[PATCHv14 13/18] cec: adv7842: add cec support
Hans Verkuil
hverkuil at xs4all.nl
Fri Mar 25 13:10:11 UTC 2016
From: Hans Verkuil <hans.verkuil at cisco.com>
Add CEC support to the adv7842 driver.
Signed-off-by: Hans Verkuil <hans.verkuil at cisco.com>
---
drivers/media/i2c/Kconfig | 2 +-
drivers/media/i2c/adv7842.c | 323 +++++++++++++++++++++++++++++++++++---------
2 files changed, 261 insertions(+), 64 deletions(-)
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 3d01ffc..11ca81c 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -220,7 +220,7 @@ config VIDEO_ADV7604
config VIDEO_ADV7842
tristate "Analog Devices ADV7842 decoder"
- depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
+ depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API && MEDIA_CEC
select HDMI
---help---
Support for the Analog Devices ADV7842 video decoder.
diff --git a/drivers/media/i2c/adv7842.c b/drivers/media/i2c/adv7842.c
index 7ccb85d..32cfeca 100644
--- a/drivers/media/i2c/adv7842.c
+++ b/drivers/media/i2c/adv7842.c
@@ -39,6 +39,7 @@
#include <linux/workqueue.h>
#include <linux/v4l2-dv-timings.h>
#include <linux/hdmi.h>
+#include <media/cec.h>
#include <media/v4l2-device.h>
#include <media/v4l2-event.h>
#include <media/v4l2-ctrls.h>
@@ -79,6 +80,8 @@ MODULE_LICENSE("GPL");
#define ADV7842_OP_SWAP_CB_CR (1 << 0)
+#define ADV7842_MAX_ADDRS (3)
+
/*
**********************************************************************
*
@@ -142,6 +145,10 @@ struct adv7842_state {
struct v4l2_ctrl *free_run_color_ctrl_manual;
struct v4l2_ctrl *free_run_color_ctrl;
struct v4l2_ctrl *rgb_quantization_range_ctrl;
+
+ u8 cec_addr[ADV7842_MAX_ADDRS];
+ u8 cec_valid_addrs;
+ bool cec_enabled_adap;
};
/* Unsupported timings. This device cannot support 720p30. */
@@ -418,9 +425,9 @@ static inline int cec_write(struct v4l2_subdev *sd, u8 reg, u8 val)
return adv_smbus_write_byte_data(state->i2c_cec, reg, val);
}
-static inline int cec_write_and_or(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val)
+static inline int cec_write_clr_set(struct v4l2_subdev *sd, u8 reg, u8 mask, u8 val)
{
- return cec_write(sd, reg, (cec_read(sd, reg) & mask) | val);
+ return cec_write(sd, reg, (cec_read(sd, reg) & ~mask) | val);
}
static inline int infoframe_read(struct v4l2_subdev *sd, u8 reg)
@@ -696,6 +703,18 @@ adv7842_get_dv_timings_cap(struct v4l2_subdev *sd)
/* ----------------------------------------------------------------------- */
+static u16 adv7842_read_cable_det(struct v4l2_subdev *sd)
+{
+ u8 reg = io_read(sd, 0x6f);
+ u16 val = 0;
+
+ if (reg & 0x02)
+ val |= 1; /* port A */
+ if (reg & 0x01)
+ val |= 2; /* port B */
+ return val;
+}
+
static void adv7842_delayed_work_enable_hotplug(struct work_struct *work)
{
struct delayed_work *dwork = to_delayed_work(work);
@@ -762,50 +781,17 @@ static int edid_write_vga_segment(struct v4l2_subdev *sd)
return 0;
}
-static int edid_spa_location(const u8 *edid)
-{
- u8 d;
-
- /*
- * TODO, improve and update for other CEA extensions
- * currently only for 1 segment (256 bytes),
- * i.e. 1 extension block and CEA revision 3.
