[PATCH] Revert "drm/sun4i: Handle DRM_BUS_FLAG_PIXDATA_*EDGE"
Paul Kocialkowski
paul.kocialkowski at bootlin.com
Wed Jun 13 08:16:47 UTC 2018
This reverts commit 2c17a4368aad2b88b68e4390c819e226cf320f70.
The offending commit triggers a run-time fault when accessing the panel
element of the sun4i_tcon structure when no such panel is attached.
It was apparently assumed in said commit that a panel is always used with
the TCON. Although it is often the case, this is not always true.
For instance a bridge might be used instead of a panel.
This issue was discovered using an A13-OLinuXino, that uses the TCON
in RGB mode for a simple DAC-based VGA bridge.
Cc: stable at vger.kernel.org
Signed-off-by: Paul Kocialkowski <paul.kocialkowski at bootlin.com>
---
drivers/gpu/drm/sun4i/sun4i_tcon.c | 25 -------------------------
1 file changed, 25 deletions(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index c3d92d537240..8045871335b5 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -17,7 +17,6 @@
#include <drm/drm_encoder.h>
#include <drm/drm_modes.h>
#include <drm/drm_of.h>
-#include <drm/drm_panel.h>
#include <uapi/drm/drm_mode.h>
@@ -350,9 +349,6 @@ static void sun4i_tcon0_mode_set_lvds(struct sun4i_tcon *tcon,
static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
const struct drm_display_mode *mode)
{
- struct drm_panel *panel = tcon->panel;
- struct drm_connector *connector = panel->connector;
- struct drm_display_info display_info = connector->display_info;
unsigned int bp, hsync, vsync;
u8 clk_delay;
u32 val = 0;
@@ -410,27 +406,6 @@ static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
if (mode->flags & DRM_MODE_FLAG_PVSYNC)
val |= SUN4I_TCON0_IO_POL_VSYNC_POSITIVE;
- /*
- * On A20 and similar SoCs, the only way to achieve Positive Edge
- * (Rising Edge), is setting dclk clock phase to 2/3(240°).
- * By default TCON works in Negative Edge(Falling Edge),
- * this is why phase is set to 0 in that case.
- * Unfortunately there's no way to logically invert dclk through
- * IO_POL register.
- * The only acceptable way to work, triple checked with scope,
- * is using clock phase set to 0° for Negative Edge and set to 240°
- * for Positive Edge.
- * On A33 and similar SoCs there would be a 90° phase option,
- * but it divides also dclk by 2.
- * Following code is a way to avoid quirks all around TCON
- * and DOTCLOCK drivers.
- */
- if (display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_POSEDGE)
- clk_set_phase(tcon->dclk, 240);
-
- if (display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_NEGEDGE)
- clk_set_phase(tcon->dclk, 0);
-
regmap_update_bits(tcon->regs, SUN4I_TCON0_IO_POL_REG,
SUN4I_TCON0_IO_POL_HSYNC_POSITIVE | SUN4I_TCON0_IO_POL_VSYNC_POSITIVE,
val);
--
2.17.0
More information about the dri-devel
mailing list