[Intel-gfx] [PATCH 9/9] drm/i915: Add render decompression support
Paulo Zanoni
paulo.r.zanoni at intel.com
Wed Jan 4 19:14:04 UTC 2017
Em Qua, 2017-01-04 às 20:42 +0200, ville.syrjala at linux.intel.com
escreveu:
> From: Ville Syrjälä <ville.syrjala at linux.intel.com>
>
> SKL+ display engine can scan out certain kinds of compressed surfaces
> produced by the render engine. This involved telling the display
> engine
> the location of the color control surfae (CCS) which describes
> which parts of the main surface are compressed and which are not. The
> location of CCS is provided by userspace as just another plane with
> its
> own offset.
>
> Add the required stuff to validate the user provided AUX plane
> metadata
> and convert the user provided linear offset into something the
> hardware
> can consume.
>
> Due to hardware limitations we require that the main surface and
> the AUX surface (CCS) be part of the same bo. The hardware also
> makes life hard by not allowing you to provide separate x/y offsets
> for the main and AUX surfaces (excpet with NV12), so finding suitable
> offsets for both requires a bit of work. Assuming we still want keep
> playing tricks with the offsets. I've just gone with a dumb "search
> backward for suitable offsets" approach, which is far from optimal,
> but it works.
>
> Also not all planes will be capable of scanning out compressed
> surfaces,
> and eg. 90/270 degree rotation is not supported in combination with
> decompression either.
>
> This patch may contain work from at least the following people:
> * Vandana Kannan <vandana.kannan at intel.com>
> * Daniel Vetter <daniel at ffwll.ch>
> * Ben Widawsky <ben at bwidawsk.net>
As I mentioned to Ben in the other email, there are some points of
BSpec that say "if render decompression is enabled, to this", which we
largely ignored so far. I hope they are all marked as workarounds. From
a quick look, it looks like we need at least Display WAs #0390, #0531
and #1125, and maybe some other non-display WAs (please take a look at
the BSpec list). I'll assume they were not implemented yet since I
don't see WA comments on the patches. I think we need them, otherwise
we may introduce more SKL flickering problems.
Thanks,
Paulo
>
> Cc: Vandana Kannan <vandana.kannan at intel.com>
> Cc: Daniel Vetter <daniel at ffwll.ch>
> Cc: Ben Widawsky <ben at bwidawsk.net>
> Cc: Jason Ekstrand <jason at jlekstrand.net>
> Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> ---
> drivers/gpu/drm/i915/i915_reg.h | 22 ++++
> drivers/gpu/drm/i915/intel_display.c | 219
> +++++++++++++++++++++++++++++++++--
> drivers/gpu/drm/i915/intel_pm.c | 8 +-
> drivers/gpu/drm/i915/intel_sprite.c | 5 +
> 4 files changed, 240 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/i915_reg.h
> b/drivers/gpu/drm/i915/i915_reg.h
> index 00970aa77afa..05e18e742776 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -6209,6 +6209,28 @@ enum {
> _ID(id, _PS_ECC_STAT_1A,
> _PS_ECC_STAT_2A), \
> _ID(id, _PS_ECC_STAT_1B, _PS_ECC_STAT_2B))
>
> +#define PLANE_AUX_DIST_1_A 0x701c0
> +#define PLANE_AUX_DIST_2_A 0x702c0
> +#define PLANE_AUX_DIST_1_B 0x711c0
> +#define PLANE_AUX_DIST_2_B 0x712c0
> +#define _PLANE_AUX_DIST_1(pipe) \
> + _PIPE(pipe, PLANE_AUX_DIST_1_A,