- */
- if ((edid[0x7e] != 1) ||
- (edid[0x80] != 0x02) ||
- (edid[0x81] != 0x03)) {
- return -EINVAL;
- }
- /*
- * search Vendor Specific Data Block (tag 3)
- */
- d = edid[0x82] & 0x7f;
- if (d > 4) {
- int i = 0x84;
- int end = 0x80 + d;
- do {
- u8 tag = edid[i]>>5;
- u8 len = edid[i] & 0x1f;
-
- if ((tag == 3) && (len >= 5))
- return i + 4;
- i += len + 1;
- } while (i < end);
- }
- return -EINVAL;
-}
-
static int edid_write_hdmi_segment(struct v4l2_subdev *sd, u8 port)
{
struct i2c_client *client = v4l2_get_subdevdata(sd);
struct adv7842_state *state = to_state(sd);
- const u8 *val = state->hdmi_edid.edid;
- int spa_loc = edid_spa_location(val);
+ const u8 *edid = state->hdmi_edid.edid;
+ int spa_loc;
int err = 0;
int i;
- v4l2_dbg(2, debug, sd, "%s: write EDID on port %c (spa at 0x%x)\n",
- __func__, (port == ADV7842_EDID_PORT_A) ? 'A' : 'B', spa_loc);
+ v4l2_dbg(2, debug, sd, "%s: write EDID on port %c\n",
+ __func__, (port == ADV7842_EDID_PORT_A) ? 'A' : 'B');
/* HPA disable on port A and B */
io_write_and_or(sd, 0x20, 0xcf, 0x00);
@@ -816,24 +802,30 @@ static int edid_write_hdmi_segment(struct v4l2_subdev *sd, u8 port)
if (!state->hdmi_edid.present)
return 0;
+ cec_get_edid_phys_addr(edid, 256, &spa_loc);
+
+ /*
+ * Return an error if no location of the source physical address
+ * was found.
+ */
+ if (spa_loc == 0)
+ return -EINVAL;
+
/* edid segment pointer '0' for HDMI ports */
rep_write_and_or(sd, 0x77, 0xef, 0x00);
for (i = 0; !err && i < 256; i += I2C_SMBUS_BLOCK_MAX)
err = adv_smbus_write_i2c_block_data(state->i2c_edid, i,
- I2C_SMBUS_BLOCK_MAX, val + i);
+ I2C_SMBUS_BLOCK_MAX, edid + i);
if (err)
return err;
- if (spa_loc < 0)
- spa_loc = 0xc0; /* Default value [REF_02, p. 199] */
-
if (port == ADV7842_EDID_PORT_A) {
- rep_write(sd, 0x72, val[spa_loc]);
- rep_write(sd, 0x73, val[spa_loc + 1]);
+ rep_write(sd, 0x72, edid[spa_loc]);
+ rep_write(sd, 0x73, edid[spa_loc + 1]);
} else {
- rep_write(sd, 0x74, val[spa_loc]);
- rep_write(sd, 0x75, val[spa_loc + 1]);
+ rep_write(sd, 0x74, edid[spa_loc]);
+ rep_write(sd, 0x75, edid[spa_loc + 1]);
}
rep_write(sd, 0x76, spa_loc & 0xff);
rep_write_and_or(sd, 0x77, 0xbf, (spa_loc >> 2) & 0x40);
@@ -983,20 +975,11 @@ static int adv7842_s_register(struct v4l2_subdev *sd,
static int adv7842_s_detect_tx_5v_ctrl(struct v4l2_subdev *sd)
{
struct adv7842_state *state = to_state(sd);
- int prev = v4l2_ctrl_g_ctrl(state->detect_tx_5v_ctrl);
- u8 reg_io_6f = io_read(sd, 0x6f);
- int val = 0;
-
- if (reg_io_6f & 0x02)
- val |= 1; /* port A */
- if (reg_io_6f & 0x01)
