[PATCH 2nd RESEND v2 1/3] video: add header file for Mobile High-Definition Link (MHL) interface
Andrzej Hajda
a.hajda at samsung.com
Wed Sep 14 08:33:45 UTC 2016
This header adds definitions specific to MHL protocol.
Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
---
include/linux/mhl.h | 292 ++++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 292 insertions(+)
create mode 100644 include/linux/mhl.h
diff --git a/include/linux/mhl.h b/include/linux/mhl.h
new file mode 100644
index 0000000..6917508
--- /dev/null
+++ b/include/linux/mhl.h
@@ -0,0 +1,292 @@
+/*
+ * Defines for Mobile High-Definition Link (MHL) interface
+ *
+ * Copyright (C) 2015, Samsung Electronics, Co., Ltd.
+ * Andrzej Hajda <a.hajda at samsung.com>
+ *
+ * Based on MHL driver for Android devices.
+ * Copyright (C) 2013-2014 Silicon Image, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef LINUX_MHL_H
+#define LINUX_MHL_H
+
+/* Device Capabilities Registers */
+enum {
+ MHL_DCAP_DEV_STATE,
+ MHL_DCAP_MHL_VERSION,
+ MHL_DCAP_CAT,
+ MHL_DCAP_ADOPTER_ID_H,
+ MHL_DCAP_ADOPTER_ID_L,
+ MHL_DCAP_VID_LINK_MODE,
+ MHL_DCAP_AUD_LINK_MODE,
+ MHL_DCAP_VIDEO_TYPE,
+ MHL_DCAP_LOG_DEV_MAP,
+ MHL_DCAP_BANDWIDTH,
+ MHL_DCAP_FEATURE_FLAG,
+ MHL_DCAP_DEVICE_ID_H,
+ MHL_DCAP_DEVICE_ID_L,
+ MHL_DCAP_SCRATCHPAD_SIZE,
+ MHL_DCAP_INT_STAT_SIZE,
+ MHL_DCAP_RESERVED,
+ MHL_DCAP_SIZE
+};
+
+#define MHL_DCAP_CAT_SINK 0x01
+#define MHL_DCAP_CAT_SOURCE 0x02
+#define MHL_DCAP_CAT_POWER 0x10
+#define MHL_DCAP_CAT_PLIM(x) ((x) << 5)
+
+#define MHL_DCAP_VID_LINK_RGB444 0x01
+#define MHL_DCAP_VID_LINK_YCBCR444 0x02
+#define MHL_DCAP_VID_LINK_YCBCR422 0x04
+#define MHL_DCAP_VID_LINK_PPIXEL 0x08
+#define MHL_DCAP_VID_LINK_ISLANDS 0x10
+#define MHL_DCAP_VID_LINK_VGA 0x20
+#define MHL_DCAP_VID_LINK_16BPP 0x40
+
+#define MHL_DCAP_AUD_LINK_2CH 0x01
+#define MHL_DCAP_AUD_LINK_8CH 0x02
+
+#define MHL_DCAP_VT_GRAPHICS 0x00
+#define MHL_DCAP_VT_PHOTO 0x02
+#define MHL_DCAP_VT_CINEMA 0x04
+#define MHL_DCAP_VT_GAMES 0x08
+#define MHL_DCAP_SUPP_VT 0x80
+
+#define MHL_DCAP_LD_DISPLAY 0x01
+#define MHL_DCAP_LD_VIDEO 0x02
+#define MHL_DCAP_LD_AUDIO 0x04
+#define MHL_DCAP_LD_MEDIA 0x08
+#define MHL_DCAP_LD_TUNER 0x10
+#define MHL_DCAP_LD_RECORD 0x20
+#define MHL_DCAP_LD_SPEAKER 0x40
+#define MHL_DCAP_LD_GUI 0x80
+#define MHL_DCAP_LD_ALL 0xFF
+
+#define MHL_DCAP_FEATURE_RCP_SUPPORT 0x01
+#define MHL_DCAP_FEATURE_RAP_SUPPORT 0x02
+#define MHL_DCAP_FEATURE_SP_SUPPORT 0x04
+#define MHL_DCAP_FEATURE_UCP_SEND_SUPPOR 0x08
