[PATCH] drm: bridge: synopsys/dw-hdmi: Provide default configuration function for HDMI 2.0 PHY

[Zheng Yang]

Hi, Jose：

     The value of RK3399 reg HDMI_CONFIG2_ID is 0xf3.

     Using hdmi_phy_configure_dwc_hdmi_3d_tx() for hdmi 2.0 phy, we test 
all HDMI video mode(including 594MHz) and it woks good.

     And our customer has pass the HDMI CTS.

     If you send a patch with a general config function for HDMI 2.0 
phys, we  can test it on our platform.

福州瑞芯微电子股份有限公司   郑阳
Email: zhengyang at rock-chips.com

在 2017年06月22日 16:25, Mark yao 写道:
> Hi Jose
>
> Sorry miss your email and Sorry for the late reply
>
> I can sure that your patch works on our rk3399 platform.
>
> my internal kernel already has similar patch, using 
> hdmi_phy_configure_dwc_hdmi_3d_tx() for hdmi 2.0 phy,
> good works with many video modes (4k, 1080p, 720p etc.), I'm not 
> familiar with hdmi,  but hdmi display actually works for us.
>
> And, I had tried the 4.12-rc1 kernel with your patch, display works good.
>
> So:
> Tested-by: Mark Yao <mark.yao at rock-chips.com>
>
> On 2017年06月13日 22:11, Jose Abreu wrote:
>> Hi Laurent,
>>
>>
>> Sorry for the late reply!
>>
>>
>> On 10-06-2017 09:50, Laurent Pinchart wrote:
>>> Hi Jose,
>>>
>>> On Friday 09 Jun 2017 13:53:12 Jose Abreu wrote:
>>>> On 09-06-2017 12:04, Jose Abreu wrote:
>>>>> Currently HDMI 2.0 PHYs do not have a default configuration function.
>>>>>
>>>>> As these PHYs have the same register layout as the 3D PHYs we can
>>>>> safely use the default configuration function.
>>>> I may have been a little to fast arriving at this conclusion. I
>>>> mean most of the registers match but in the configuration
>>>> function there are registers that do not match. Did you actually
>>>> test this configuration function with an HDMI 2.0 phy? And did
>>>> you test with different video modes? From my experience the phy
>>>> may be wrongly configured and sometimes work anyway.
>>>>
>>>> Do please retest with as many video modes as you can and give me
>>>> your phy ID (read from controller config reg HDMI_CONFIG2_ID).
>>> The Renesas R-Car Gen3 HDMI PHY reports an DWC HDMI 2.0 TX PHY ID, 
>>> but has a
>>> configuration function (rcar_hdmi_phy_configure() in 
>>> drivers/gpu/drm/rcar-
>>> du/rcar_dw_hdmi.c) that doesn't match 
>>> hdmi_phy_configure_dwc_hdmi_3d_tx().
>>>  From the information I have been given the layout of the configuration
>>> registers haven't been changed by Renesas. I know we've briefly 
>>> discussed this
>>> in the past, but I'd appreciate if you could have a second look and 
>>> tell me
>>> what you think.
>> Yup, yours seems correct. Though at the time you submitted I
>> found it odd that only 3 registers needed to be written whilst
>> for HDMI 2.0 phys I have here 6 registers, but you said it is
>> working so I though your phy was different ...
>>
>> Even so, one thing I would like to know is what was the max
>> resolution you tested? I see you have clock values up to 297MHz,
>> so 4k at 30Hz? If I send a patch with a general config function for
>> HDMI 2.0 phys can you test it on your platform?
>>
>> Best regards,
>> Jose Miguel Abreu
>>
>>>>>   If, for some reason,
>>>>>
>>>>> the PHY is custom this change will not make any impact because
>>>>> in configuration function we prefer the pdata provided configuration
>>>>> function over the internal one.
>>>>>
>>>>> This patch is based on today's drm-misc-next branch.
>>>>>
>>>>> Signed-off-by: Jose Abreu <joabreu at synopsys.com>
>>>>> Cc: Kieran Bingham <kieran.bingham+renesas at ideasonboard.com>
>>>>> Cc: Laurent Pinchart <laurent.pinchart+renesas at ideasonboard.com>
>>>>> Cc: Archit Taneja <architt at codeaurora.org>
>>>>> Cc: Andrzej Hajda <a.hajda at samsung.com>
>>>>> Cc: Mark Yao <mark.yao at rock-chips.com>
>>>>> Cc: Carlos Palminha <palminha at synopsys.com>
>>>>> ---
>>>>>
>>>>>   drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 1 +
>>>>>   1 file changed, 1 insertion(+)
>>>>>
>>>>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>>>>> b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index ead1124..10c8d8c 
>>>>> 100644
>>>>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>>>>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>>>>> @@ -2170,6 +2170,7 @@ static irqreturn_t dw_hdmi_irq(int irq, void
>>>>> *dev_id)
>>>>>           .name = "DWC HDMI 2.0 TX PHY",
>>>>>           .gen = 2,
>>>>>           .has_svsret = true,
>>>>> +        .configure = hdmi_phy_configure_dwc_hdmi_3d_tx,
>>>>>       }, {
>>>>>           .type = DW_HDMI_PHY_VENDOR_PHY,
>>>>>           .name = "Vendor PHY",
>>
>>
>>
>
>