[PATCH RFC] drm: Add a new connector atomic property for link status
Daniel Vetter
daniel at ffwll.ch
Wed Nov 23 08:09:28 UTC 2016
On Tue, Nov 22, 2016 at 09:27:35PM -0500, Sean Paul wrote:
> On Tue, Nov 22, 2016 at 8:30 PM, Manasi Navare
> <manasi.d.navare at intel.com> wrote:
> > This is RFC patch for adding a connector link-status property
> > and making it atomic by adding it to the drm_connector_state.
> > This is to make sure its wired properly in drm_atomic_connector_set_property
> > and drm_atomic_connector_get_property functions.
> >
>
> Thanks for sending this. We ran into some re-training awkwardness
> recently, and I
> was hoping for such a patch.
>
> > Cc: Jani Nikula <jani.nikula at linux.intel.com>
> > Cc: Daniel Vetter <daniel.vetter at intel.com>
> > Cc: Ville Syrjala <ville.syrjala at linux.intel.com>
> > Cc: Chris Wilson <chris at chris-wilson.co.uk>
> > Signed-off-by: Manasi Navare <manasi.d.navare at intel.com>
> > ---
> > drivers/gpu/drm/drm_atomic.c | 5 ++++
> > drivers/gpu/drm/drm_connector.c | 65 +++++++++++++++++++++++++++++++++++++++--
> > include/drm/drm_connector.h | 12 +++++++-
> > include/drm/drm_mode_config.h | 5 ++++
> > include/uapi/drm/drm_mode.h | 4 +++
> > 5 files changed, 88 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/drm_atomic.c b/drivers/gpu/drm/drm_atomic.c
> > index 89737e4..644d19f 100644
> > --- a/drivers/gpu/drm/drm_atomic.c
> > +++ b/drivers/gpu/drm/drm_atomic.c
> > @@ -1087,6 +1087,9 @@ int drm_atomic_connector_set_property(struct drm_connector *connector,
> > * now?) atomic writes to DPMS property:
> > */
> > return -EINVAL;
> > + } else if (property == config->link_status_property) {
> > + state->link_status = val;
I think we should have a check here to make sure userspace never tries to
set this from "GOOD" to "BAD". "BAD" to "BAD" we need to allow, since with
atomic userspace is supposed to be able to just restore everything to what
it was.
I don't think trying to set it to "BAD" should cause an error though, just
silently keep the link status at "GOOG". So:
/* Never downgrade from GOOD to BAD on userspace's request here,
* only hw issues can do that. */
if (state->link_status == GOOD)
return 0;
state->link_status = val;
return 0;
> > + return 0;
> > } else if (connector->funcs->atomic_set_property) {
> > return connector->funcs->atomic_set_property(connector,
> > state, property, val);
> > @@ -1135,6 +1138,8 @@ static void drm_atomic_connector_print_state(struct drm_printer *p,
> > *val = (state->crtc) ? state->crtc->base.id : 0;
> > } else if (property == config->dpms_property) {
> > *val = connector->dpms;
> > + } else if (property == config->link_status_property) {
> > + *val = state->link_status;
> > } else if (connector->funcs->atomic_get_property) {
> > return connector->funcs->atomic_get_property(connector,
> > state, property, val);
> > diff --git a/drivers/gpu/drm/drm_connector.c b/drivers/gpu/drm/drm_connector.c
> > index 5a45262..4576c9f 100644
> > --- a/drivers/gpu/drm/drm_connector.c
> > +++ b/drivers/gpu/drm/drm_connector.c
> > @@ -243,6 +243,10 @@ int drm_connector_init(struct drm_device *dev,
> > drm_object_attach_property(&connector->base,
> > config->dpms_property, 0);
> >
> > + drm_object_attach_property(&connector->base,
> > + config->link_status_property,
> > + 0);
> > +
> > if (drm_core_check_feature(dev, DRIVER_ATOMIC)) {
> > drm_object_attach_property(&connector->base, config->prop_crtc_id, 0);
> > }
> > @@ -506,6 +510,12 @@ const char *drm_get_subpixel_order_name(enum subpixel_order order)
> > };
> > DRM_ENUM_NAME_FN(drm_get_dpms_name, drm_dpms_enum_list)
> >
> > +static const struct drm_prop_enum_list drm_link_status_enum_list[] = {
> > + { DRM_MODE_LINK_STATUS_GOOD, "Good" },
> > + { DRM_MODE_LINK_STATUS_BAD, "Bad" },
> > +};
> > +DRM_ENUM_NAME_FN(drm_get_link_status_name, drm_link_status_enum_list)
> > +
> > /**
> > * drm_display_info_set_bus_formats - set the supported bus formats
> > * @info: display info to store bus formats in
> > @@ -616,7 +626,7 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,
> > * path property the MST manager created. Userspace cannot change this
> > * property.
