[PATCH v2] drm/mediatek: fixed the calc method of data rate per lane

Jitao Shi jitao.shi at mediatek.com
Wed Oct 26 09:07:12 UTC 2016


On Wed, 2016-10-26 at 14:41 +0800, CK Hu wrote:
> Hi, Jitao:
> 
> On Tue, 2016-10-25 at 13:40 +0800, Jitao Shi wrote:
> > Tune dsi frame rate by pixel clock, dsi add some extra signal (i.e. Tlpx,
> > Ths-prepare, Ths-zero, Ths-trail,Ths-exit) when enter and exit LP mode, this
> > signal will cause h-time larger than normal and reduce FPS.
> > Need to multiply a coefficient to offset the extra signal's effect.
> > coefficient = ((htotal*bpp/lane_number)+Tlpx+Ths_prep+Ths_zero+Ths_trail+
> >                 Ths_exit)/(htotal*bpp/lane_number))
> > 
> > Signed-off-by: Jitao Shi <jitao.shi at mediatek.com>
> > ---
> > Change since v1:
> >  - phy_timing2 and phy_timing3 refer clock cycle time.
> >  - define values of LPX HS_PRPR HS_ZERO HS_TRAIL TA_GO TA_SURE TA_GET DA_HS_EXIT
> > ---
> >  drivers/gpu/drm/mediatek/mtk_dsi.c |  103 +++++++++++++++++++++++-------------
> >  1 file changed, 67 insertions(+), 36 deletions(-)
> > 
> 
> [snip...]
> 
> >  
> > -static void dsi_phy_timconfig(struct mtk_dsi *dsi)
> > +static void dsi_phy_timconfig(struct mtk_dsi *dsi, u32 phy_timing0,
> > +			      u32 phy_timing1, u32 phy_timing2,
> > +			      u32 phy_timing3)
> >  {
> > -	u32 timcon0, timcon1, timcon2, timcon3;
> > -	unsigned int ui, cycle_time;
> > -	unsigned int lpx;
> > -
> > -	ui = 1000 / dsi->data_rate + 0x01;
> > -	cycle_time = 8000 / dsi->data_rate + 0x01;
> > -	lpx = 5;
> > -
> > -	timcon0 = (8 << 24) | (0xa << 16) | (0x6 << 8) | lpx;
> > -	timcon1 = (7 << 24) | (5 * lpx << 16) | ((3 * lpx) / 2) << 8 |
> > -		  (4 * lpx);
> > -	timcon2 = ((NS_TO_CYCLE(0x64, cycle_time) + 0xa) << 24) |
> > -		  (NS_TO_CYCLE(0x150, cycle_time) << 16);
> > -	timcon3 = (2 * lpx) << 16 | NS_TO_CYCLE(80 + 52 * ui, cycle_time) << 8 |
> > -		   NS_TO_CYCLE(0x40, cycle_time);
> > -
> > -	writel(timcon0, dsi->regs + DSI_PHY_TIMECON0);
> > -	writel(timcon1, dsi->regs + DSI_PHY_TIMECON1);
> > -	writel(timcon2, dsi->regs + DSI_PHY_TIMECON2);
> > -	writel(timcon3, dsi->regs + DSI_PHY_TIMECON3);
> 
> Why do you move these calculation to mtk_dsi_poweron()? You can keep
> calculation here and just do some modification.
> 
> Regards,
> CK

Thanks for your review. I'll fix it in next patchset.

