[PATCH v3 05/10] drm/rockchip: analogix_dp: add rk3399 eDP support
Yakir Yang
ykk at rock-chips.com
Wed Jun 29 06:58:13 UTC 2016
Sean,
On 06/23/2016 09:48 PM, Sean Paul wrote:
> On Tue, Jun 14, 2016 at 7:46 AM, Yakir Yang <ykk at rock-chips.com> wrote:
>> RK3399 and RK3288 shared the same eDP IP controller, only some light
>> difference with VOP configure and GRF configure.
>>
>> Signed-off-by: Yakir Yang <ykk at rock-chips.com>
>> Acked-by: Mark Yao <mark.yao at rock-chips.com>
>> ---
>> Changes in v3:
>> - Give the "rk3399-edp" a separate line for clarity in document (Tomasz, reviewed at Google Gerrit)
>> [https://chromium-review.googlesource.com/#/c/346314/10/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt@5]
>> - Move 'output_type' setting before the return statement (Tomasz, reviewed at Google Gerrit)
>> [https://chromium-review.googlesource.com/#/c/346314/10/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c@154]
>> - Add the acked flag from Mark.
>>
>> Changes in v2:
>> - rebase with drm-next, fix some conflicts
>>
>> .../bindings/display/bridge/analogix_dp.txt | 1 +
>> .../display/rockchip/analogix_dp-rockchip.txt | 3 +-
>> drivers/gpu/drm/rockchip/analogix_dp-rockchip.c | 33 +++++++++++++++++++++-
>> include/drm/bridge/analogix_dp.h | 1 +
>> 4 files changed, 36 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
>> index 4f2ba8c..4a0f4f7 100644
>> --- a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
>> +++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
>> @@ -5,6 +5,7 @@ Required properties for dp-controller:
>> platform specific such as:
>> * "samsung,exynos5-dp"
>> * "rockchip,rk3288-dp"
>> + * "rockchip,rk3399-edp"
>> -reg:
>> physical base address of the controller and length
>> of memory mapped region.
>> diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt
>> index e832ff9..726c945 100644
>> --- a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt
>> +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt
>> @@ -2,7 +2,8 @@ Rockchip RK3288 specific extensions to the Analogix Display Port
>> ================================
>>
>> Required properties:
>> -- compatible: "rockchip,rk3288-edp";
>> +- compatible: "rockchip,rk3288-edp",
>> + "rockchip,rk3399-edp";
>>
>> - reg: physical base address of the controller and length
>>
>> diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
>> index 315ebba..bcd9ecc 100644
>> --- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
>> +++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
>> @@ -153,6 +153,8 @@ rockchip_dp_drm_encoder_atomic_check(struct drm_encoder *encoder,
>> struct drm_connector_state *conn_state)
>> {
>> struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state);
>> + struct rockchip_dp_device *dp = to_dp(encoder);
>> + int ret;
>>
>> /*
>> * FIXME(Yakir): driver should configure the CRTC output video
>> @@ -167,7 +169,28 @@ rockchip_dp_drm_encoder_atomic_check(struct drm_encoder *encoder,
>> * But if I configure CTRC to RGBaaa, and eDP driver still keep
>> * RGB666 input video mode, then screen would works prefect.
>> */
>> - s->output_mode = ROCKCHIP_OUT_MODE_AAAA;
>> +
>> + ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, encoder);
>> + if (ret < 0)
>> + return 0;
> What is s->output_mode set to in the failure case? How about s->output_type?
I plan to return '-ENODEV' when 'drm_of_encoder_active_endpoint_id'
failed to found, but now i found there is a bug.
When the first time '.atomic_check' was called, encoder have binded to
any crtc, so the 'drm_of_encoder_active_endpoint_id' would be failed.
- If we return failure in this case, then '.atomic_check' would be
called again, then failed again, dead loop.
- If we return zero in this case and set a default
output_mode/output_type, then '.atomic_check' would be successes, then
'crtc->enable' function would use that default setting.
When framework called the 'atomic_check' again, then
'drm_of_encoder_active_endpoint_id' would return the right value, and
'crtc_state would be set rightly. *But* 'vop->enable' wouldn't take care
of those setting, caused it would return directly after detect vop have
been enabled.
This bug need patches both in connector and crtc driver, need more
discuss about this. ;)
Thanks,
- Yakir
>> +
>> + switch (dp->data->chip_type) {
>> + case RK3399_EDP:
>> + /*
>> + * For RK3399, VOP Lit must code the out mode to RGB888,
>> + * VOP Big must code the out mode to RGB10.
>> + */
>> + if (ret)
>> + s->output_mode = ROCKCHIP_OUT_MODE_P888;
>> + else
>> + s->output_mode = ROCKCHIP_OUT_MODE_AAAA;
>> + break;
>> +
>> + default:
>> + s->output_mode = ROCKCHIP_OUT_MODE_AAAA;
>> + break;
>> + }
>> +
> This chunk seems overly complicated. I'd suggest:
>
> s->output_type = DRM_MODE_CONNECTOR_eDP;
> s->output_mode = ROCKCHIP_OUT_MODE_AAAA;
> if (dp->data->chip_type == RK3399_EDP) {
> ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, encoder);
> if (ret > 0)
> s->output_mode = ROCKCHIP_OUT_MODE_P888;
> }
Ah, much clean, done.
Thanks,
- Yakir
>
>> s->output_type = DRM_MODE_CONNECTOR_eDP;
>>
>> return 0;
>> @@ -382,6 +405,13 @@ static const struct dev_pm_ops rockchip_dp_pm_ops = {
>> SET_SYSTEM_SLEEP_PM_OPS(rockchip_dp_suspend, rockchip_dp_resume)
>> };
>>
>> +static const struct rockchip_dp_chip_data rk3399_edp = {
>> + .lcdsel_grf_reg = 0x6250,
>> + .lcdsel_big = 0 | BIT(21),
>> + .lcdsel_lit = BIT(5) | BIT(21),
>> + .chip_type = RK3399_EDP,
>> +};
>> +
>> static const struct rockchip_dp_chip_data rk3288_dp = {
>> .lcdsel_grf_reg = 0x025c,
>> .lcdsel_big = 0 | BIT(21),
>> @@ -391,6 +421,7 @@ static const struct rockchip_dp_chip_data rk3288_dp = {
>>
>> static const struct of_device_id rockchip_dp_dt_ids[] = {
>> {.compatible = "rockchip,rk3288-dp", .data = &rk3288_dp },
>> + {.compatible = "rockchip,rk3399-edp", .data = &rk3399_edp },
>> {}
>> };
>> MODULE_DEVICE_TABLE(of, rockchip_dp_dt_ids);
>> diff --git a/include/drm/bridge/analogix_dp.h b/include/drm/bridge/analogix_dp.h
>> index 06c0250..82b8135 100644
>> --- a/include/drm/bridge/analogix_dp.h
>> +++ b/include/drm/bridge/analogix_dp.h
>> @@ -20,6 +20,7 @@ enum analogix_dp_devtype {
>>
>> enum analogix_dp_sub_devtype {
>> RK3288_DP,
>> + RK3399_EDP,
>> };
>>
>> struct analogix_dp_plat_data {
>> --
>> 1.9.1
>>
>>
>> _______________________________________________
>> dri-devel mailing list
>> dri-devel at lists.freedesktop.org
>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>
>
More information about the dri-devel
mailing list