[PATCH 2/2] ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board

[Krzysztof Kozlowski]

On Thu, Aug 03, 2017 at 09:45:23AM +0200, Maciej Purski wrote:
> This patch adds HDMI and Sil9234 MHL converter to Trats2 board.

Just "Add HDMI...", without this patch.

Except few minor nitpicks below, looks good. After fixing I will take it
once bindings got accepted.

> 
> Based on previous work by:
> Tomasz Stanislawski <t.stanislaws at samsung.com>
> 
> Signed-off-by: Maciej Purski <m.purski at samsung.com>
> ---
>  arch/arm/boot/dts/exynos4412-trats2.dts | 93 +++++++++++++++++++++++++++++++++
>  1 file changed, 93 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
> index 35e9b94..39940f6 100644
> --- a/arch/arm/boot/dts/exynos4412-trats2.dts
> +++ b/arch/arm/boot/dts/exynos4412-trats2.dts
> @@ -97,6 +97,16 @@
>  			gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>;
>  			enable-active-high;
>  		};
> +
> +		vsil: voltage-regulator-vsil {
> +			compatible = "regulator-fixed";
> +			regulator-name = "HDMI_5V";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +			vin-supply = <&buck7_reg>;

I think the supply is V_BAT, not buck7.

> +		};
>  	};
>  
>  	gpio-keys {
> @@ -229,6 +239,34 @@
>  		};
>  	};
>  
> +	i2c-mhl {
> +		compatible = "i2c-gpio";
> +		gpios = <&gpf0 4 GPIO_ACTIVE_HIGH &gpf0 6 GPIO_ACTIVE_HIGH>;
> +		i2c-gpio,delay-us = <100>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pinctrl-0 = <&i2c_mhl_bus>;
> +		pinctrl-names = "default";
> +		status = "okay";
> +
> +		sii9234: sii9234 at 39 {

The name of node should be rather generic (ePAPR: "The name of a node
should be somewhat generic, reflecting the function of the device and
not its precise programming model").

So maybe "sii9234: hdmi-bridge at 39"?

> +			compatible = "sil,sii9234";
> +			vcc-supply = <&vsil>;
> +			reset-gpios = <&gpf3 4 GPIO_ACTIVE_HIGH>;
> +			interrupt-parent = <&gpf3>;
> +			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
> +			reg = <0x39>;
> +
> +

One empty line instead of two.

> +			port {
> +				mhl_to_hdmi: endpoint {
> +					remote-endpoint = <&hdmi_to_mhl>;
> +				};
> +			};
> +		};
> +	};
> +
>  	camera: camera {
>  		pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
>  		pinctrl-names = "default";
> @@ -522,6 +560,31 @@
>  	status = "okay";
>  };
>  
> +&hdmi {
> +	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hdmi_hpd>;
> +	hdmi-en-supply = <&vsil>;
> +	vdd-supply = <&ldo3_reg>;
> +	vdd_osc-supply = <&ldo4_reg>;
> +	vdd_pll-supply = <&ldo3_reg>;
> +	ddc = <&i2c_5>;
> +	status = "okay";
> +
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port at 1 {
> +			reg = <1>;
> +			hdmi_to_mhl: endpoint {
> +				remote-endpoint = <&mhl_to_hdmi>;
> +			};
> +		};
> +	};
> +

Unnecessary empty line.

> +};
> +
>  &hsotg {
>  	vusb_d-supply = <&ldo15_reg>;
>  	vusb_a-supply = <&ldo12_reg>;
> @@ -600,6 +663,11 @@
>  	};
>  };
>  
> +
> +&i2c_5 {
> +	status = "okay";
> +};

Could you describe more what is on i2c_5 and i2c_8? Is it relevant to
this patch?

> +
>  &i2c_7 {
>  	samsung,i2c-sda-delay = <100>;
>  	samsung,i2c-slave-addr = <0x10>;
> @@ -894,12 +962,20 @@
>  	};
>  };
>  
> +&i2c_8 {
> +	status = "okay";
> +};
> +
>  &i2s0 {
>  	pinctrl-0 = <&i2s0_bus>;
>  	pinctrl-names = "default";
>  	status = "okay";
>  };
>  
> +&mixer {
> +	status = "okay";
> +};
> +
>  &mshc_0 {
>  	num-slots = <1>;
>  	broken-cd;
> @@ -926,6 +1002,18 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&sleep0>;
>  
> +	mhl_int: mhl-int {
> +		samsung,pins = "gpf3-5";
> +		samsung,pin-pud = <0>;

Please use defines from dt-bindings/pinctrl/samsung.h

> +	};
> +
> +	i2c_mhl_bus: i2c-mhl-bus {
> +		samsung,pins = "gpf0-4", "gpf0-6";
> +		samsung,pin-function = <2>;
> +		samsung,pin-pud = <1>;
> +		samsung,pin-drv = <0>;

The same.

Best regards,
Krzysztof