> > * TILE:
> > - * Connector tile group property to indicate how a set of DRM connector
> > + * Connector tile group property to indicate how a set of DRM connector
>
> keyboard slip here
>
> > * compose together into one logical screen. This is used by both high-res
> > * external screens (often only using a single cable, but exposing multiple
> > * DP MST sinks), or high-res integrated panels (like dual-link DSI) which
> > @@ -625,7 +635,14 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,
> > * tiling and virtualize both &drm_crtc and &drm_plane if needed. Drivers
> > * should update this value using drm_mode_connector_set_tile_property().
> > * Userspace cannot change this property.
> > - *
> > + * link-status:
> > + * Connector link-status property to indicate the status of link during
> > + * the modeset. The default value of link-status is "GOOD". If something
> > + * fails during modeset, the kernel driver can set this to "BAD", prune
> > + * the mode list based on new link parameters and send a hotplug uevent
> > + * to notify userspace to re-check the valid modes through GET_CONNECTOR
> > + * IOCTL and redo a modeset. Drivers should update this value using
> > + * drm_mode_connector_set_link_status_property().
> > * Connectors also have one standardized atomic property:
> > *
> > * CRTC_ID:
> > @@ -666,6 +683,13 @@ int drm_connector_create_standard_properties(struct drm_device *dev)
> > return -ENOMEM;
> > dev->mode_config.tile_property = prop;
> >
> > + prop = drm_property_create_enum(dev, DRM_MODE_PROP_ATOMIC, "link-status",
> > + drm_link_status_enum_list,
> > + ARRAY_SIZE(drm_link_status_enum_list));
> > + if (!prop)
> > + return -ENOMEM;
> > + dev->mode_config.link_status_property = prop;
> > +
> > return 0;
> > }
> >
> > @@ -995,6 +1019,43 @@ int drm_mode_connector_update_edid_property(struct drm_connector *connector,
> > }
> > EXPORT_SYMBOL(drm_mode_connector_update_edid_property);
> >
> > +/**
> > + * drm_mode_connector_set_link_status_property - Set link status property of a connector
> > + * @connector: drm connector
> > + * @link_status: new value of link status property (0: Good, 1: Bad)
> > + *
> > + * In usual working scenario, this link status property will always be set to
> > + * "GOOD". If something fails during or after a mode set, the kernel driver should
> > + * set this link status property to "BAD" and prune the mode list based on new
>
> Does the mode list really *need* to be pruned? In the case of needing
> to re-train a DP link,
> it seems like we should be able to set this BAD and keep the modelist
> as-is (since the sink
> hasn't changed)
Well, if you prune it with the same constraints as before, no additional
modes will be removed and the same list is there. Pruning here refers to
the ->mode_valid step as done in e.g. drm_helper_probe_single_connector_modes.
We might want to be a bit more explicit here perhaps? Have some good
proposal text to insert?
>
> > + * information. The caller then needs to send a hotplug uevent for userspace to
> > + * re-check the valid modes through GET_CONNECTOR_IOCTL and retry modeset.
>
> extra space
>
> > + *
> > + * Note that a lot of existing userspace do not handle this property.
> > + * Drivers can therefore not rely on userspace to fix up everything and
> > + * should try to handle issues (like just re-training a link) without
> > + * userspace's intervention. This should only be used when the current mode
> > + * fails and userspace must select a different display mode.
>
> Hmm, I suppose this answers my last question. It's too bad we can't
> rely on this, since we'll
> just end up with each driver rolling their own re-training logic on
> top of possibly supporting
> this (but probably not, since it's really just overhead). Perhaps this
> is an overly pessimistic
> view?
You can forgo any re-training of course, that should work too. It's just
that DP spec and everyone else seem to recommend to at least do some
minimal effort (or maybe even upfront link training) here. But totally not
doing anything if the link is bad should be ok too (and probably really
simple to implement for drivers, maybe even with a dp_hpd_handler() helper
function which checks link status and set link-status to bad&fires off the
uevent if needed.
Again, do you have some sample prose to add here to clarify this?
Thanks for taking a look at this.
