[DPU PATCH v2 1/2] dt-bindings: msm/disp: Remove hw block offset DT entries for SDM845
Sean Paul
seanpaul at chromium.org
Thu Mar 29 14:52:06 UTC 2018
On Thu, Mar 29, 2018 at 03:59:24PM +0530, Sravanthi Kollukuduru wrote:
> Currently, the downstream driver depends on the DT file for the
> hardware block offsets and other target specific catalog information.
> To align the driver with the upstream DT design, this information is now
> removed from the DT file and added in the driver source.
>
Reviewed-by: Sean Paul <seanpaul at chromium.org>
> Change-Id: I63a366d7d7a26939ee1c20c702c7d4d976852067
(btw, please strip these out when you send patches upstream. I will remove it
when applying)
> Signed-off-by: Sravanthi Kollukuduru <skolluku at codeaurora.org>
> ---
> .../devicetree/bindings/display/msm/dpu.txt | 530 ---------------------
> 1 file changed, 530 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
> index 136f0d3..90cd3e0 100644
> --- a/Documentation/devicetree/bindings/display/msm/dpu.txt
> +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
> @@ -19,61 +19,6 @@ Required properties
> - interrupt-controller: Mark the device node as an interrupt controller.
> - #interrupt-cells: Should be one. The first cell is interrupt number.
> - iommus: Specifies the SID's used by this context bank.
> -- qcom,dpu-sspp-type: Array of strings for DPU source surface pipes type information.
> - A source pipe can be "vig", "rgb", "dma" or "cursor" type.
> - Number of xin ids defined should match the number of offsets
> - defined in property: qcom,dpu-sspp-off.
> -- qcom,dpu-sspp-off: Array of offset for DPU source surface pipes. The offsets
> - are calculated from register "mdp_phys" defined in
> - reg property + "dpu-off". The number of offsets defined here should
> - reflect the amount of pipes that can be active in DPU for
> - this configuration.
> -- qcom,dpu-sspp-xin-id: Array of VBIF clients ids (xins) corresponding
> - to the respective source pipes. Number of xin ids
> - defined should match the number of offsets
> - defined in property: qcom,dpu-sspp-off.
> -- qcom,dpu-ctl-off: Array of offset addresses for the available ctl
> - hw blocks within DPU, these offsets are
> - calculated from register "mdp_phys" defined in
> - reg property. The number of ctl offsets defined
> - here should reflect the number of control paths
> - that can be configured concurrently on DPU for
> - this configuration.
> -- qcom,dpu-wb-off: Array of offset addresses for the programmable
> - writeback blocks within DPU.
> -- qcom,dpu-wb-xin-id: Array of VBIF clients ids (xins) corresponding
> - to the respective writeback. Number of xin ids
> - defined should match the number of offsets
> - defined in property: qcom,dpu-wb-off.
> -- qcom,dpu-mixer-off: Array of offset addresses for the available
> - mixer blocks that can drive data to panel
> - interfaces. These offsets are be calculated from
> - register "mdp_phys" defined in reg property.
> - The number of offsets defined should reflect the
> - amount of mixers that can drive data to a panel
> - interface.
> -- qcom,dpu-dspp-top-off: Offset address for the dspp top block.
> - The offset is calculated from register "mdp_phys"
> - defined in reg property.
> -- qcom,dpu-dspp-off: Array of offset addresses for the available dspp
> - blocks. These offsets are calculated from
> - register "mdp_phys" defined in reg property.
> -- qcom,dpu-pp-off: Array of offset addresses for the available
> - pingpong blocks. These offsets are calculated
> - from register "mdp_phys" defined in reg property.
> -- qcom,dpu-pp-slave: Array of flags indicating whether each ping pong
> - block may be configured as a pp slave.
> -- qcom,dpu-intf-off: Array of offset addresses for the available DPU
> - interface blocks that can drive data to a
> - panel controller. The offsets are calculated
> - from "mdp_phys" defined in reg property. The number
> - of offsets defined should reflect the number of
> - programmable interface blocks available in hardware.
> -- qcom,dpu-mixer-blend-op-off Array of offset addresses for the available
> - blending stages. The offsets are relative to
> - qcom,dpu-mixer-off.
> -- qcom,dpu-mixer-pair-mask Array of mixer numbers that can be paired with
> - mixer number corresponding to the array index.
>
> Optional properties:
> - clock-rate: List of clock rates in Hz.
> @@ -93,182 +38,6 @@ Optional properties:
> -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
> -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
> -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
> -- qcom,dpu-sspp-src-size: A u32 value indicates the address range for each sspp.
