[PATCH v3 7/7] dt-bindings: drm/bridge: Update bindings for ADV7533

[Xinliang Liu]

On 17 May 2016 at 11:43, Archit Taneja <architt at codeaurora.org> wrote:
>
>
> On 05/16/2016 05:31 PM, Laurent Pinchart wrote:
>>
>> Hi Archit,
>>
>> On Friday 22 Apr 2016 11:10:18 Archit Taneja wrote:
>>>
>>> On 04/22/2016 04:02 AM, Laurent Pinchart wrote:
>>>>
>>>> On Wednesday 09 Mar 2016 16:27:18 Archit Taneja wrote:
>>>>>
>>>>> Add description of ADV7533. Add the required and optional properties
>>>>> that
>>>>> are specific to it.
>>>>>
>>>>> Cc: devicetree at vger.kernel.org
>>>>> Cc: Rob Herring <robh at kernel.org>
>>>>>
>>>>> Signed-off-by: Archit Taneja <architt at codeaurora.org>
>>>>> ---
>>>>>
>>>>> .../bindings/display/bridge/adi,adv7511.txt        | 25
>>>>> ++++++++++++-----
>>>>> 1 file changed, 20 insertions(+), 5 deletions(-)
>>>>>
>>>>> diff --git
>>>>> a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>>>>> b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>>>>> index
>>>>> 96c25ee..420da5a 100644
>>>>> --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>>>>> +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
>>
>>
>> [snip]
>>
>>>>> +- adi,disable-timing-generator: Only for ADV7533. Disables the
>>>>> internal
>>>>> timing
>>>>> +  generator. The chip will rely on the sync signals in the DSI data
>>>>> lanes,
>>>>> +  rather than generate its own timings for HDMI output.
>>>>
>>>>
>>>> Isn't that something that should be selectable at runtime ?
>>>
>>>
>>> The timing generator can be enabled/disabled at runtime. Although, we
>>> don't have a way to tell the driver whether we want to keep it enabled
>>> or not.
>>>
>>> It's a hardware feature that works well on most platforms, but not on
>>> all. In particular, it works well on DB410c, but causes issues with
>>> the Hikey 96 board. The DSI host on Hikey has different clock sources
>>> that generate the display controller's pixel clock and DSI byte clock,
>>> whereas the Qualcomm SoC uses the same source. My guess is that the
>>> ADV7533's timing generator doesn't like it when the pixel data and
>>> clock are out of phase or something.
>>>
>>> Since it is a hardware feature which needs tweaking, I thought it
>>> qualified as a DT property.
>>
>>
>> The fact that a hardware generator is present is certainly describes the
>> hardware, but I'm not sure whether to enable it or not also qualifies as a
>> hardware feature.
>>
>> Are there use cases for using the timing generator conditionally on a
>> given
>> board ? As you implement support for disabling it, I assume it's not
>> mandatory. What feature(s) do we lose if we keep it disabled ?
>>
>
> The spec says it's recommended to use the internal timing generator. In
> the case of db410c, I observe an unstable output/flicker for certain
> modes if I don't enable it.
>
> In the case of hikey platform, it's the other way round.
>
> Xinliang, could you describe the problems you face when the timing
> generator is enabled?

Yes,  opening the timing generator of ADV7533 can benefit the HDMI
output signal.
But, for some circumstances, we need to disable timing generator:
To make modes work, the timing parameters (hfp, hbp, etc.) used by
ADV7533 timing generator should match the ones used in DSI.
If the timing parameters changed in DSI and these changing  timing
parameters can't pass to ADV7533, then it need to disable the timing
generator of ADV7533 to make mode work.
Some modes in HiKey is in this case.

Thanks,
-xinliang

>
>
> Thanks,
> Archit
>
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> hosted by The Linux Foundation