> PLANE_AUX_DIST_1_B)
> +#define _PLANE_AUX_DIST_2(pipe) \
> + _PIPE(pipe, PLANE_AUX_DIST_2_A,
> PLANE_AUX_DIST_2_B)
> +#define PLANE_AUX_DIST(pipe, plane) \
> + _MMIO_PLANE(plane, _PLANE_AUX_DIST_1(pipe),
> _PLANE_AUX_DIST_2(pipe))
> +
> +#define PLANE_AUX_OFFSET_1_A 0x701c4
> +#define PLANE_AUX_OFFSET_2_A 0x702c4
> +#define PLANE_AUX_OFFSET_1_B 0x711c4
> +#define PLANE_AUX_OFFSET_2_B 0x712c4
> +#define _PLANE_AUX_OFFSET_1(pipe) \
> + _PIPE(pipe, PLANE_AUX_OFFSET_1_A,
> PLANE_AUX_OFFSET_1_B)
> +#define _PLANE_AUX_OFFSET_2(pipe) \
> + _PIPE(pipe, PLANE_AUX_OFFSET_2_A,
> PLANE_AUX_OFFSET_2_B)
> +#define PLANE_AUX_OFFSET(pipe, plane) \
> + _MMIO_PLANE(plane, _PLANE_AUX_OFFSET_1(pipe),
> _PLANE_AUX_OFFSET_2(pipe))
> +
> /* legacy palette */
> #define _LGC_PALETTE_A 0x4a000
> #define _LGC_PALETTE_B 0x4a800
> diff --git a/drivers/gpu/drm/i915/intel_display.c
> b/drivers/gpu/drm/i915/intel_display.c
> index 38de9df0ec60..b547332eeda1 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -2064,11 +2064,19 @@ intel_tile_width_bytes(const struct
> drm_framebuffer *fb, int plane)
> return 128;
> else
> return 512;
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> + if (plane == 1)
> + return 64;
> + /* fall through */
> case I915_FORMAT_MOD_Y_TILED:
> if (IS_GEN2(dev_priv) ||
> HAS_128_BYTE_Y_TILING(dev_priv))
> return 128;
> else
> return 512;
> + case I915_FORMAT_MOD_Yf_TILED_CCS:
> + if (plane == 1)
> + return 64;
> + /* fall through */
> case I915_FORMAT_MOD_Yf_TILED:
> /*
> * Bspec seems to suggest that the Yf tile width
> would
> @@ -2156,7 +2164,7 @@ static unsigned int intel_surf_alignment(const
> struct drm_framebuffer *fb,
> struct drm_i915_private *dev_priv = to_i915(fb->dev);
>
> /* AUX_DIST needs only 4K alignment */
> - if (fb->format->format == DRM_FORMAT_NV12 && plane == 1)
> + if (plane == 1)
> return 4096;
>
> switch (fb->modifier) {
> @@ -2166,6 +2174,8 @@ static unsigned int intel_surf_alignment(const
> struct drm_framebuffer *fb,
> if (INTEL_GEN(dev_priv) >= 9)
> return 256 * 1024;
> return 0;
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> + case I915_FORMAT_MOD_Yf_TILED_CCS:
> case I915_FORMAT_MOD_Y_TILED:
> case I915_FORMAT_MOD_Yf_TILED:
> return 1 * 1024 * 1024;
> @@ -2472,6 +2482,7 @@ static unsigned int
> intel_fb_modifier_to_tiling(uint64_t fb_modifier)
> case I915_FORMAT_MOD_X_TILED:
> return I915_TILING_X;
> case I915_FORMAT_MOD_Y_TILED:
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> return I915_TILING_Y;
> default:
> return I915_TILING_NONE;
> @@ -2536,6 +2547,35 @@ intel_fill_fb_info(struct drm_i915_private
> *dev_priv,
>
> intel_fb_offset_to_xy(&x, &y, fb, i);
>
> + if ((fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS)
> && i == 1) {
> + int main_x, main_y;
> + int ccs_x, ccs_y;
> +
> + /*
> + * Each byte of CCS corresponds to a 16x8
> area of the main surface, and
> + * each CCS tile is 64x64 bytes.
> + */
> + ccs_x = (x * 16) % (64 * 16);
> + ccs_y = (y * 8) % (64 * 8);
> + main_x = intel_fb->normal[0].x % (64 * 16);
> + main_y = intel_fb->normal[0].y % (64 * 8);
> +
> + /*
> + * CCS doesn't have its own x/y offset
> register, so the intra CCS tile
> + * x/y offsets must match between CCS and
> the main surface.
