[PATCH] drm/vc4: Enable the DSI module and link before other enables.
Kevin Quigley
kevin at kquigley.co.uk
Thu Jun 7 17:22:38 UTC 2018
Hi,
When we talk about control bus enable and video transfer enable for DSI, there is a mode in which control commands can be sent, interleaved with the video. This is often done at the end-of-frame and/or end of line. I've seen this handled in some other DSI device drivers. In these cases, the driver has to look at the frame timing in the video and carefully select the number of control bytes which can be sent during the blanking periods. The number of bytes which can be sent, is very much dependant on the panel-size and clock frequencies... (which determines the blanking time). I'm not sure how widely this is a feature in the DSI encoder HW, and/or implemented purely in the drivers.
I have seen panel drivers - that send commands along DSI, whilst video is streaming. They do this for e.g. to change panel brightness, etc... (which is usually only a small number of bytes). For info, a typical panel start-up scenario is:
- Enable/configure panel HW
- Start Video frames (allowing for the HW & panel's internal regulators to "settle)
- Switch on the Display
To conclude: I think that DSI encoder devices need to be able to support sending control data (LPDA) - concurrently with video frames.
This might make a difference when talking about how to setup and tear down these devices. For one panel we're working with, we have 250-300 bytes of configuration data to send down; so we would prefer to ensure that's sent -before- we enable the video stream to the panel device.
Regards
Kevin
-----Original Message-----
From: Andrzej Hajda [mailto:a.hajda at samsung.com]
Sent: 05 June 2018 09:26
To: Eric Anholt; dri-devel at lists.freedesktop.org
Cc: Kevin Quigley; Boris Brezillon; linux-kernel at vger.kernel.org; James Hughes; Archit Taneja
Subject: Re: [PATCH] drm/vc4: Enable the DSI module and link before other enables.
On 04.06.2018 21:44, Eric Anholt wrote:
> We want the DSI PHY to be enabled and the DSI module clocked before a
> panel or bridge's prepare() function, since most DSI panel drivers
> with a prepare() hook are doing DCS transactions inside of them.
>
> Signed-off-by: Eric Anholt <eric at anholt.net>
> Cc: Kevin Quigley <kevin at kquigley.co.uk>
> Cc: James Hughes <james.hughes at raspberrypi.org>
> Cc: Boris Brezillon <boris.brezillon at bootlin.com>
> ---
>
> I'm not sure it makes sense to enable CRTCs before encoders on vc4 at
> all. Why start scanning pixels before the encoder is ready to hear
> about VSTART? However, this patch will hopefully unblock people
> trying to attach other panels to rpi
But this patch is about enabling encoder before panel/bridge prepare. Or am I missing something.
Anyway I would be more precise here, MIPI-DSI bus is used for two things:
- control bus - accessing DSI device (configuration/detection,...),
- video data bus - sending video stream.
I suspect in prepare/pre_enable phase of DSI panel/bridge only control bus should be functional, video stream transfer does not make sense.
So the best solution (I guess) would be to split DSI-encoder enable sequence into control bus enable and video transfer enable parts and call the former before 1st transfer request from device and the latter in encoder enable callback. Of course there will be a problem then with disabling sequence, ie stopping video stream should be performed in encoder's disable, but when we should disable control bus? If we do it in encoder's disable callback we could not perform transfers in post_disable cb of the bridge - in most cases (maybe all currently present in kernel) it will work, but it does not look ideal.
All this recalls me discussion that hardwiring bridge callbacks into drm core is problematic and maybe it would be better to call downstream callbacks explicitly from upstream element - the callback order should depend on the local bus protocol, and should not be fixed in drm core.
Regards
Andrzej
>
> drivers/gpu/drm/vc4/vc4_drv.h | 1 +
> drivers/gpu/drm/vc4/vc4_dsi.c | 3 +-- drivers/gpu/drm/vc4/vc4_kms.c
> | 25 +++++++++++++++++++++++++
> 3 files changed, 27 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/vc4/vc4_drv.h
> b/drivers/gpu/drm/vc4/vc4_drv.h index 554a4e810d5b..e7d7bfc75acd
> 100644
> --- a/drivers/gpu/drm/vc4/vc4_drv.h
> +++ b/drivers/gpu/drm/vc4/vc4_drv.h
> @@ -711,6 +711,7 @@ int vc4_dpi_debugfs_regs(struct seq_file *m, void
> *unused);
> /* vc4_dsi.c */
> extern struct platform_driver vc4_dsi_driver; int
> vc4_dsi_debugfs_regs(struct seq_file *m, void *unused);
> +void vc4_dsi_prepare(struct drm_encoder *encoder);
>
> /* vc4_fence.c */
> extern const struct dma_fence_ops vc4_fence_ops; diff --git
> a/drivers/gpu/drm/vc4/vc4_dsi.c b/drivers/gpu/drm/vc4/vc4_dsi.c index
> 8aa897835118..88471731e066 100644
> --- a/drivers/gpu/drm/vc4/vc4_dsi.c
> +++ b/drivers/gpu/drm/vc4/vc4_dsi.c
> @@ -875,7 +875,7 @@ static bool vc4_dsi_encoder_mode_fixup(struct drm_encoder *encoder,
> return true;
> }
>
> -static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
> +void vc4_dsi_prepare(struct drm_encoder *encoder)
> {
> struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
> struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
> @@ -1345,7 +1345,6 @@ static const struct mipi_dsi_host_ops
> vc4_dsi_host_ops = {
>
> static const struct drm_encoder_helper_funcs vc4_dsi_encoder_helper_funcs = {
> .disable = vc4_dsi_encoder_disable,
> - .enable = vc4_dsi_encoder_enable,
> .mode_fixup = vc4_dsi_encoder_mode_fixup, };
>
> diff --git a/drivers/gpu/drm/vc4/vc4_kms.c
> b/drivers/gpu/drm/vc4/vc4_kms.c index 8a411e5f8776..7e9b52ba3448
> 100644
> --- a/drivers/gpu/drm/vc4/vc4_kms.c
> +++ b/drivers/gpu/drm/vc4/vc4_kms.c
> @@ -140,6 +140,9 @@ vc4_atomic_complete_commit(struct drm_atomic_state
> *state) {
> struct drm_device *dev = state->dev;
> struct vc4_dev *vc4 = to_vc4_dev(dev);
> + struct drm_connector *connector;
> + struct drm_connector_state *new_conn_state;
> + int i;
>
> drm_atomic_helper_wait_for_fences(dev, state, false);
>
> @@ -151,6 +154,28 @@ vc4_atomic_complete_commit(struct
> drm_atomic_state *state)
>
> drm_atomic_helper_commit_planes(dev, state, 0);
>
> + /* Enable DSI link. */
> + for_each_new_connector_in_state(state, connector, new_conn_state, i) {
> + struct drm_encoder *encoder;
> + struct vc4_encoder *vc4_encoder;
> +
> + if (!new_conn_state->best_encoder)
> + continue;
> +
> + if (!new_conn_state->crtc->state->active ||
> + !drm_atomic_crtc_needs_modeset(new_conn_state->crtc->state))
> + continue;
> +
> + (void)connector;
> + encoder = new_conn_state->best_encoder;
> + vc4_encoder = to_vc4_encoder(encoder);
> +
> + if (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
> + vc4_encoder->type == VC4_ENCODER_TYPE_DSI1) {
> + vc4_dsi_prepare(encoder);
> + }
> + }
> +
> drm_atomic_helper_commit_modeset_enables(dev, state);
>
> /* Make sure that drm_atomic_helper_wait_for_vblanks()
More information about the dri-devel
mailing list