- val |= 2; /* port B */
+ u16 cable_det = adv7842_read_cable_det(sd);
- v4l2_dbg(1, debug, sd, "%s: 0x%x -> 0x%x\n", __func__, prev, val);
+ v4l2_dbg(1, debug, sd, "%s: 0x%x\n", __func__, cable_det);
- if (val != prev)
- return v4l2_ctrl_s_ctrl(state->detect_tx_5v_ctrl, val);
- return 0;
+ return v4l2_ctrl_s_ctrl(state->detect_tx_5v_ctrl, cable_det);
}
static int find_and_set_predefined_video_timings(struct v4l2_subdev *sd,
@@ -2170,6 +2153,196 @@ static void adv7842_irq_enable(struct v4l2_subdev *sd, bool enable)
}
}
+static void adv7842_cec_tx_raw_status(struct v4l2_subdev *sd, u8 tx_raw_status)
+{
+ struct v4l2_subdev_cec_tx_done tx_done = {};
+
+ if ((cec_read(sd, 0x11) & 0x01) == 0) {
+ v4l2_dbg(1, debug, sd, "%s: tx raw: tx disabled\n", __func__);
+ return;
+ }
+
+ if (tx_raw_status & 0x02) {
+ v4l2_dbg(1, debug, sd, "%s: tx raw: arbitration lost\n",
+ __func__);
+ tx_done.status = CEC_TX_STATUS_ARB_LOST;
+ tx_done.arb_lost_cnt = 1;
+ v4l2_subdev_notify(sd, V4L2_SUBDEV_CEC_TX_DONE, &tx_done);
+ return;
+ }
+ if (tx_raw_status & 0x04) {
+ v4l2_dbg(1, debug, sd, "%s: tx raw: retry failed\n", __func__);
+ /*
+ * We set this status bit since this hardware performs
+ * retransmissions.
+ */
+ tx_done.status = CEC_TX_STATUS_MAX_RETRIES;
+ tx_done.nack_cnt = cec_read(sd, 0x14) & 0xf;
+ if (tx_done.nack_cnt)
+ tx_done.status |= CEC_TX_STATUS_NACK;
+ tx_done.low_drive_cnt = cec_read(sd, 0x14) >> 4;
+ if (tx_done.low_drive_cnt)
+ tx_done.status |= CEC_TX_STATUS_LOW_DRIVE;
+ v4l2_subdev_notify(sd, V4L2_SUBDEV_CEC_TX_DONE, &tx_done);
+ return;
+ }
+ if (tx_raw_status & 0x01) {
+ v4l2_dbg(1, debug, sd, "%s: tx raw: ready ok\n", __func__);
+ tx_done.status = CEC_TX_STATUS_OK;
+ v4l2_subdev_notify(sd, V4L2_SUBDEV_CEC_TX_DONE, &tx_done);
+ return;
+ }
+}
+
+static void adv7842_cec_isr(struct v4l2_subdev *sd, bool *handled)
+{
+ u8 cec_irq;
+
+ /* cec controller */
+ cec_irq = io_read(sd, 0x93) & 0x0f;
+ if (!cec_irq)
+ return;
+
+ v4l2_dbg(1, debug, sd, "%s: cec: irq 0x%x\n", __func__, cec_irq);
+ adv7842_cec_tx_raw_status(sd, cec_irq);
+ if (cec_irq & 0x08) {
+ struct cec_msg msg;
+
+ msg.len = cec_read(sd, 0x25) & 0x1f;
+ if (msg.len > 16)
+ msg.len = 16;
+
+ if (msg.len) {
+ u8 i;
+
+ for (i = 0; i < msg.len; i++)
+ msg.msg[i] = cec_read(sd, i + 0x15);
+ cec_write(sd, 0x26, 0x01); /* re-enable rx */
+ v4l2_subdev_notify(sd, V4L2_SUBDEV_CEC_RX_MSG, &msg);
+ }
+ }
+
+ io_write(sd, 0x94, cec_irq);
+
+ if (handled)
+ *handled = true;
+}
+
+static unsigned adv7842_cec_adap_available_log_addrs(struct v4l2_subdev *sd)
