[RFC PATCH xserver] modesetting: re-set the crtc's mode when link-status goes BAD

Manasi Navare manasi.d.navare at intel.com
Mon Apr 3 06:25:42 UTC 2017


On Sun, Apr 02, 2017 at 07:21:09PM -0700, Eric Anholt wrote:
> Daniel Vetter <daniel at ffwll.ch> writes:
> 
> > On Fri, Mar 31, 2017 at 05:22:09PM -0700, Eric Anholt wrote:
> >> Manasi Navare <manasi.d.navare at intel.com> writes:
> >> 
> >> > On Fri, Mar 31, 2017 at 01:08:41PM -0700, Eric Anholt wrote:
> >> >> Manasi Navare <manasi.d.navare at intel.com> writes:
> >> >> 
> >> >> > On Thu, Mar 30, 2017 at 05:37:55PM -0700, Eric Anholt wrote:
> >> >> >> Martin Peres <martin.peres at linux.intel.com> writes:
> >> >> >> 
> >> >> >> > On 26/01/17 14:37, Martin Peres wrote:
> >> >> >> >> Despite all the careful planing of the kernel, a link may become
> >> >> >> >> insufficient to handle the currently-set mode. At this point, the
> >> >> >> >> kernel should mark this particular configuration as being broken
> >> >> >> >> and potentially prune the mode before setting the offending connector's
> >> >> >> >> link-status to BAD and send the userspace a hotplug event. This may
> >> >> >> >> happen right after a modeset or later on.
> >> >> >> >>
> >> >> >> >> When available, we should use the link-status information to reset
> >> >> >> >> the wanted mode.
> >> >> >> >>
> >> >> >> >> Signed-off-by: Martin Peres <martin.peres at linux.intel.com>
> >> >> >> >
> >> >> >> > The relevant kernel patches have landed in drm-tip about a month ago.
> >> >> >> >
> >> >> >> > Eric, would you mind providing feedback on or merging this patch?
> >> >> >> 
> >> >> >> The later discussion has sounded like the kernel will (always) prune the
> >> >> >> mode when we re-query, meaning that it doesn't make any sense to try to
> >> >> >> re-set to the old mode.  Is this not the case?
> >> >> >
> >> >> >
> >> >> > No the kernel will simply send a hotplug with link status as bad
> >> >> > and then after that point its userspace driver's responsibility
> >> >> > to check if link status is BAD, retry the same mode and if it fails
> >> >> > then re probe.
> >> >> 
> >> >> So the kernel will sometimes allow the same mode to be re-set with the
> >> >> same bpp?
> >> >
> >> > So when userspace driver re-sets the same mode, the kernel will call the
> >> > mode valid function where it will see it can allow the sam mode perhaps
> >> > at a lower bpp now since the link parameters are lowered.
> >> > So the mode which failed at 30 bpp, might still work at 18bpp and is
> >> > better going to a lower resolution.
> >> 
> >> The question was whether the kernel will ever allow the same mode at the
> >> same bpp, since that's what this patch tries to do.
> >
> > Yes, this can happen. Doing a full modeset with recomputing clocks and
> > everything behind userspace's back might not be something the kernel
> > driver can pull of with a reasonable amount of effort, hence why we punt
> > to userspace. The interface spec makes this a CAN, not WILL, to allow less
> > unreasonable hw to handle these cases directly in the kernel driver. E.g.
> > plain link-retraining is handled in i915.ko still.
> 
> So in that case you do need userspace to re-request the same mode at the
> same bpp?

So yes because when userspace requests the same mode at same bpp,
kernel will still call intel_dp->mod_valid which validates the mode
against 18bpp so if the requested mode can be displayed at the lowest of
18bpp, then the kernel will try to do the modeset for that mode at lower
bpp. What I am trying to say is irrespective of what bpp userspace requests,
kernel will check if it can display that at the lowest of 18bpp.

Regards
Manasi

> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel



More information about the dri-devel mailing list