> + */
> + if (main_x != ccs_x || main_y != ccs_y) {
> + DRM_DEBUG_KMS("Bad CCS x/y (main
> %d,%d ccs %d,%d) full (main %d,%d ccs %d,%d)\n",
> + main_x, main_y,
> + ccs_x, ccs_y,
> + intel_fb->normal[0].x,
> + intel_fb->normal[0].y,
> + x, y);
> + return -EINVAL;
> + }
> + }
> +
> /*
> * The fence (if used) is aligned to the start of
> the object
> * so having the framebuffer wrap around across the
> edge of the
> @@ -2873,6 +2913,9 @@ static int skl_max_plane_width(const struct
> drm_framebuffer *fb, int plane,
> break;
> }
> break;
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> + case I915_FORMAT_MOD_Yf_TILED_CCS:
> + /* FIXME AUX plane? */
> case I915_FORMAT_MOD_Y_TILED:
> case I915_FORMAT_MOD_Yf_TILED:
> switch (cpp) {
> @@ -2895,6 +2938,42 @@ static int skl_max_plane_width(const struct
> drm_framebuffer *fb, int plane,
> return 2048;
> }
>
> +static bool skl_check_main_ccs_coordinates(struct intel_plane_state
> *plane_state,
> + int main_x, int main_y,
> u32 main_offset)
> +{
> + const struct drm_framebuffer *fb = plane_state->base.fb;
> + int aux_x = plane_state->aux.x;
> + int aux_y = plane_state->aux.y;
> + u32 aux_offset = plane_state->aux.offset;
> + u32 alignment = intel_surf_alignment(fb, 1);
> +
> + while (aux_offset >= main_offset && aux_y <= main_y) {
> + int x, y;
> +
> + if (aux_x == main_x && aux_y == main_y)
> + break;
> +
> + if (aux_offset == 0)
> + break;
> +
> + x = aux_x / 16;
> + y = aux_y / 8;
> + aux_offset = intel_adjust_tile_offset(&x, &y,
> plane_state, 1,
> + aux_offset,
> aux_offset - alignment);
> + aux_x = x * 16 + aux_x % 16;
> + aux_y = y * 8 + aux_y % 8;
> + }
> +
> + if (aux_x != main_x || aux_y != main_y)
> + return false;
> +
> + plane_state->aux.offset = aux_offset;
> + plane_state->aux.x = aux_x;
> + plane_state->aux.y = aux_y;
> +
> + return true;
> +}
> +
> static int skl_check_main_surface(struct intel_plane_state
> *plane_state)
> {
> const struct drm_framebuffer *fb = plane_state->base.fb;
> @@ -2937,7 +3016,7 @@ static int skl_check_main_surface(struct
> intel_plane_state *plane_state)
>
> while ((x + w) * cpp > fb->pitches[0]) {
> if (offset == 0) {
> - DRM_DEBUG_KMS("Unable to find
> suitable display surface offset\n");
> + DRM_DEBUG_KMS("Unable to find
> suitable display surface offset due to X-tiling\n");
> return -EINVAL;
> }
>
> @@ -2946,6 +3025,26 @@ static int skl_check_main_surface(struct
> intel_plane_state *plane_state)
> }
> }
>
> + /*
> + * CCS AUX surface doesn't have its own x/y offsets, we must
> make sure
> + * they match with the main surface x/y offsets.
> + */
> + if (fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS) {
> + while (!skl_check_main_ccs_coordinates(plane_state,
> x, y, offset)) {
> + if (offset == 0)
> + break;
> +
> + offset = intel_adjust_tile_offset(&x, &y,
> plane_state, 0,
> + offset,
> offset - alignment);
> + }
> +
> + if (x != plane_state->aux.x || y != plane_state-
> >aux.y) {
> + DRM_DEBUG_KMS("Unable to find suitable
> display surface offset due to CCS\n");
> + return -EINVAL;
> + }
> + }
> +
> plane_state->main.offset = offset;
> plane_state->main.x = x;