+{
+ return ADV7842_MAX_ADDRS;
+}
+
+static int adv7842_cec_adap_enable(struct v4l2_subdev *sd, bool enable)
+{
+ struct adv7842_state *state = to_state(sd);
+
+ if (!state->cec_enabled_adap && enable) {
+ cec_write_clr_set(sd, 0x2a, 0x01, 0x01); /* power up cec */
+ cec_write(sd, 0x2c, 0x01); /* cec soft reset */
+ cec_write_clr_set(sd, 0x11, 0x01, 0); /* initially disable tx */
+ /* enabled irqs: */
+ /* tx: ready */
+ /* tx: arbitration lost */
+ /* tx: retry timeout */
+ /* rx: ready */
+ io_write_clr_set(sd, 0x96, 0x0f, 0x0f);
+ cec_write(sd, 0x26, 0x01); /* enable rx */
+ } else if (state->cec_enabled_adap && !enable) {
+ /* disable cec interrupts */
+ io_write_clr_set(sd, 0x96, 0x0f, 0x00);
+ /* disable address mask 1-3 */
+ cec_write_clr_set(sd, 0x27, 0x70, 0x00);
+ /* power down cec section */
+ cec_write_clr_set(sd, 0x2a, 0x01, 0x00);
+ state->cec_valid_addrs = 0;
+ }
+ state->cec_enabled_adap = enable;
+ return 0;
+}
+
+static int adv7842_cec_adap_log_addr(struct v4l2_subdev *sd, u8 addr)
+{
+ struct adv7842_state *state = to_state(sd);
+ unsigned i, free_idx = ADV7842_MAX_ADDRS;
+
+ if (!state->cec_enabled_adap)
+ return -EIO;
+
+ if (addr == CEC_LOG_ADDR_INVALID) {
+ cec_write_clr_set(sd, 0x27, 0x70, 0);
+ state->cec_valid_addrs = 0;
+ return 0;
+ }
+
+ for (i = 0; i < ADV7842_MAX_ADDRS; i++) {
+ bool is_valid = state->cec_valid_addrs & (1 << i);
+
+ if (free_idx == ADV7842_MAX_ADDRS && !is_valid)
+ free_idx = i;
+ if (is_valid && state->cec_addr[i] == addr)
+ return 0;
+ }
+ if (i == ADV7842_MAX_ADDRS) {
+ i = free_idx;
+ if (i == ADV7842_MAX_ADDRS)
+ return -ENXIO;
+ }
+ state->cec_addr[i] = addr;
+ state->cec_valid_addrs |= 1 << i;
+
+ switch (i) {
+ case 0:
+ /* enable address mask 0 */
+ cec_write_clr_set(sd, 0x27, 0x10, 0x10);
+ /* set address for mask 0 */
+ cec_write_clr_set(sd, 0x28, 0x0f, addr);
+ break;
+ case 1:
+ /* enable address mask 1 */
+ cec_write_clr_set(sd, 0x27, 0x20, 0x20);
+ /* set address for mask 1 */
+ cec_write_clr_set(sd, 0x28, 0xf0, addr << 4);
+ break;
+ case 2:
+ /* enable address mask 2 */
+ cec_write_clr_set(sd, 0x27, 0x40, 0x40);
+ /* set address for mask 1 */
+ cec_write_clr_set(sd, 0x29, 0x0f, addr);
+ break;
+ }
+ return 0;
+}
+
+static int adv7842_cec_adap_transmit(struct v4l2_subdev *sd, u8 attempts,
+ u32 signal_free_time, struct cec_msg *msg)
+{
+ u8 len = msg->len;
+ unsigned i;
+
+ /*
+ * The number of retries is the number of attempts - 1, but retry
+ * at least once. It's not clear if a value of 0 is allowed, so
+ * let's do at least one retry.
