[PATCH v3 23/24] ARM: dts: sun8i: r40: Add HDMI pipeline
Jernej Škrabec
jernej.skrabec at siol.net
Thu Jun 28 05:15:18 UTC 2018
Dne četrtek, 28. junij 2018 ob 04:50:09 CEST je Chen-Yu Tsai napisal(a):
> On Mon, Jun 25, 2018 at 8:03 PM, Jernej Skrabec <jernej.skrabec at siol.net>
wrote:
> > Add all entries needed for HDMI to function properly.
> >
> > Since R40 has highly configurable pipeline, both mixers and both TCON
> > TVs are added. Board specific DT should then connect them together
> > trough TCON TOP muxers to best fit the purpose of the board.
> >
> > Signed-off-by: Jernej Skrabec <jernej.skrabec at siol.net>
> > ---
> >
> > arch/arm/boot/dts/sun8i-r40.dtsi | 269 +++++++++++++++++++++++++++++++
> > 1 file changed, 269 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi
> > b/arch/arm/boot/dts/sun8i-r40.dtsi index 173dcc1652d2..a2a75fb04caf
> > 100644
> > --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> > +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> > @@ -42,8 +42,11 @@
> >
> > */
> >
> > #include <dt-bindings/interrupt-controller/arm-gic.h>
> >
> > +#include <dt-bindings/clock/sun8i-de2.h>
> >
> > #include <dt-bindings/clock/sun8i-r40-ccu.h>
> >
> > +#include <dt-bindings/clock/sun8i-tcon-top.h>
Maxime, above line breaks compilation for build robot, sorry.
> >
> > #include <dt-bindings/reset/sun8i-r40-ccu.h>
> >
> > +#include <dt-bindings/reset/sun8i-de2.h>
> >
> > / {
> >
> > #address-cells = <1>;
> >
> > @@ -99,12 +102,76 @@
> >
> > };
> >
> > };
> >
> > + de: display-engine {
> > + compatible = "allwinner,sun8i-r40-display-engine",
> > + "allwinner,sun8i-h3-display-engine";
>
> Given that the display pipeline looks different, they should not be
> compatible.
Ok.
>
> > + allwinner,pipelines = <&mixer0>, <&mixer1>;
> > + status = "disabled";
> > + };
> > +
> >
> > soc {
> >
> > compatible = "simple-bus";
> > #address-cells = <1>;
> > #size-cells = <1>;
> > ranges;
> >
> > + display_clocks: clock at 1000000 {
> > + compatible = "allwinner,sun8i-r40-de2-clk",
> > + "allwinner,sun8i-h3-de2-clk";
> > + reg = <0x01000000 0x100000>;
> > + clocks = <&ccu CLK_DE>,
> > + <&ccu CLK_BUS_DE>;
> > + clock-names = "mod",
> > + "bus";
> > + resets = <&ccu RST_BUS_DE>;
> > + #clock-cells = <1>;
> > + #reset-cells = <1>;
> > + };
> > +
> > + mixer0: mixer at 1100000 {
> > + compatible = "allwinner,sun8i-r40-de2-mixer-0";
> > + reg = <0x01100000 0x100000>;
> > + clocks = <&display_clocks CLK_BUS_MIXER0>,
> > + <&display_clocks CLK_MIXER0>;
> > + clock-names = "bus",
> > + "mod";
> > + resets = <&display_clocks RST_MIXER0>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + mixer0_out: port at 1 {
> > + reg = <1>;
> > + mixer0_out_tcon_top: endpoint {
> > + remote-endpoint =
> > <&tcon_top_mixer0_in_mixer0>; + };
> > + };
> > + };
> > + };
> > +
> > + mixer1: mixer at 1200000 {
> > + compatible = "allwinner,sun8i-r40-de2-mixer-1";
> > + reg = <0x01200000 0x100000>;
> > + clocks = <&display_clocks CLK_BUS_MIXER1>,
> > + <&display_clocks CLK_MIXER1>;
> > + clock-names = "bus",
> > + "mod";
> > + resets = <&display_clocks RST_WB>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + mixer1_out: port at 1 {
> > + reg = <1>;
> > + mixer1_out_tcon_top: endpoint {
> > + remote-endpoint =
> > <&tcon_top_mixer1_in_mixer1>; + };
> > + };
> > + };
> > + };
> > +
> >
> > nmi_intc: interrupt-controller at 1c00030 {
> >
> > compatible = "allwinner,sun7i-a20-sc-nmi";
> > interrupt-controller;
> >
> > @@ -451,6 +518,163 @@
> >
> > #size-cells = <0>;
> >
> > };
> >
> > + tcon_top: tcon-top at 1c70000 {
> > + compatible = "allwinner,sun8i-r40-tcon-top";