> plane_state->main.y = y;
> @@ -2982,6 +3081,53 @@ static int skl_check_nv12_aux_surface(struct
> intel_plane_state *plane_state)
> return 0;
> }
>
> +static int skl_check_ccs_aux_surface(struct intel_plane_state
> *plane_state)
> +{
> + struct intel_plane *plane = to_intel_plane(plane_state-
> >base.plane);
> + struct intel_crtc *crtc = to_intel_crtc(plane_state-
> >base.crtc);
> + int src_x = plane_state->base.src.x1 >> 16;
> + int src_y = plane_state->base.src.y1 >> 16;
> + int x = src_x / 16;
> + int y = src_y / 8;
> + u32 offset;
> +
> + switch (plane->id) {
> + case PLANE_PRIMARY:
> + case PLANE_SPRITE0:
> + break;
> + default:
> + DRM_DEBUG_KMS("RC support only on plane 1 and 2\n");
> + return -EINVAL;
> + }
> +
> + if (crtc->pipe == PIPE_C) {
> + DRM_DEBUG_KMS("No RC support on pipe C\n");
> + return -EINVAL;
> + }
> + /*
> + * TODO:
> + * 1. Disable stereo 3D when render decomp is enabled (bit
> 7:6)
> + * 2. Render decompression must not be used in VTd pass-
> through mode
> + * 3. Program hashing select CHICKEN_MISC1 bit 15
> + */
> +
> + if (plane_state->base.rotation &&
> + plane_state->base.rotation & ~(DRM_ROTATE_0 |
> DRM_ROTATE_180)) {
> + DRM_DEBUG_KMS("RC support only with 0/180 degree
> rotation %x\n",
> + plane_state->base.rotation);
> + return -EINVAL;
> + }
> +
> + intel_add_fb_offsets(&x, &y, plane_state, 1);
> + offset = intel_compute_tile_offset(&x, &y, plane_state, 1);
> +
> + plane_state->aux.offset = offset;
> + plane_state->aux.x = x * 16 + src_x % 16;
> + plane_state->aux.y = y * 8 + src_y % 8;
> +
> + return 0;
> +}
> +
> int skl_check_plane_surface(struct intel_plane_state *plane_state)
> {
> const struct drm_framebuffer *fb = plane_state->base.fb;
> @@ -3002,6 +3148,11 @@ int skl_check_plane_surface(struct
> intel_plane_state *plane_state)
> ret = skl_check_nv12_aux_surface(plane_state);
> if (ret)
> return ret;
> + } else if (fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS) {
> + ret = skl_check_ccs_aux_surface(plane_state);
> + if (ret)
> + return ret;
> } else {
> plane_state->aux.offset = ~0xfff;
> plane_state->aux.x = 0;
> @@ -3357,8 +3508,12 @@ u32 skl_plane_ctl_tiling(uint64_t fb_modifier)
> return PLANE_CTL_TILED_X;
> case I915_FORMAT_MOD_Y_TILED:
> return PLANE_CTL_TILED_Y;
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> + return PLANE_CTL_TILED_Y |
> PLANE_CTL_DECOMPRESSION_ENABLE;
> case I915_FORMAT_MOD_Yf_TILED:
> return PLANE_CTL_TILED_YF;
> + case I915_FORMAT_MOD_Yf_TILED_CCS:
> + return PLANE_CTL_TILED_YF |
> PLANE_CTL_DECOMPRESSION_ENABLE;
> default:
> MISSING_CASE(fb_modifier);
> }
> @@ -3401,6 +3556,7 @@ static void skylake_update_primary_plane(struct
> drm_plane *plane,
> u32 plane_ctl;
> unsigned int rotation = plane_state->base.rotation;
> u32 stride = skl_plane_stride(fb, 0, rotation);
> + u32 aux_stride = skl_plane_stride(fb, 1, rotation);
> u32 surf_addr = plane_state->main.offset;
> int scaler_id = plane_state->scaler_id;
> int src_x = plane_state->main.x;
> @@ -3436,6 +3592,10 @@ static void
> skylake_update_primary_plane(struct drm_plane *plane,
