[PATCH v7 7/9] drm/mediatek: add dsi transfer function

[YT Shen]

Hi CK,

On Tue, 2016-09-13 at 17:25 +0800, CK Hu wrote:
> Hi, YT:
> 
> On Mon, 2016-09-12 at 18:16 +0800, YT Shen wrote:
> > Hi CK,
> > 
> > On Wed, 2016-09-07 at 10:33 +0800, CK Hu wrote:
> > > Hi, YT:
> > > 
> > > On Fri, 2016-09-02 at 19:24 +0800, YT Shen wrote:
> > > > From: shaoming chen <shaoming.chen at mediatek.com>
> > > > 
> > > > add dsi read/write commands for transfer function
> > > > 
> > > > Signed-off-by: shaoming chen <shaoming.chen at mediatek.com>
> > > > ---
> > > >  drivers/gpu/drm/mediatek/mtk_dsi.c | 188 +++++++++++++++++++++++++++++++++++++
> > > >  1 file changed, 188 insertions(+)
> > > > 
> > > 
> > > [snip...]
> > > 
> > > >  
> > > > +static void mtk_dsi_irq_data_clear(struct mtk_dsi *dsi, u32 irq_bit)
> > > > +{
> > > > +	dsi->irq_data &= ~irq_bit;
> > > > +}
> > > > +
> > > 
> > > [snip...]
> > > 
> > > > +
> > > > +static s32 mtk_dsi_wait_for_irq_done(struct mtk_dsi *dsi, u32 irq_flag,
> > > > +				     unsigned int timeout)
> > > > +{
> > > > +	s32 ret = 0;
> > > > +	unsigned long jiffies = msecs_to_jiffies(timeout);
> > > > +
> > > > +	ret = wait_event_interruptible_timeout(_dsi_irq_wait_queue,
> > > > +					       dsi->irq_data & irq_flag,
> > > > +					       jiffies);
> > > > +	if (ret == 0) {
> > > > +		dev_info(dsi->dev, "Wait DSI IRQ(0x%08x) Timeout\n", irq_flag);
> > > > +
> > > > +		mtk_dsi_enable(dsi);
> > > > +		mtk_dsi_reset_engine(dsi);
> > > > +	}
> > > > +
> > > > +	return ret;
> > > > +}
> > > 
> > > I think mtk_dsi_irq_data_clear() and mtk_dsi_wait_for_irq_done() should
> > > be moved to the 6th patch [1] of this series because these two functions
> > > deal the irq control.
> > We will move mtk_dsi_irq_data_clear() to patch "drm/mediatek: add dsi
> > interrupt control" and put mtk_dsi_wait_for_irq_done() here, because it
> > is used in the transfer function.
> 
> mtk_dsi_irq_data_clear() is also only used in transfer function now. I
> think both function could be used for other application rather than
> transfer function, so these two function are general function for irq
> control.
We will rollback the changes here.  Move mtk_dsi_irq_data_clear() to
original place.

Add new functions could be used in the future will have problems.
warning: 'mtk_dsi_wait_for_irq_done' defined but not used
[-Wunused-function]
 static s32 mtk_dsi_wait_for_irq_done(struct mtk_dsi *dsi, u32 irq_flag,
warning: 'mtk_dsi_irq_data_clear' defined but not used
[-Wunused-function]
 static void mtk_dsi_irq_data_clear(struct mtk_dsi *dsi, u32 irq_bit)

> Regards,
> CK
> 
> > 
> > Regards,
> > yt.shen
> > > 
> > > 
> > > [1] https://patchwork.kernel.org/patch/9310819/
> > > 
> > > 
> > > Regards,
> > > CK
> > > 
> > 
> > 
> 
>