Best Regards
jitao

> 
> > +	writel(phy_timing0, dsi->regs + DSI_PHY_TIMECON0);
> > +	writel(phy_timing1, dsi->regs + DSI_PHY_TIMECON1);
> > +	writel(phy_timing2, dsi->regs + DSI_PHY_TIMECON2);
> > +	writel(phy_timing3, dsi->regs + DSI_PHY_TIMECON3);
> >  }
> >  
> >  static void mtk_dsi_enable(struct mtk_dsi *dsi)
> > @@ -202,19 +188,51 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
> >  {
> >  	struct device *dev = dsi->dev;
> >  	int ret;
> > +	u64 bit_clock, total_bits;
> > +	u32 htotal, htotal_bits, bit_per_pixel, overhead_cycles, overhead_bits;
> > +	u32 phy_timing0, phy_timing1, phy_timing2, phy_timing3;
> > +	u32 ui, cycle_time;
> >  
> >  	if (++dsi->refcount != 1)
> >  		return 0;
> >  
> > +	switch (dsi->format) {
> > +	case MIPI_DSI_FMT_RGB565:
> > +		bit_per_pixel = 16;
> > +		break;
> > +	case MIPI_DSI_FMT_RGB666_PACKED:
> > +		bit_per_pixel = 18;
> > +		break;
> > +	case MIPI_DSI_FMT_RGB666:
> > +	case MIPI_DSI_FMT_RGB888:
> > +	default:
> > +		bit_per_pixel = 24;
> > +		break;
> > +	}
> > +	/**
> > +	 * data_rate = (pixel_clock) * bit_per_pixel * mipi_ratio / lane_num;
> > +	 * vm.pixelclock is Khz, data_rata unit is Hz, so need to multiply 1000
> > +	 * mipi_ratio is (htotal * byte_per_pixel / lane_num + Tlpx + Ths_prep
> > +	 *		  + Thstrail + Ths_exit + Ths_zero) /
> > +	 *		 (htotal * byte_per_pixel /lane_number)
> > +	 */
> > +	bit_clock = dsi->vm.pixelclock * 1000 * bit_per_pixel;
> > +	htotal = dsi->vm.hactive + dsi->vm.hback_porch + dsi->vm.hfront_porch +
> > +		 dsi->vm.hsync_len;
> > +	htotal_bits = htotal * bit_per_pixel;
> > +
> >  	/**
> > -	 * data_rate = (pixel_clock / 1000) * pixel_dipth * mipi_ratio;
> > -	 * pixel_clock unit is Khz, data_rata unit is MHz, so need divide 1000.
> > -	 * mipi_ratio is mipi clk coefficient for balance the pixel clk in mipi.
> > -	 * we set mipi_ratio is 1.05.
> > +	 * overhead = lpx + hs_prepare + hs_zero + hs_trail + hs_exit
> >  	 */
> > -	dsi->data_rate = dsi->vm.pixelclock * 3 * 21 / (1 * 1000 * 10);
> > +	overhead_cycles = LPX + (HS_PRPR >> 8) + (HS_ZERO >> 16) +
> > +			  (HS_TRAIL >> 24) + (DA_HS_EXIT >> 24);
> > +	overhead_bits = overhead_cycles * dsi->lanes * 8;
> > +	total_bits = htotal_bits + overhead_bits;
> >  
> > -	ret = clk_set_rate(dsi->hs_clk, dsi->data_rate * 1000000);
> > +	dsi->data_rate = DIV_ROUND_UP_ULL(bit_clock * total_bits,
> > +					  htotal_bits * dsi->lanes);
> > +
> > +	ret = clk_set_rate(dsi->hs_clk, dsi->data_rate);
> >  	if (ret < 0) {
> >  		dev_err(dev, "Failed to set data rate: %d\n", ret);
> >  		goto err_refcount;
> > @@ -236,7 +254,20 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
> >  
> >  	mtk_dsi_enable(dsi);
> >  	mtk_dsi_reset(dsi);
> > -	dsi_phy_timconfig(dsi);
> > +
> > +	ui = 1000 / dsi->data_rate + 0x01;
> > +	cycle_time = 8000 / dsi->data_rate + 0x01;
> > +
> > +	phy_timing0 = LPX | HS_PRPR | HS_ZERO | HS_TRAIL;
> > +	phy_timing1 = TA_GO | TA_SURE | TA_GET | DA_HS_EXIT;
> > +	phy_timing2 = ((NS_TO_CYCLE(0x64, cycle_time) + 0xa) << 24) |
> > +		      (NS_TO_CYCLE(0x150, cycle_time) << 16);
> > +	phy_timing3 = (2 * LPX) << 16 |
> > +		      NS_TO_CYCLE(80 + 52 * ui, cycle_time) << 8 |
> > +		      NS_TO_CYCLE(0x40, cycle_time);
> > +
> > +	dsi_phy_timconfig(dsi, phy_timing0, phy_timing1, phy_timing2,
> > +			  phy_timing3);
> >  
> >  	return 0;
> >  
> 
> 




More information about the dri-devel mailing list