-gpio: hpd pin
>  - core-vdda-supply: phandle to supply regulator
>  - hdmi-mux-supply: phandle to mux regulator
> +- qcom,hdmi-phy: phandle to HDMI PHY device node

Why not use the generic phy binding?

>  
>  Optional properties:
>  - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
> @@ -27,6 +29,27 @@ Optional properties:
>  - pinctrl-0: the default pinctrl state (active)
>  - pinctrl-1: the "sleep" pinctrl state
>  
> +HDMI PHY:
> +Required properties:
> +- compatible: Could be the following
> +  * "qcom,hdmi-phy-8x60"
> +  * "qcom,hdmi-phy-8960"
> +  * "qcom,hdmi-phy-8x74"

No wildcards please. Where's 8994?

> +  * "qcom,hdmi-phy-8996"
> +- reg: Physical base address and length of the registers of the PHY sub blocks.
> +- reg-names: The names of register regions. The following regions are required:
> +  * "hdmi_pll"
> +  * "hdmi_phy"
> +  For HDMI PHY on msm8996, these additional register regions are required:
> +    * "hdmi_tx_l0"
> +    * "hdmi_tx_l1"
> +    * "hdmi_tx_l3"
> +    * "hdmi_tx_l4"
> +- power-domains: Should be <&mmcc MDSS_GDSC>.
> +- clocks: device clocks
> +  See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
> +- core-vdda-supply: phandle to vdda regulator device node
> +
>  Example:
>  
>  / {
> @@ -35,7 +58,7 @@ Example:
>  	hdmi: qcom,hdmi-tx-8960 at 4a00000 {

Node names should be generic, so just "hdmi".

>  		compatible = "qcom,hdmi-tx-8960";
>  		reg-names = "core_physical";
> -		reg = <0x04a00000 0x1000>;
> +		reg = <0x04a00000 0x2f0>;
>  		interrupts = <GIC_SPI 79 0>;
>  		power-domains = <&mmcc MDSS_GDSC>;
>  		clock-names =
> @@ -54,5 +77,19 @@ Example:
>  		pinctrl-names = "default", "sleep";
>  		pinctrl-0 = <&hpd_active  &ddc_active  &cec_active>;
>  		pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
> +
> +		qcom,hdmi-phy = <&hdmi_phy>;
> +	};
> +
> +	hdmi_phy: qcom,hdmi-phy-8960 at 4a00400 {

ditto. phy at ...

> +		compatible = "qcom,hdmi-phy-8960";
> +		reg-names = "hdmi_phy",
> +			    "hdmi_pll";
> +		reg = <0x4a00400 0x60>,
> +		      <0x4a00500 0x100>;
> +		power-domains = <&mmcc MDSS_GDSC>;
> +		clock-names = "slave_iface_clk";
> +		clocks = <&mmcc HDMI_S_AHB_CLK>;
> +		core-vdda-supply = <&pm8921_hdmi_mvs>;
>  	};
>  };
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> hosted by The Linux Foundation
>