> I915_WRITE(PLANE_OFFSET(pipe, plane_id), (src_y << 16) |
> src_x);
> I915_WRITE(PLANE_STRIDE(pipe, plane_id), stride);
> I915_WRITE(PLANE_SIZE(pipe, plane_id), (src_h << 16) |
> src_w);
> + I915_WRITE(PLANE_AUX_DIST(pipe, plane_id),
> + (plane_state->aux.offset - surf_addr) |
> aux_stride);
> + I915_WRITE(PLANE_AUX_OFFSET(pipe, plane_id),
> + (plane_state->aux.y << 16) | plane_state->aux.x);
>
> if (scaler_id >= 0) {
> uint32_t ps_ctrl = 0;
> @@ -9807,10 +9967,16 @@ skylake_get_initial_plane_config(struct
> intel_crtc *crtc,
> fb->modifier = I915_FORMAT_MOD_X_TILED;
> break;
> case PLANE_CTL_TILED_Y:
> - fb->modifier = I915_FORMAT_MOD_Y_TILED;
> + if (val & PLANE_CTL_DECOMPRESSION_ENABLE)
> + fb->modifier = I915_FORMAT_MOD_Y_TILED_CCS;
> + else
> + fb->modifier = I915_FORMAT_MOD_Y_TILED;
> break;
> case PLANE_CTL_TILED_YF:
> - fb->modifier = I915_FORMAT_MOD_Yf_TILED;
> + if (val & PLANE_CTL_DECOMPRESSION_ENABLE)
> + fb->modifier = I915_FORMAT_MOD_Yf_TILED_CCS;
> + else
> + fb->modifier = I915_FORMAT_MOD_Yf_TILED;
> break;
> default:
> MISSING_CASE(tiling);
> @@ -12014,7 +12180,7 @@ static void skl_do_mmio_flip(struct
> intel_crtc *intel_crtc,
> u32 ctl, stride = skl_plane_stride(fb, 0, rotation);
>
> ctl = I915_READ(PLANE_CTL(pipe, 0));
> - ctl &= ~PLANE_CTL_TILED_MASK;
> + ctl &= ~(PLANE_CTL_TILED_MASK |
> PLANE_CTL_DECOMPRESSION_ENABLE);
> switch (fb->modifier) {
> case DRM_FORMAT_MOD_NONE:
> break;
> @@ -12024,9 +12190,15 @@ static void skl_do_mmio_flip(struct
> intel_crtc *intel_crtc,
> case I915_FORMAT_MOD_Y_TILED:
> ctl |= PLANE_CTL_TILED_Y;
> break;
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> + ctl |= PLANE_CTL_TILED_Y |
> PLANE_CTL_DECOMPRESSION_ENABLE;
> + break;
> case I915_FORMAT_MOD_Yf_TILED:
> ctl |= PLANE_CTL_TILED_YF;
> break;
> + case I915_FORMAT_MOD_Yf_TILED_CCS:
> + ctl |= PLANE_CTL_TILED_YF |
> PLANE_CTL_DECOMPRESSION_ENABLE;
> + break;
> default:
> MISSING_CASE(fb->modifier);
> }
> @@ -15926,8 +16098,8 @@ static int intel_framebuffer_init(struct
> drm_device *dev,
> {
> struct drm_i915_private *dev_priv = to_i915(dev);
> unsigned int tiling = i915_gem_object_get_tiling(obj);
> - int ret;
> - u32 pitch_limit, stride_alignment;
> + int ret, i;
> + u32 pitch_limit;
> struct drm_format_name_buf format_name;
>
> WARN_ON(!mutex_is_locked(&dev->struct_mutex));
> @@ -15953,6 +16125,19 @@ static int intel_framebuffer_init(struct
> drm_device *dev,
>
> /* Passed in modifier sanity checking. */
> switch (mode_cmd->modifier[0]) {
> + case I915_FORMAT_MOD_Y_TILED_CCS:
> + case I915_FORMAT_MOD_Yf_TILED_CCS:
> + switch (mode_cmd->pixel_format) {
> + case DRM_FORMAT_XBGR8888:
> + case DRM_FORMAT_ABGR8888:
> + case DRM_FORMAT_XRGB8888:
> + case DRM_FORMAT_ARGB8888:
> + break;
> + default:
> + DRM_DEBUG_KMS("RC supported only with
> RGB8888 formats\n");
> + return -EINVAL;
> + }
> + /* fall through */
> case I915_FORMAT_MOD_Y_TILED:
> case I915_FORMAT_MOD_Yf_TILED:
> if (INTEL_GEN(dev_priv) < 9) {
> @@ -16061,11 +16246,21 @@ static int intel_framebuffer_init(struct
> drm_device *dev,
>
> drm_helper_mode_fill_fb_struct(dev, &intel_fb->base,
> mode_cmd);