> > + reg = <0x01c70000 0x1000>;
> > + clocks = <&ccu CLK_BUS_TCON_TOP>,
> > + <&ccu CLK_TCON_TV0>,
> > + <&ccu CLK_TVE0>,
> > + <&ccu CLK_TCON_TV1>,
> > + <&ccu CLK_TVE1>,
> > + <&ccu CLK_DSI_DPHY>;
> > + clock-names = "bus",
> > + "tcon-tv0",
> > + "tve0",
> > + "tcon-tv1",
> > + "tve1",
> > + "dsi";
> > + clock-output-names = "tcon-top-tv0",
> > + "tcon-top-tv1",
> > + "tcon-top-dsi";
> > + resets = <&ccu RST_BUS_TCON_TOP>;
> > + #clock-cells = <1>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + tcon_top_mixer0_in: port at 0 {
> > + reg = <0>;
> > +
> > + tcon_top_mixer0_in_mixer0:
> > endpoint { +
> > remote-endpoint = <&mixer0_out_tcon_top>; +
> > };
> > + };
> > +
> > + tcon_top_mixer0_out: port at 1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > +
> > + tcon_top_mixer0_out_tcon_lcd0:
> > endpoint at 0 { + reg = <0>;
> > + };
> > +
> > + tcon_top_mixer0_out_tcon_lcd1:
> > endpoint at 1 { + reg = <1>;
> > + };
> > +
> > + tcon_top_mixer0_out_tcon_tv0:
> > endpoint at 2 { + reg = <2>;
> > + };
> > +
> > + tcon_top_mixer0_out_tcon_tv1:
> > endpoint at 3 { + reg = <3>;
> > + };
> > + };
> > +
> > + tcon_top_mixer1_in: port at 2 {
> > + reg = <2>;
> > +
> > + tcon_top_mixer1_in_mixer1:
> > endpoint { +
> > remote-endpoint = <&mixer1_out_tcon_top>; +
> > };
> > + };
> > +
> > + tcon_top_mixer1_out: port at 3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <3>;
> > +
> > + tcon_top_mixer1_out_tcon_lcd0:
> > endpoint at 0 { + reg = <0>;
> > + };
> > +
> > + tcon_top_mixer1_out_tcon_lcd1:
> > endpoint at 1 { + reg = <1>;
> > + };
> > +
> > + tcon_top_mixer1_out_tcon_tv0:
> > endpoint at 2 { + reg = <2>;
> > + };
> > +
> > + tcon_top_mixer1_out_tcon_tv1:
> > endpoint at 3 { + reg = <3>;
> > + };
> > + };
> > +
> > + tcon_top_hdmi_in: port at 4 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <4>;
> > +
> > + tcon_top_hdmi_in_tcon_tv0:
> > endpoint at 0 { + reg = <0>;
> > + };
> > +
> > + tcon_top_hdmi_in_tcon_tv1:
> > endpoint at 1 { + reg = <1>;
> > + };
> > + };
> > +
> > + tcon_top_hdmi_out: port at 5 {
> > + reg = <5>;
> > +
> > + tcon_top_hdmi_out_hdmi: endpoint {
> > + remote-endpoint =
> > <&hdmi_in_tcon_top>; + };
> > + };
> > + };
> > + };
> > +
> > + tcon_tv0: lcd-controller at 1c73000 {
> > + compatible = "allwinner,sun8i-r40-tcon-tv",
> > + "allwinner,sun8i-a83t-tcon-tv";
> > + reg = <0x01c73000 0x1000>;
> > + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_TCON_TV0>, <&tcon_top 0>;
> > + clock-names = "ahb", "tcon-ch1";
> > + resets = <&ccu RST_BUS_TCON_TV0>;
> > + reset-names = "lcd";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + tcon_tv0_in: port at 0 {
> > + reg = <0>;
> > + };
> > +
> > + tcon_tv0_out: port at 1 {
> > + reg = <1>;
> > + };
> > + };
> > + };
> > +
> > + tcon_tv1: lcd-controller at 1c74000 {
> > + compatible = "allwinner,sun8i-r40-tcon-tv",
> > + "allwinner,sun8i-a83t-tcon-tv";
> > + reg = <0x01c74000 0x1000>;
> > + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_TCON_TV1>, <&tcon_top 1>;
> > + clock-names = "ahb", "tcon-ch1";
> > + resets = <&ccu RST_BUS_TCON_TV1>;
> > + reset-names = "lcd";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + tcon_tv1_in: port at 0 {
> > + reg = <0>;
> > + };
> > +
> > + tcon_tv1_out: port at 1 {
> > + reg = <1>;
>
> You are missing the remote-endpoints for all the TCON-TOP <-> TCON
> connections. Also, on the driver side, there's no code to handle
> dynamically mapping mixers to the TCONs that are being used. In the past we
> had simple 1:1 mappings. This is no longer the case, and it needs to be
> dealt with.