+ */
+ cec_write_clr_set(sd, 0x12, 0x70, max(1, attempts - 1) << 4);
+
+ if (len > 16) {
+ v4l2_err(sd, "%s: len exceeded 16 (%d)\n", __func__, len);
+ return -EINVAL;
+ }
+
+ /* write data */
+ for (i = 0; i < len; i++)
+ cec_write(sd, i, msg->msg[i]);
+
+ /* set length (data + header) */
+ cec_write(sd, 0x10, len);
+ /* start transmit, enable tx */
+ cec_write(sd, 0x11, 0x01);
+ return 0;
+}
+
static int adv7842_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
{
struct adv7842_state *state = to_state(sd);
@@ -2241,6 +2414,9 @@ static int adv7842_isr(struct v4l2_subdev *sd, u32 status, bool *handled)
*handled = true;
}
+ /* cec */
+ adv7842_cec_isr(sd, handled);
+
/* tx 5v detect */
if (irq_status[2] & 0x3) {
v4l2_dbg(1, debug, sd, "%s: irq tx_5v\n", __func__);
@@ -2321,10 +2497,12 @@ static int adv7842_set_edid(struct v4l2_subdev *sd, struct v4l2_edid *e)
case ADV7842_EDID_PORT_A:
case ADV7842_EDID_PORT_B:
memset(&state->hdmi_edid.edid, 0, 256);
- if (e->blocks)
+ if (e->blocks) {
state->hdmi_edid.present |= 0x04 << e->pad;
- else
+ } else {
state->hdmi_edid.present &= ~(0x04 << e->pad);
+ adv7842_s_detect_tx_5v_ctrl(sd);
+ }
memcpy(&state->hdmi_edid.edid, e->edid, 128 * e->blocks);
err = edid_write_hdmi_segment(sd, e->pad);
break;
@@ -2509,8 +2687,19 @@ static int adv7842_cp_log_status(struct v4l2_subdev *sd)
v4l2_info(sd, "HPD A %s, B %s\n",
reg_io_0x21 & 0x02 ? "enabled" : "disabled",
reg_io_0x21 & 0x01 ? "enabled" : "disabled");
- v4l2_info(sd, "CEC %s\n", !!(cec_read(sd, 0x2a) & 0x01) ?
+ v4l2_info(sd, "CEC: %s\n", state->cec_enabled_adap ?
"enabled" : "disabled");
+ if (state->cec_enabled_adap) {
+ int i;
+
+ for (i = 0; i < ADV7842_MAX_ADDRS; i++) {
+ bool is_valid = state->cec_valid_addrs & (1 << i);
+
+ if (is_valid)
+ v4l2_info(sd, "CEC Logical Address: 0x%x\n",
+ state->cec_addr[i]);
+ }
+ }
v4l2_info(sd, "-----Signal status-----\n");
if (state->hdmi_port_a) {
@@ -3061,6 +3250,13 @@ static const struct v4l2_subdev_video_ops adv7842_video_ops = {
.query_dv_timings = adv7842_query_dv_timings,
};
+static const struct v4l2_subdev_cec_ops adv7842_cec_ops = {
+ .adap_available_log_addrs = adv7842_cec_adap_available_log_addrs,
+ .adap_enable = adv7842_cec_adap_enable,
+ .adap_log_addr = adv7842_cec_adap_log_addr,
+ .adap_transmit = adv7842_cec_adap_transmit,
+};
+
static const struct v4l2_subdev_pad_ops adv7842_pad_ops = {
.enum_mbus_code = adv7842_enum_mbus_code,
.get_fmt = adv7842_get_format,
@@ -3075,6 +3271,7 @@ static const struct v4l2_subdev_ops adv7842_ops = {
.core = &adv7842_core_ops,
.video = &adv7842_video_ops,
.pad = &adv7842_pad_ops,
+ .cec = &adv7842_cec_ops,
};
/* -------------------------- custom ctrls ---------------------------------- */
@@ -3361,7 +3558,7 @@ static int adv7842_remove(struct i2c_client *client)
struct adv7842_state *state = to_state(sd);
adv7842_irq_enable(sd, false);
-
+ adv7842_cec_adap_enable(sd, false);
cancel_delayed_work(&state->delayed_work_enable_hotplug);
destroy_workqueue(state->work_queues);
v4l2_device_unregister_subdev(sd);
--
2.7.0
More information about the dri-devel
mailing list