[PATCH v6 9/9] drm/i915: Set PWM divider to match desired frequency in vbt

Puthikorn Voravootivat puthik at chromium.org
Tue May 9 23:40:52 UTC 2017


Read desired PWM frequency from panel vbt and calculate the
value for divider in DPCD address 0x724 and 0x728 to have
as many bits as possible for PWM duty cyle for granularity of
brightness adjustment while the frequency is still within 25%
of the desired frequency.

Signed-off-by: Puthikorn Voravootivat <puthik at chromium.org>
---
 drivers/gpu/drm/i915/intel_dp_aux_backlight.c | 81 +++++++++++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
index fc26fea94fd4..0549ccb1bb09 100644
--- a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
+++ b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
@@ -113,12 +113,86 @@ intel_dp_aux_set_dynamic_backlight_percent(struct intel_dp *intel_dp,
 	}
 }
 
+/*
+ * Set PWM Frequency divider to match desired frequency in vbt.
+ * The PWM Frequency is calculated as 27Mhz / (F x P).
+ * - Where F = PWM Frequency Pre-Divider value programmed by field 7:0 of the
+ *             EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h)
+ * - Where P = 2^Pn, where Pn is the value programmed by field 4:0 of the
+ *             EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h)
+ */
+static void intel_dp_aux_set_pwm_freq(struct intel_connector *connector)
+{
+	struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+	struct intel_dp *intel_dp = enc_to_intel_dp(&connector->encoder->base);
+	int freq, fxp, f, fxp_min, fxp_max, fxp_actual;
+	u8 pn, pn_min, pn_max;
+
+	/* Find desired value of (F x P)
+	 * Note that, if F x P is out of supported range, the maximum value or
+	 * minimum value will applied automatically. So no need to check that.
+	 */
+	freq = dev_priv->vbt.backlight.pwm_freq_hz;
+	DRM_DEBUG_KMS("VBT defined backlight frequency %u Hz\n", freq);
+	if (!freq) {
+		DRM_DEBUG_KMS("Use panel default backlight frequency\n");
+		return;
+	}
+
+	fxp = DP_EDP_BACKLIGHT_FREQ_BASE / freq;
+
+	/* Use highest possible value of Pn for more granularity of brightness
+	 * adjustment while satifying the conditions below.
+	 * - Pn is in the range of Pn_min and Pn_max
+	 * - F is in the range of 1 and 255
+	 * - Effective frequency is within 25% of desired frequency.
+	 */
+	if (drm_dp_dpcd_readb(&intel_dp->aux,
+			       DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min) != 1) {
+		DRM_DEBUG_KMS("Failed to read pwmgen bit count cap min\n");
+		return;
+	}
+	if (drm_dp_dpcd_readb(&intel_dp->aux,
+			       DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max) != 1) {
+		DRM_DEBUG_KMS("Failed to read pwmgen bit count cap max\n");
+		return;
+	}
+	pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
+	pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
+
+	fxp_min = fxp * 3 / 4;
+	fxp_max = fxp * 5 / 4;
+	if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) {
+		DRM_DEBUG_KMS("VBT defined backlight frequency out of range\n");
+		return;
+	}
+
+	for (pn = pn_max; pn > pn_min; pn--) {
+		f = clamp(fxp >> pn, 1, 255);
+		fxp_actual = f << pn;
+		if (fxp_min <= fxp_actual && fxp_actual <= fxp_max)
+			break;
+	}
+
+	if (drm_dp_dpcd_writeb(&intel_dp->aux,
+			       DP_EDP_PWMGEN_BIT_COUNT, pn) < 0) {
+		DRM_DEBUG_KMS("Failed to write aux pwmgen bit count\n");
+		return;
+	}
+	if (drm_dp_dpcd_writeb(&intel_dp->aux,
+			       DP_EDP_BACKLIGHT_FREQ_SET, (u8) f) < 0) {
+		DRM_DEBUG_KMS("Failed to write aux backlight freq\n");
+		return;
+	}
+}
+
 static void intel_dp_aux_enable_backlight(struct intel_connector *connector)
 {
 	struct intel_dp *intel_dp = enc_to_intel_dp(&connector->encoder->base);
 	uint8_t dpcd_buf = 0;
 	uint8_t new_dpcd_buf = 0;
 	uint8_t edp_backlight_mode = 0;
+	bool freq_cap;
 
 	if (drm_dp_dpcd_readb(&intel_dp->aux,
 			DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf) != 1) {
@@ -150,6 +224,10 @@ static void intel_dp_aux_enable_backlight(struct intel_connector *connector)
 		DRM_DEBUG_KMS("Enable dynamic brightness.\n");
 	}
 
+	freq_cap = intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP;
+	if (freq_cap)
+		new_dpcd_buf |= DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
+
 	if (new_dpcd_buf != dpcd_buf) {
 		if (drm_dp_dpcd_writeb(&intel_dp->aux,
 			DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf) < 0) {
@@ -157,6 +235,9 @@ static void intel_dp_aux_enable_backlight(struct intel_connector *connector)
 		}
 	}
 
+	if (freq_cap)
+		intel_dp_aux_set_pwm_freq(connector);
+
 	set_aux_backlight_enable(intel_dp, true);
 	intel_dp_aux_set_backlight(connector, connector->panel.backlight.level);
 }
-- 
2.13.0.rc2.291.g57267f2277-goog



More information about the dri-devel mailing list