How would TCON TOP driver know how to set muxes? There are no appropriate
bingings for muxes, except for V4L2 subsystem, which doesn't really work here.
Additionaly, how would HDMI know which TCON belongs to it to appropriately set
possible_crtcs?
Currently, my idea is that board DT creates wanted connections. Since there is
only one valid connection for each mux, driver knows eactly what to write into
mux register. HDMI driver can simply check which TCON connection is valid in
HDMI input mux and select it in possible_crtcs.
Please also note that mixer0 and mixer1 don't have same capabilities and you
generally want mixer0 to be connected to main output. This is in contrast to
DE1 SoCs, where both backends and both frontends have same capability.
Best regards,
Jernej
>
> ChenYu
>
> > + };
> > + };
> > + };
> > +
> >
> > gic: interrupt-controller at 1c81000 {
> >
> > compatible = "arm,gic-400";
> > reg = <0x01c81000 0x1000>,
> >
> > @@ -461,6 +685,51 @@
> >
> > #interrupt-cells = <3>;
> > interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
> > IRQ_TYPE_LEVEL_HIGH)>;
> >
> > };
> >
> > +
> > + hdmi: hdmi at 1ee0000 {
> > + compatible = "allwinner,sun8i-r40-dw-hdmi",
> > + "allwinner,sun8i-a83t-dw-hdmi";
> > + reg = <0x01ee0000 0x10000>;
> > + reg-io-width = <1>;
> > + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_HDMI0>, <&ccu
> > CLK_HDMI_SLOW>, + <&ccu CLK_HDMI>;
> > + clock-names = "iahb", "isfr", "tmds";
> > + resets = <&ccu RST_BUS_HDMI1>;
> > + reset-names = "ctrl";
> > + phys = <&hdmi_phy>;
> > + phy-names = "hdmi-phy";
> > + status = "disabled";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + hdmi_in: port at 0 {
> > + reg = <0>;
> > +
> > + hdmi_in_tcon_top: endpoint {
> > + remote-endpoint =
> > <&tcon_top_hdmi_out_hdmi>; + };
> > + };
> > +
> > + hdmi_out: port at 1 {
> > + reg = <1>;
> > + };
> > + };
> > + };
> > +
> > + hdmi_phy: hdmi-phy at 1ef0000 {
> > + compatible = "allwinner,sun8i-r40-hdmi-phy",
> > + "allwinner,sun50i-a64-hdmi-phy";
> > + reg = <0x01ef0000 0x10000>;
> > + clocks = <&ccu CLK_BUS_HDMI1>, <&ccu
> > CLK_HDMI_SLOW>, + <&ccu 7>, <&ccu 16>;
> > + clock-names = "bus", "mod", "pll-0", "pll-1";
> > + resets = <&ccu RST_BUS_HDMI0>;
> > + reset-names = "phy";
> > + #phy-cells = <0>;
> > + };
> >
> > };
> >
> > timer {
> >
> > --
> > 2.18.0
More information about the dri-devel
mailing list