[PATCH 1/2] drm/bridge/sii8620: add external connector handle

[Laurent Pinchart]

Hi Marek,

On Thursday 17 Aug 2017 10:11:02 Rob Herring wrote:
> On Fri, Aug 11, 2017 at 02:49:35PM +0200, Marek Szyprowski wrote:
> > On 2017-08-11 11:40, Laurent Pinchart wrote:
> >> On Friday 11 Aug 2017 08:39:31 Marek Szyprowski wrote:
> >>> On 2017-08-10 15:39, Laurent Pinchart wrote:
> >>>> On Thursday 10 Aug 2017 15:25:29 Maciej Purski wrote:
> >>>>> The driver should be switched on if an external connector is
> >>>>> plugged and switched off if it is unplugged. Extcon is optional.
> >>>>> If it is not found, the driver stays in "always-on" mode.
> >>>>> 
> >>>>> Signed-off-by: Maciej Purski <m.purski at samsung.com>
> >>>>> ---
> >>>>> 
> >>>>> .../bindings/display/bridge/sil-sii8620.txt        |  4 ++
> >>>>> drivers/gpu/drm/bridge/sil-sii8620.c               | 83 ++++++++++++-
> >>>>> 2 files changed, 85 insertions(+), 2 deletions(-)
> >>>>> 
> >>>>> diff --git
> >>>>> a/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt
> >>>>> b/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt
> >>>>> index
> >>>>> 9409d9c..1f230bf 100644
> >>>>> --- a/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt
> >>>>> +++ b/Documentation/devicetree/bindings/display/bridge/sil-sii8620.txt 
> >>>>> @@ -10,6 +10,9 @@ Required properties:
> >>>>>    	- clocks, clock-names: specification and name of "xtal" clock
> >>>>>    	- video interfaces: Device node can contain video interface
> >>>>>    	  port node for HDMI encoder according to [1].
> >>>>> 
> >>>>> +Optional properties:
> >>>>> +	- extcon: phandle to external connector for MHL cable changes
> >>>>> +		  detection
> >>>> 
> >>>> The sii8620 DT node should model its connection to the MHL connector
> >>>> using OF graph, connecting a port to the MHL connector DT node through
> >>>> endpoints. I believe the extcon property should then be added to the
> >>>> MHL connector DT node, not the bridge.
> >>> 
> >>> I don't get this. Generic extcon bindings doesn't define connector DT
> >>> node, so I don't see how could we use endpoint DT approach here. Could
> >>> you give the example?
> >> 
> >> Sure, here you are.
> >> 
> >> &hsi2c_7 {
> >> 	...
> >>          sii8620 at 39 {
> >>                  reg = <0x39>;
> >>                  compatible = "sil,sii8620";
> >>                  cvcc10-supply = <&ldo36_reg>;
> >>                  iovcc18-supply = <&ldo34_reg>;
> >>                  interrupt-parent = <&gpf0>;
> >>                  interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
> >>                  reset-gpios = <&gpv7 0 GPIO_ACTIVE_LOW>;
> >>                  clocks = <&pmu_system_controller 0>;
> >>                  clock-names = "xtal";
> >> 		
> >> 		ports {
> >> 			#address-cells = <1>;
> >> 			#size-cells = <0>;
> >> 			
> >> 	                port at 0 {
> >> 				reg = <0>;
> >>          	                mhl_to_hdmi: endpoint {
> >>                  	                remote-endpoint = <&hdmi_to_mhl>;
> >> 	                        };
> >>          	        };
> >> 	                port at 1 {
> >> 				reg = <1>;
> >>          	                mhl_bridge_out: endpoint {
> >>                  	                remote-endpoint = <&mhl_connector_in>;
> >> 	                        };
> >>          	        };
> >> 		};
> >>          };
> >> };
> >> 
> >> / {
> >> 	mhl-connector {
> >> 		compatible = "mhl-connector";
> >> 		extcon = <&muic>;
> >> 		
> >> 	        port {
> >>          	        mhl_connector_in: endpoint {
> >>                  	        remote-endpoint = <&mhl_bridge_out>;
> >> 	                };
> >>          	};
> >> 	};
> >> };
> >> 
> >> Note that there's currently no DT binding for MHL connectors. One needs
> >> to be developed, the HDMI connector DT binding can be used as a source
> >> of inspiration.
> > 
> > Ah, I see. I wasn't aware that display subsystem has bindings even for the
> > connectors. Other types of connectors already used together with extcon in
> > device tree (like usb and chargers) don't have dedicated bindings.
> 
> I NAK any extcon binding additions because it is poorly designed, so
> don't use extcon. It is full of Linuxisms and needs work. USB
> connectors need to be described like what we have for display related
> connectors especially since they are merging.
> 
> > Do we need to add hdmi-connectors to all existing boards that have HDMI
> > module?
> 
> Ideally, yes.

I agree. In practice "details" such as backward compatibility need to be taken 
into account, but it's a good practice to update the mainline device tree 
sources to the recommended bindings.

-- 
Regards,

Laurent Pinchart