>
> - stride_alignment = intel_fb_stride_alignment(&intel_fb-
> >base, 0);
> - if (mode_cmd->pitches[0] & (stride_alignment - 1)) {
> - DRM_DEBUG_KMS("pitch (%d) must be at least %u byte
> aligned\n",
> - mode_cmd->pitches[0],
> stride_alignment);
> - return -EINVAL;
> + for (i = 0; i < intel_fb->base.format->num_planes; i++) {
> + u32 stride_alignment;
> +
> + if (mode_cmd->handles[i] != mode_cmd->handles[0]) {
> + DRM_DEBUG_KMS("bad plane %d handle\n", i);
> + return -EINVAL;
> + }
> +
> + stride_alignment =
> intel_fb_stride_alignment(&intel_fb->base, i);
> +
> + if (mode_cmd->pitches[i] & (stride_alignment - 1)) {
> + DRM_DEBUG_KMS("plane %d pitch (%d) must be
> at least %u byte aligned\n",
> + i, mode_cmd->pitches[i],
> stride_alignment);
> + return -EINVAL;
> + }
> }
>
> intel_fb->obj = obj;
> diff --git a/drivers/gpu/drm/i915/intel_pm.c
> b/drivers/gpu/drm/i915/intel_pm.c
> index 249623d45be0..add359022c96 100644
> --- a/drivers/gpu/drm/i915/intel_pm.c
> +++ b/drivers/gpu/drm/i915/intel_pm.c
> @@ -3314,7 +3314,9 @@ skl_ddb_min_alloc(const struct drm_plane_state
> *pstate,
>
> /* For Non Y-tile return 8-blocks */
> if (fb->modifier != I915_FORMAT_MOD_Y_TILED &&
> - fb->modifier != I915_FORMAT_MOD_Yf_TILED)
> + fb->modifier != I915_FORMAT_MOD_Yf_TILED &&
> + fb->modifier != I915_FORMAT_MOD_Y_TILED_CCS &&
> + fb->modifier != I915_FORMAT_MOD_Yf_TILED_CCS)
> return 8;
>
> src_w = drm_rect_width(&intel_pstate->base.src) >> 16;
> @@ -3590,7 +3592,9 @@ static int skl_compute_plane_wm(const struct
> drm_i915_private *dev_priv,
> }
>
> y_tiled = fb->modifier == I915_FORMAT_MOD_Y_TILED ||
> - fb->modifier == I915_FORMAT_MOD_Yf_TILED;
> + fb->modifier == I915_FORMAT_MOD_Yf_TILED ||
> + fb->modifier == I915_FORMAT_MOD_Y_TILED_CCS ||
> + fb->modifier == I915_FORMAT_MOD_Yf_TILED_CCS;
> x_tiled = fb->modifier == I915_FORMAT_MOD_X_TILED;
>
> /* Display WA #1141: kbl. */
> diff --git a/drivers/gpu/drm/i915/intel_sprite.c
> b/drivers/gpu/drm/i915/intel_sprite.c
> index 7031bc733d97..063a994815d0 100644
> --- a/drivers/gpu/drm/i915/intel_sprite.c
> +++ b/drivers/gpu/drm/i915/intel_sprite.c
> @@ -210,6 +210,7 @@ skl_update_plane(struct drm_plane *drm_plane,
> u32 surf_addr = plane_state->main.offset;
> unsigned int rotation = plane_state->base.rotation;
> u32 stride = skl_plane_stride(fb, 0, rotation);
> + u32 aux_stride = skl_plane_stride(fb, 1, rotation);
> int crtc_x = plane_state->base.dst.x1;
> int crtc_y = plane_state->base.dst.y1;
> uint32_t crtc_w = drm_rect_width(&plane_state->base.dst);
> @@ -248,6 +249,10 @@ skl_update_plane(struct drm_plane *drm_plane,
> I915_WRITE(PLANE_OFFSET(pipe, plane_id), (y << 16) | x);
> I915_WRITE(PLANE_STRIDE(pipe, plane_id), stride);
> I915_WRITE(PLANE_SIZE(pipe, plane_id), (src_h << 16) |
> src_w);
> + I915_WRITE(PLANE_AUX_DIST(pipe, plane_id),
> + (plane_state->aux.offset - surf_addr) |
> aux_stride);
> + I915_WRITE(PLANE_AUX_OFFSET(pipe, plane_id),
> + (plane_state->aux.y << 16) | plane_state->aux.x);
>
> /* program plane scaler */
> if (plane_state->scaler_id >= 0) {
More information about the dri-devel
mailing list