[RESEND RFC PATCH 4/7] dt-bindings: Document Allwinner DWC HDMI TX node

Rob Herring robh at kernel.org
Wed Sep 27 21:56:38 UTC 2017


On Wed, Sep 20, 2017 at 10:01:21PM +0200, Jernej Skrabec wrote:
> Add documentation about Allwinner DWC HDMI TX node, found in H3 SoC.
> 
> Signed-off-by: Jernej Skrabec <jernej.skrabec at siol.net>
> ---
>  .../bindings/display/sunxi/sun4i-drm.txt           | 158 ++++++++++++++++++++-
>  1 file changed, 157 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> index 92512953943e..cb6aee5c486f 100644
> --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> @@ -60,6 +60,40 @@ Required properties:
>      first port should be the input endpoint. The second should be the
>      output, usually to an HDMI connector.
>  
> +DWC HDMI TX Encoder
> +-----------------------------
> +
> +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
> +with Allwinner's own PHY IP. It supports audio and video outputs and CEC.
> +
> +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
> +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
> +following device-specific properties.
> +
> +Required properties:
> +
> +  - compatible: value must be one of:
> +    * "allwinner,sun8i-h3-dw-hdmi"
> +  - reg: two pairs of base address and size of memory-mapped region, first
> +    for controller and second for PHY
> +    registers.
> +  - reg-io-width: See dw_hdmi.txt. Shall be 1.
> +  - interrupts: HDMI interrupt number
> +  - clocks: phandles to the clocks feeding the HDMI encoder
> +    * iahb: the HDMI interface clock
> +    * isfr: the HDMI module clock
> +    * ddc: the HDMI ddc clock
> +  - clock-names: the clock names mentioned above
> +  - resets: phandles to the reset controllers driving the encoder
> +    * hdmi: the reset line for the HDMI
> +    * ddc: the reset line for the DDC
> +  - reset-names: the reset names mentioned above
> +
> +  - ports: A ports node with endpoint definitions as defined in
> +    Documentation/devicetree/bindings/media/video-interfaces.txt. The
> +    first port should be the input endpoint. The second should be the
> +    output, usually to an HDMI connector.
> +
>  TV Encoder
>  ----------
>  
> @@ -255,7 +289,7 @@ Required properties:
>    - allwinner,pipelines: list of phandle to the display engine
>      frontends (DE 1.0) or mixers (DE 2.0) available.
>  
> -Example:
> +Example 1:
>  
>  panel: panel {
>  	compatible = "olimex,lcd-olinuxino-43-ts";
> @@ -455,3 +489,125 @@ display-engine {
>  	compatible = "allwinner,sun5i-a13-display-engine";
>  	allwinner,pipelines = <&fe0>;
>  };
> +
> +Example 2:
> +
> +connector {
> +	compatible = "hdmi-connector";
> +	type = "a";
> +
> +	port {
> +		hdmi_con_in: endpoint {
> +			remote-endpoint = <&hdmi_out_con>;
> +		};
> +	};
> +};
> +
> +de: display-engine {
> +	compatible = "allwinner,sun8i-h3-display-engine";
> +	allwinner,pipelines = <&mixer0>;
> +};
> +
> +hdmi: hdmi at 1ee0000 {
> +	compatible = "allwinner,h3-dw-hdmi";
> +	reg = <0x01ee0000 0x10000>,
> +	      <0x01ef0000 0x10000>;
> +	reg-io-width = <1>;
> +	interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
> +	clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI>,
> +		 <&ccu CLK_HDMI_DDC>;
> +	clock-names = "iahb", "isfr", "ddc";
> +	resets = <&ccu RST_BUS_HDMI0>, <&ccu RST_BUS_HDMI1>;
> +	reset-names = "hdmi", "ddc";
> +
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		hdmi_in: port at 0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			hdmi_in_tcon0: endpoint at 0 {
> +				reg = <0>;

You don't need reg when there's only one.

Otherwise,

Acked-by: Rob Herring <robh at kernel.org>


More information about the dri-devel mailing list