[Intel-gfx] [PATCH 1/5] drm/dp/mst: Configure no_stop_bit correctly for remote i2c xfers

[Dhinakaran Pandiyan]

On Fri, 2018-12-07 at 12:45 -0800, Dhinakaran Pandiyan wrote:
> On Fri, 2018-09-28 at 21:03 +0300, Ville Syrjala wrote:
> > From: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > 
> > We aren't supposed to force a stop+start between every i2c msg
> > when performing multi message transfers. This should eg. cause
> > the DDC segment address to be reset back to 0 between writing
> > the segment address and reading the actual EDID extension block.
> > 
> > To quote the E-DDC spec:
> > "... this standard requires that the segment pointer be
> >  reset to 00h when a NO ACK or a STOP condition is received."
> 
> Related question, do you know why the segment and ddc addresses are
> defined as 0x30 and 0x50? The E-DDC spec says they should be at 0x60
> and 0xA0/0xA1.
> 
> > 
> > Since we're going to touch this might as well consult the
> > I2C_M_STOP flag to determine whether we want to force the stop
> > or not.
> 
> Reviewing this took a lot of spec reading than I expected.
> 
> Setting the no_stop_bit after writing the segment address makes
> sense.
> I have one concern though. drm_do_probe_ddc_edid does not make use of
> the I2C_M_STOP flag, which in turn means we won't reset the
> no_stop_bit
> at the end of edid read. Pass the i2c stop flag from the caller?
> 
Never mind, the no_stop_bit is relevant only between i2c writes.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan at intel.com>

> 
> > 
> > Cc: Brian Vincent <brainn at gmail.com>
> > References: https://bugs.freedesktop.org/show_bug.cgi?id=108081
> > Signed-off-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
> > ---
> >  drivers/gpu/drm/drm_dp_mst_topology.c | 1 +
> >  1 file changed, 1 insertion(+)
> > 
> > diff --git a/drivers/gpu/drm/drm_dp_mst_topology.c
> > b/drivers/gpu/drm/drm_dp_mst_topology.c
> > index 5ff1d79b86c4..3b400eab18a2 100644
> > --- a/drivers/gpu/drm/drm_dp_mst_topology.c
> > +++ b/drivers/gpu/drm/drm_dp_mst_topology.c
> > @@ -3276,6 +3276,7 @@ static int drm_dp_mst_i2c_xfer(struct
> > i2c_adapter *adapter, struct i2c_msg *msgs
> >  		msg.u.i2c_read.transactions[i].i2c_dev_id =
> > msgs[i].addr;
> >  		msg.u.i2c_read.transactions[i].num_bytes = msgs[i].len;
> >  		msg.u.i2c_read.transactions[i].bytes = msgs[i].buf;
> > +		msg.u.i2c_read.transactions[i].no_stop_bit =
> > !(msgs[i].flags & I2C_M_STOP);
> >  	}
> >  	msg.u.i2c_read.read_i2c_device_id = msgs[num - 1].addr;
> >  	msg.u.i2c_read.num_bytes_read = msgs[num - 1].len;