[linux-sunxi] [PATCH v6 11/13] ARM: dts: sun8i: add DE2 nodes for V3s SoC

[Chen-Yu Tsai]

On Thu, May 4, 2017 at 7:48 PM, Icenowy Zheng <icenowy at aosc.io> wrote:
> Allwinner V3s SoC features a "Display Engine 2.0" with only one TCON
> which have RGB LCD output.

Please also mention that it only has one mixer.

For the subject, you could just say "Add device nodes for the display pipeline".

>
> Add device nodes for it as well as the TCON.
>
> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
> ---
>  arch/arm/boot/dts/sun8i-v3s.dtsi | 87 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 87 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
> index 71075969e5e6..0a895179d8ae 100644
> --- a/arch/arm/boot/dts/sun8i-v3s.dtsi
> +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
> @@ -41,6 +41,10 @@
>   */
>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/sun8i-v3s-ccu.h>
> +#include <dt-bindings/clock/sun8i-de2.h>
> +#include <dt-bindings/reset/sun8i-v3s-ccu.h>
> +#include <dt-bindings/reset/sun8i-de2.h>
>
>  / {
>         #address-cells = <1>;
> @@ -59,6 +63,12 @@
>                 };
>         };
>
> +       de: display-engine {
> +               compatible = "allwinner,sun8i-v3s-display-engine";
> +               allwinner,pipelines = <&de2_mixer0>;
> +               status = "disabled";
> +       };
> +
>         timer {
>                 compatible = "arm,armv7-timer";
>                 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> @@ -93,6 +103,83 @@
>                 #size-cells = <1>;
>                 ranges;
>
> +               de2_clocks: clock at 1000000 {
> +                       compatible = "allwinner,sun50i-h5-de2-clk";

I am a bit skeptical about this. Since the V3S only has one mixer, do the clocks
for the second one even exist?

> +                       reg = <0x01000000 0x100000>;
> +                       clocks = <&ccu CLK_DE>,
> +                                <&ccu CLK_BUS_DE>;
> +                       clock-names = "mod",
> +                                     "bus";
> +                       resets = <&ccu RST_BUS_DE>;
> +                       #clock-cells = <1>;
> +                       #reset-cells = <1>;
> +               };
> +
> +               de2_mixer0: mixer at 1100000 {
> +                       compatible = "allwinner,sun8i-v3s-de2-mixer";
> +                       reg = <0x01100000 0x100000>;
> +                       clocks = <&de2_clocks CLK_MIXER0>,
> +                                <&de2_clocks CLK_BUS_MIXER0>;
> +                       clock-names = "mod",
> +                                     "bus";

Nit: could you list the bus clock first?

Regards
ChenYu

> +                       resets = <&de2_clocks RST_MIXER0>;
> +                       assigned-clocks = <&de2_clocks CLK_MIXER0>;
> +                       assigned-clock-rates = <150000000>;
> +
> +                       ports {
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +
> +                               mixer0_out: port at 1 {
> +                                       #address-cells = <1>;
> +                                       #size-cells = <0>;
> +                                       reg = <1>;
> +
> +                                       mixer0_out_tcon0: endpoint at 0 {
> +                                               reg = <0>;
> +                                               remote-endpoint = <&tcon0_in_mixer0>;
> +                                       };
> +                               };
> +                       };
> +               };
> +
> +               tcon0: lcd-controller at 1c0c000 {
> +                       compatible = "allwinner,sun8i-v3s-tcon";
> +                       reg = <0x01c0c000 0x1000>;
> +                       interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> +                       clocks = <&ccu CLK_BUS_TCON0>,
> +                                <&ccu CLK_TCON0>;
> +                       clock-names = "ahb",
> +                                     "tcon-ch0";
> +                       clock-output-names = "tcon-pixel-clock";
> +                       resets = <&ccu RST_BUS_TCON0>;
> +                       reset-names = "lcd";
> +                       status = "disabled";
> +
> +                       ports {
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +
> +                               tcon0_in: port at 0 {
> +                                       #address-cells = <1>;
> +                                       #size-cells = <0>;
> +                                       reg = <0>;
> +
> +                                       tcon0_in_mixer0: endpoint at 0 {
> +                                               reg = <0>;
> +                                               remote-endpoint = <&mixer0_out_tcon0>;
> +                                       };
> +                               };
> +
> +                               tcon0_out: port at 1 {
> +                                       #address-cells = <1>;
> +                                       #size-cells = <0>;
> +                                       reg = <1>;
> +                               };
> +                       };
> +               };
> +
> +
>                 mmc0: mmc at 01c0f000 {
>                         compatible = "allwinner,sun7i-a20-mmc";
>                         reg = <0x01c0f000 0x1000>;
> --
> 2.12.2
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.