[PATCH V3 4/7] backlight: qcom-wled: Rename PM8941* to WLED3

[kgunda at codeaurora.org]

On 2018-06-20 04:41, Bjorn Andersson wrote:
> On Tue 19 Jun 04:13 PDT 2018, Kiran Gunda wrote:
> 
>> Rename the PM8941* references as WLED3 to make the
>> driver generic and have WLED support for other PMICs.
>> 
> 
> Looks good, just three minor comments below.
> 
>> Signed-off-by: Kiran Gunda <kgunda at codeaurora.org>
>> ---
>>  drivers/video/backlight/qcom-wled.c | 248 
>> ++++++++++++++++++------------------
>>  1 file changed, 125 insertions(+), 123 deletions(-)
>> 
>> diff --git a/drivers/video/backlight/qcom-wled.c 
>> b/drivers/video/backlight/qcom-wled.c
>> index 0b6d219..812f3cb 100644
>> --- a/drivers/video/backlight/qcom-wled.c
>> +++ b/drivers/video/backlight/qcom-wled.c
>> @@ -18,77 +18,79 @@
>>  #include <linux/regmap.h>
>> 
>>  /* From DT binding */
>> -#define PM8941_WLED_DEFAULT_BRIGHTNESS		2048
>> +#define WLED_DEFAULT_BRIGHTNESS				2048
>> 
>> -#define PM8941_WLED_REG_VAL_BASE		0x40
>> -#define  PM8941_WLED_REG_VAL_MAX		0xFFF
>> +#define WLED3_SINK_REG_BRIGHT_MAX			0xFFF
>> +#define WLED3_CTRL_REG_VAL_BASE				0x40
>> 
>> -#define PM8941_WLED_REG_MOD_EN			0x46
>> -#define  PM8941_WLED_REG_MOD_EN_BIT		BIT(7)
>> -#define  PM8941_WLED_REG_MOD_EN_MASK		BIT(7)
>> +/* WLED3 control registers */
>> +#define WLED3_CTRL_REG_MOD_EN				0x46
>> +#define  WLED3_CTRL_REG_MOD_EN_BIT			BIT(7)
>> +#define  WLED3_CTRL_REG_MOD_EN_MASK			BIT(7)
>> 
>> -#define PM8941_WLED_REG_SYNC			0x47
> 
> These are in address order, any reason why WLED3_SINK_REG_SYNC moved
> down?
> 
Actually, this is a sink specific register. That's why moved it to
under the /* WLED3 sink specific registers */
>> -#define  PM8941_WLED_REG_SYNC_MASK		0x07
>> -#define  PM8941_WLED_REG_SYNC_LED1		BIT(0)
>> -#define  PM8941_WLED_REG_SYNC_LED2		BIT(1)
>> -#define  PM8941_WLED_REG_SYNC_LED3		BIT(2)
>> -#define  PM8941_WLED_REG_SYNC_ALL		0x07
>> -#define  PM8941_WLED_REG_SYNC_CLEAR		0x00
>> +#define WLED3_CTRL_REG_FREQ				0x4c
>> +#define  WLED3_CTRL_REG_FREQ_MASK			0x0f
>> 
>> -#define PM8941_WLED_REG_FREQ			0x4c
>> -#define  PM8941_WLED_REG_FREQ_MASK		0x0f
>> +#define WLED3_CTRL_REG_OVP				0x4d
>> +#define  WLED3_CTRL_REG_OVP_MASK			0x03
>> 
>> -#define PM8941_WLED_REG_OVP			0x4d
>> -#define  PM8941_WLED_REG_OVP_MASK		0x03
>> +#define WLED3_CTRL_REG_ILIMIT				0x4e
>> +#define  WLED3_CTRL_REG_ILIMIT_MASK			0x07
>> 
>> -#define PM8941_WLED_REG_BOOST			0x4e
>> -#define  PM8941_WLED_REG_BOOST_MASK		0x07
>> +/* WLED3 sink registers */
>> +#define WLED3_SINK_REG_SYNC				0x47
>> +#define  WLED3_SINK_REG_SYNC_MASK			0x07
>> +#define  WLED3_SINK_REG_SYNC_LED1			BIT(0)
>> +#define  WLED3_SINK_REG_SYNC_LED2			BIT(1)
>> +#define  WLED3_SINK_REG_SYNC_LED3			BIT(2)
>> +#define  WLED3_SINK_REG_SYNC_ALL			0x07
>> +#define  WLED3_SINK_REG_SYNC_CLEAR			0x00
>> 
> [..]
>> -struct pm8941_wled_config {
>> -	u32 i_boost_limit;
>> +struct wled_config {
>> +	u32 boost_i_limit;
>>  	u32 ovp;
>>  	u32 switch_freq;
>>  	u32 num_strings;
>> -	u32 i_limit;
>> +	u32 string_i_limit;
> 
> Changing the members in this struct seems unrelated.
> 
Changed the members, to have resemblance with the IPCAT and
better readability .
>>  	bool cs_out_en;
>>  	bool ext_gen;
>>  	bool cabc_en;
>>  };
>> 
> [..]
>> -MODULE_DESCRIPTION("pm8941 wled driver");
>> +MODULE_DESCRIPTION("qcom wled driver");
> 
> I would prefer if this was "Qualcomm WLED driver".
> 
Sure. I will change it in the next series.
>>  MODULE_LICENSE("GPL v2");
> 
> Regards,
> Bjorn