Cheers, Daniel
> > + * The DRM driver can chose to not modify property and keep link status
> > + * as "GOOD" always to keep the user experience same as it currently is.
> > + *
> > + * The reason for adding this property is to handle link training failures, but
> > + * it is not limited to DP or link training. For example, if we implement
> > + * asynchronous setcrtc, this property can be used to report any failures in that.
> > + */
> > +void drm_mode_connector_set_link_status_property(struct drm_connector *connector,
> > + uint64_t link_status)
> > +{
> > + struct drm_device *dev = connector->dev;
> > +
> > + /* Make sure the mutex is grabbed */
> > + lockdep_assert_held(&dev->mode_config.mutex);
> > + connector->link_status = link_status;
> > + drm_object_property_set_value(&connector->base,
> > + dev->mode_config.link_status_property,
> > + link_status);
> > +}
> > +EXPORT_SYMBOL(drm_mode_connector_set_link_status_property);
> > +
> > int drm_mode_connector_set_obj_prop(struct drm_mode_object *obj,
> > struct drm_property *property,
> > uint64_t value)
> > diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
> > index 34f9741..3d513ab 100644
> > --- a/include/drm/drm_connector.h
> > +++ b/include/drm/drm_connector.h
> > @@ -213,6 +213,9 @@ struct drm_connector_state {
> >
> > struct drm_encoder *best_encoder;
> >
> > + /* Connector Link status */
> > + unsigned int link_status;
> > +
> > struct drm_atomic_state *state;
> > };
> >
> > @@ -695,6 +698,12 @@ struct drm_connector {
> > uint8_t num_h_tile, num_v_tile;
> > uint8_t tile_h_loc, tile_v_loc;
> > uint16_t tile_h_size, tile_v_size;
> > +
> > + /* Connector Link status
> > + * 0: If the link is Good
> > + * 1: If the link is Bad
> > + */
> > + int link_status;
> > };
> >
> > #define obj_to_connector(x) container_of(x, struct drm_connector, base)
> > @@ -767,12 +776,13 @@ int drm_mode_create_tv_properties(struct drm_device *dev,
> > int drm_mode_create_scaling_mode_property(struct drm_device *dev);
> > int drm_mode_create_aspect_ratio_property(struct drm_device *dev);
> > int drm_mode_create_suggested_offset_properties(struct drm_device *dev);
> > -
>
> lost a line here
>
> > int drm_mode_connector_set_path_property(struct drm_connector *connector,
> > const char *path);
> > int drm_mode_connector_set_tile_property(struct drm_connector *connector);
> > int drm_mode_connector_update_edid_property(struct drm_connector *connector,
> > const struct edid *edid);
> > +void drm_mode_connector_set_link_status_property(struct drm_connector *connector,
> > + uint64_t link_status);
> >
> > /**
> > * struct drm_tile_group - Tile group metadata
> > diff --git a/include/drm/drm_mode_config.h b/include/drm/drm_mode_config.h
> > index bf9991b..86faee4 100644
> > --- a/include/drm/drm_mode_config.h
> > +++ b/include/drm/drm_mode_config.h
> > @@ -431,6 +431,11 @@ struct drm_mode_config {
> > */
> > struct drm_property *tile_property;
> > /**
> > + * @link_status_property: Default connector property for link status
> > + * of a connector
> > + */
> > + struct drm_property *link_status_property;
> > + /**
> > * @plane_type_property: Default plane property to differentiate
> > * CURSOR, PRIMARY and OVERLAY legacy uses of planes.
> > */
> > diff --git a/include/uapi/drm/drm_mode.h b/include/uapi/drm/drm_mode.h
> > index 728790b..309c478 100644
> > --- a/include/uapi/drm/drm_mode.h
> > +++ b/include/uapi/drm/drm_mode.h
> > @@ -123,6 +123,10 @@
> > #define DRM_MODE_DIRTY_ON 1
> > #define DRM_MODE_DIRTY_ANNOTATE 2
> >
> > +/* Link Status options */
> > +#define DRM_MODE_LINK_STATUS_GOOD 0
> > +#define DRM_MODE_LINK_STATUS_BAD 1
> > +
> > struct drm_mode_modeinfo {
> > __u32 clock;
> > __u16 hdisplay;
> > --
> > 1.9.1
> >
> > _______________________________________________
> > dri-devel mailing list
> > dri-devel at lists.freedesktop.org
> > https://lists.freedesktop.org/mailman/listinfo/dri-devel
> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
More information about the dri-devel
mailing list