+#define MHL_DCAP_FEATURE_UCP_RECV_SUPPORT 0x10
+#define MHL_DCAP_FEATURE_RBP_SUPPORT 0x40
+
+/* Extended Device Capabilities Registers */
+enum {
+ MHL_XDC_ECBUS_SPEEDS,
+ MHL_XDC_TMDS_SPEEDS,
+ MHL_XDC_ECBUS_ROLES,
+ MHL_XDC_LOG_DEV_MAPX,
+ MHL_XDC_SIZE
+};
+
+#define MHL_XDC_ECBUS_S_075 0x01
+#define MHL_XDC_ECBUS_S_8BIT 0x02
+#define MHL_XDC_ECBUS_S_12BIT 0x04
+#define MHL_XDC_ECBUS_D_150 0x10
+#define MHL_XDC_ECBUS_D_8BIT 0x20
+
+#define MHL_XDC_TMDS_000 0x00
+#define MHL_XDC_TMDS_150 0x01
+#define MHL_XDC_TMDS_300 0x02
+#define MHL_XDC_TMDS_600 0x04
+
+/* MHL_XDC_ECBUS_ROLES flags */
+#define MHL_XDC_DEV_HOST 0x01
+#define MHL_XDC_DEV_DEVICE 0x02
+#define MHL_XDC_DEV_CHARGER 0x04
+#define MHL_XDC_HID_HOST 0x08
+#define MHL_XDC_HID_DEVICE 0x10
+
+/* MHL_XDC_LOG_DEV_MAPX flags */
+#define MHL_XDC_LD_PHONE 0x01
+
+/* Device Status Registers */
+enum {
+ MHL_DST_CONNECTED_RDY,
+ MHL_DST_LINK_MODE,
+ MHL_DST_VERSION,
+ MHL_DST_SIZE
+};
+
+/* Offset of DEVSTAT registers */
+#define MHL_DST_OFFSET 0x30
+#define MHL_DST_REG(name) (MHL_DST_OFFSET + MHL_DST_##name)
+
+#define MHL_DST_CONN_DCAP_RDY 0x01
+#define MHL_DST_CONN_XDEVCAPP_SUPP 0x02
+#define MHL_DST_CONN_POW_STAT 0x04
+#define MHL_DST_CONN_PLIM_STAT_MASK 0x38
+
+#define MHL_DST_LM_CLK_MODE_MASK 0x07
+#define MHL_DST_LM_CLK_MODE_PACKED_PIXEL 0x02
+#define MHL_DST_LM_CLK_MODE_NORMAL 0x03
+#define MHL_DST_LM_PATH_EN_MASK 0x08
+#define MHL_DST_LM_PATH_ENABLED 0x08
+#define MHL_DST_LM_PATH_DISABLED 0x00
+#define MHL_DST_LM_MUTED_MASK 0x10
+
+/* Extended Device Status Registers */
+enum {
+ MHL_XDS_CURR_ECBUS_MODE,
+ MHL_XDS_AVLINK_MODE_STATUS,
+ MHL_XDS_AVLINK_MODE_CONTROL,
+ MHL_XDS_MULTI_SINK_STATUS,
+ MHL_XDS_SIZE
+};
+
+/* Offset of XDEVSTAT registers */
+#define MHL_XDS_OFFSET 0x90
+#define MHL_XDS_REG(name) (MHL_XDS_OFFSET + MHL_XDS_##name)
+
+/* MHL_XDS_REG_CURR_ECBUS_MODE flags */
+#define MHL_XDS_SLOT_MODE_8BIT 0x00
+#define MHL_XDS_SLOT_MODE_6BIT 0x01
+#define MHL_XDS_ECBUS_S 0x04
+#define MHL_XDS_ECBUS_D 0x08
+
+#define MHL_XDS_LINK_CLOCK_75MHZ 0x00
+#define MHL_XDS_LINK_CLOCK_150MHZ 0x10
+#define MHL_XDS_LINK_CLOCK_300MHZ 0x20
+#define MHL_XDS_LINK_CLOCK_600MHZ 0x30
+
+#define MHL_XDS_LINK_STATUS_NO_SIGNAL 0x00
+#define MHL_XDS_LINK_STATUS_CRU_LOCKED 0x01
+#define MHL_XDS_LINK_STATUS_TMDS_NORMAL 0x02
+#define MHL_XDS_LINK_STATUS_TMDS_RESERVED 0x03
+
+#define MHL_XDS_LINK_RATE_1_5_GBPS 0x00
+#define MHL_XDS_LINK_RATE_3_0_GBPS 0x01
+#define MHL_XDS_LINK_RATE_6_0_GBPS 0x02
+#define MHL_XDS_ATT_CAPABLE 0x08
+
