[PATCH v1 1/7] dt-bindings: display: add STM32 LTDC driver

Yannick FERTRE yannick.fertre at st.com
Thu Jan 19 16:16:01 UTC 2017


On 01/16/2017 09:30 PM, Laurent Pinchart wrote:
> Hi Yannick,
>
> Thank you for the patch.
>
> On Monday 16 Jan 2017 14:28:58 Yannick Fertre wrote:
>> Signed-off-by: Yannick Fertre <yannick.fertre at st.com>
>> ---
>>  .../devicetree/bindings/display/st,ltdc.txt        | 57 ++++++++++++++++++
>>  1 file changed, 57 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/display/st,ltdc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/display/st,ltdc.txt
>> b/Documentation/devicetree/bindings/display/st,ltdc.txt new file mode
>> 100644
>> index 0000000..20e89da
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/st,ltdc.txt
>> @@ -0,0 +1,57 @@
>> +* STMicroelectronics STM32 lcd-tft display controller
>> +
>> +- st-display-subsystem: Master device for DRM sub-components
>> +  This device must be the parent of all the sub-components and is
>> responsible
>> +  of bind them.
>
> Why do you need this ? At a quick glance the ltdc node should be enough.
Hi Laurent,
To prepare next device upstream of dsi, we need a master node 
"st-display-subsystem" and a sub node "st,ltdc". It's the same kind of 
node than st,stih4xx.
>
>> +  Required properties:
>> +  - compatible: "st,display-subsystem"
>> +  - ranges: to allow probing of subdevices
>> +
>> +- ltdc_host: lcd-tft display controller host
>> +  must be a sub-node of st-display-subsystem
>> +  Required properties:
>> +  - compatible: "st,ltdc"
>> +  - reg: Physical base address of the IP registers and length of memory
>> mapped region.
>> +  - clocks: from common clock binding: handle hardware IP needed clocks,
>> the
>> +    number of clocks may depend of the SoC type.
>> +    See ../clocks/clock-bindings.txt for details.
>> +  - clock-names: names of the clocks listed in clocks property in the same
>> +    order.
>
> You need to define the required/optional clocks with their names here. If they
> vary depending on the SoC, the DT bindings document need to list them for each
> SoC.
>
Ok, I'll push news bindings with pack V2.
>> +  - resets: resets to be used by the device
>> +    See ../reset/reset.txt for details.
>> +  - reset-names: names of the resets listed in resets property in the same
>> +    order.
>> +  Required nodes:
>> +    - Video port for RGB output.
>> +
>> +Example:
>> +
>> +/ {
>> +	...
>> +	soc {
>> +	...
>> +		st-display-subsystem {
>> +			compatible = "st,display-subsystem";
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +			dma-ranges;
>> +
>> +			ltdc_host: stm32-ltdc at 40016800 {
>> +				compatible = "st,ltdc";
>> +				reg = <0x40016800 0x200>;
>> +				interrupts = <88>, <89>;
>> +				resets = <&rcc 314>;
>> +				clocks = <&rcc 1 8>;
>> +				clock-names = "clk-lcd";
>> +				status = "disabled";
>> +
>> +				port {
>> +					ltdc_out_rgb: endpoint {
>> +					};
>> +				};
>> +			};
>> +		};
>> +	...
>> +	};
>> +};
>


More information about the dri-devel mailing list