+#define MHL_XDS_SINK_STATUS_1_HPD_LOW 0x00
+#define MHL_XDS_SINK_STATUS_1_HPD_HIGH 0x01
+#define MHL_XDS_SINK_STATUS_2_HPD_LOW 0x00
+#define MHL_XDS_SINK_STATUS_2_HPD_HIGH 0x04
+#define MHL_XDS_SINK_STATUS_3_HPD_LOW 0x00
+#define MHL_XDS_SINK_STATUS_3_HPD_HIGH 0x10
+#define MHL_XDS_SINK_STATUS_4_HPD_LOW 0x00
+#define MHL_XDS_SINK_STATUS_4_HPD_HIGH 0x40
+
+/* Interrupt Registers */
+enum {
+ MHL_INT_RCHANGE,
+ MHL_INT_DCHANGE,
+ MHL_INT_SIZE
+};
+
+/* Offset of DEVSTAT registers */
+#define MHL_INT_OFFSET 0x20
+#define MHL_INT_REG(name) (MHL_INT_OFFSET + MHL_INT_##name)
+
+#define MHL_INT_RC_DCAP_CHG 0x01
+#define MHL_INT_RC_DSCR_CHG 0x02
+#define MHL_INT_RC_REQ_WRT 0x04
+#define MHL_INT_RC_GRT_WRT 0x08
+#define MHL_INT_RC_3D_REQ 0x10
+#define MHL_INT_RC_FEAT_REQ 0x20
+#define MHL_INT_RC_FEAT_COMPLETE 0x40
+
+#define MHL_INT_DC_EDID_CHG 0x02
+
+enum {
+
+ MHL_ACK = 0x33, /* Command or Data byte acknowledge */
+ MHL_NACK = 0x34, /* Command or Data byte not acknowledge */
+ MHL_ABORT = 0x35, /* Transaction abort */
+ MHL_WRITE_STAT = 0xe0, /* Write one status register */
+ MHL_SET_INT = 0x60, /* Write one interrupt register */
+ MHL_READ_DEVCAP_REG = 0x61, /* Read one register */
+ MHL_GET_STATE = 0x62, /* Read CBUS revision level from follower */
+ MHL_GET_VENDOR_ID = 0x63, /* Read vendor ID value from follower */
+ MHL_SET_HPD = 0x64, /* Set Hot Plug Detect in follower */
+ MHL_CLR_HPD = 0x65, /* Clear Hot Plug Detect in follower */
+ MHL_SET_CAP_ID = 0x66, /* Set Capture ID for downstream device */
+ MHL_GET_CAP_ID = 0x67, /* Get Capture ID from downstream device */
+ MHL_MSC_MSG = 0x68, /* VS command to send RCP sub-commands */
+ MHL_GET_SC1_ERRORCODE = 0x69, /* Get Vendor-Specific error code */
+ MHL_GET_DDC_ERRORCODE = 0x6A, /* Get DDC channel command error code */
+ MHL_GET_MSC_ERRORCODE = 0x6B, /* Get MSC command error code */
+ MHL_WRITE_BURST = 0x6C, /* Write 1-16 bytes to responder's scratchpad */
+ MHL_GET_SC3_ERRORCODE = 0x6D, /* Get channel 3 command error code */
+ MHL_WRITE_XSTAT = 0x70, /* Write one extended status register */
+ MHL_READ_XDEVCAP_REG = 0x71, /* Read one extended devcap register */
+ /* let the rest of these float, they are software specific */
+ MHL_READ_EDID_BLOCK,
+ MHL_SEND_3D_REQ_OR_FEAT_REQ,
+ MHL_READ_DEVCAP,
+ MHL_READ_XDEVCAP
+};
+
+/* MSC message types */
+enum {
+ MHL_MSC_MSG_RCP = 0x10, /* RCP sub-command */
+ MHL_MSC_MSG_RCPK = 0x11, /* RCP Acknowledge sub-command */
+ MHL_MSC_MSG_RCPE = 0x12, /* RCP Error sub-command */
+ MHL_MSC_MSG_RAP = 0x20, /* Mode Change Warning sub-command */
+ MHL_MSC_MSG_RAPK = 0x21, /* MCW Acknowledge sub-command */
+ MHL_MSC_MSG_RBP = 0x22, /* Remote Button Protocol sub-command */
+ MHL_MSC_MSG_RBPK = 0x23, /* RBP Acknowledge sub-command */
+ MHL_MSC_MSG_RBPE = 0x24, /* RBP Error sub-command */
+ MHL_MSC_MSG_UCP = 0x30, /* UCP sub-command */
+ MHL_MSC_MSG_UCPK = 0x31, /* UCP Acknowledge sub-command */
+ MHL_MSC_MSG_UCPE = 0x32, /* UCP Error sub-command */
+ MHL_MSC_MSG_RUSB = 0x40, /* Request USB host role */
+ MHL_MSC_MSG_RUSBK = 0x41, /* Acknowledge request for USB host role */
+ MHL_MSC_MSG_RHID = 0x42, /* Request HID host role */
+ MHL_MSC_MSG_RHIDK = 0x43, /* Acknowledge request for HID host role */
+ MHL_MSC_MSG_ATT = 0x50, /* Request attention sub-command */
+ MHL_MSC_MSG_ATTK = 0x51, /* ATT Acknowledge sub-command */
+ MHL_MSC_MSG_BIST_TRIGGER = 0x60,
+ MHL_MSC_MSG_BIST_REQUEST_STAT = 0x61,
+ MHL_MSC_MSG_BIST_READY = 0x62,
+ MHL_MSC_MSG_BIST_STOP = 0x63,
+};
+
+/* RAP action codes */
+#define MHL_RAP_POLL 0x00 /* Just do an ack */
+#define MHL_RAP_CONTENT_ON 0x10 /* Turn content stream ON */
+#define MHL_RAP_CONTENT_OFF 0x11 /* Turn content stream OFF */
+#define MHL_RAP_CBUS_MODE_DOWN 0x20
+#define MHL_RAP_CBUS_MODE_UP 0x21
+
+/* RAPK status codes */
+#define MHL_RAPK_NO_ERR 0x00 /* RAP action recognized & supported */
+#define MHL_RAPK_UNRECOGNIZED 0x01 /* Unknown RAP action code received */
+#define MHL_RAPK_UNSUPPORTED 0x02 /* Rcvd RAP action code not supported */
+#define MHL_RAPK_BUSY 0x03 /* Responder too busy to respond */
+
+/*
+ * Error status codes for RCPE messages
+ */
+/* No error. (Not allowed in RCPE messages) */
+#define MHL_RCPE_STATUS_NO_ERROR 0x00
+/* Unsupported/unrecognized key code */
+#define MHL_RCPE_STATUS_INEFFECTIVE_KEY_CODE 0x01
+/* Responder busy. Initiator may retry message */
+#define MHL_RCPE_STATUS_BUSY 0x02
+
+/*
+ * Error status codes for RBPE messages
+ */
+/* No error. (Not allowed in RBPE messages) */
+#define MHL_RBPE_STATUS_NO_ERROR 0x00
+/* Unsupported/unrecognized button code */
+#define MHL_RBPE_STATUS_INEFFECTIVE_BUTTON_CODE 0x01
+/* Responder busy. Initiator may retry message */
+#define MHL_RBPE_STATUS_BUSY 0x02
+
+/*
+ * Error status codes for UCPE messages
+ */
+/* No error. (Not allowed in UCPE messages) */
+#define MHL_UCPE_STATUS_NO_ERROR 0x00
+/* Unsupported/unrecognized key code */
+#define MHL_UCPE_STATUS_INEFFECTIVE_KEY_CODE 0x01
+
+#endif /* LINUX_MHL_H */
--
1.9.1
More information about the dri-devel
mailing list