> -- qcom,dpu-mixer-size: A u32 value indicates the address range for each mixer.
> -- qcom,dpu-ctl-size: A u32 value indicates the address range for each ctl.
> -- qcom,dpu-dspp-size: A u32 value indicates the address range for each dspp.
> -- qcom,dpu-intf-size: A u32 value indicates the address range for each intf.
> -- qcom,dpu-dsc-size: A u32 value indicates the address range for each dsc.
> -- qcom,dpu-cdm-size: A u32 value indicates the address range for each cdm.
> -- qcom,dpu-pp-size: A u32 value indicates the address range for each pingpong.
> -- qcom,dpu-wb-size: A u32 value indicates the address range for each writeback.
> -- qcom,dpu-len: A u32 entry for DPU address range.
> -- qcom,dpu-intf-max-prefetch-lines: Array of u32 values for max prefetch lines on
> - each interface.
> -- qcom,dpu-sspp-linewidth: A u32 value indicates the max sspp line width.
> -- qcom,dpu-mixer-linewidth: A u32 value indicates the max mixer line width.
> -- qcom,dpu-wb-linewidth: A u32 value indicates the max writeback line width.
> -- qcom,dpu-sspp-scale-size: A u32 value indicates the scaling block size on sspp.
> -- qcom,dpu-mixer-blendstages: A u32 value indicates the max mixer blend stages for
> - alpha blending.
> -- qcom,dpu-qseed-type: A string entry indiates qseed support on sspp and wb.
> - It supports "qssedv3" and "qseedv2" entries for qseed
> - type. By default "qseedv2" is used if this optional property
> - is not defined.
> -- qcom,dpu-csc-type: A string entry indicates csc support on sspp and wb.
> - It supports "csc" and "csc-10bit" entries for csc
> - type.
> -- qcom,dpu-highest-bank-bit: A u32 property to indicate GPU/Camera/Video highest memory
> - bank bit used for tile format buffers.
> -- qcom,dpu-ubwc-version: Property to specify the UBWC feature version.
> -- qcom,dpu-ubwc-static: Property to specify the default UBWC static
> - configuration value.
> -- qcom,dpu-ubwc-swizzle: Property to specify the default UBWC swizzle
> - configuration value.
> -- qcom,dpu-panic-per-pipe: Boolean property to indicate if panic signal
> - control feature is available on each source pipe.
> -- qcom,dpu-has-src-split: Boolean property to indicate if source split
> - feature is available or not.
> -- qcom,dpu-has-dim-layer: Boolean property to indicate if mixer has dim layer
> - feature is available or not.
> -- qcom,dpu-has-idle-pc: Boolean property to indicate if target has idle
> - power collapse feature available or not.
> -- qcom,dpu-has-mixer-gc: Boolean property to indicate if mixer has gamma correction
> - feature available or not.
> -- qcom,dpu-has-dest-scaler: Boolean property to indicate if destination scaler
> - feature is available or not.
> -- qcom,dpu-max-dest-scaler-input-linewidth: A u32 value indicates the
> - maximum input line width to destination scaler.
> -- qcom,dpu-max-dest-scaler-output-linewidth: A u32 value indicates the
> - maximum output line width of destination scaler.
> -- qcom,dpu-dest-scaler-top-off: A u32 value provides the
> - offset from mdp base to destination scaler block.
> -- qcom,dpu-dest-scaler-top-size: A u32 value indicates the address range for ds top
> -- qcom,dpu-dest-scaler-off: Array of u32 offsets indicate the qseed3 scaler blocks
> - offset from destination scaler top offset.
> -- qcom,dpu-dest-scaler-size: A u32 value indicates the address range for each scaler block
> -- qcom,dpu-sspp-clk-ctrl: Array of offsets describing clk control
> - offsets for dynamic clock gating. 1st value
> - in the array represents offset of the control
> - register. 2nd value represents bit offset within
> - control register. Number of offsets defined should
> - match the number of offsets defined in
> - property: qcom,dpu-sspp-off
> -- qcom,dpu-sspp-clk-status: Array of offsets describing clk status
> - offsets for dynamic clock gating. 1st value
> - in the array represents offset of the status
> - register. 2nd value represents bit offset within
> - control register. Number of offsets defined should
> - match the number of offsets defined in
> - property: qcom,dpu-sspp-off.
> -- qcom,dpu-sspp-excl-rect: Array of u32 values indicating exclusion rectangle
> - support on each sspp.
> -- qcom,dpu-sspp-smart-dma-priority: Array of u32 values indicating hw pipe
> - priority of secondary rectangles when smart dma
> - is supported. Number of priority values should
> - match the number of offsets defined in
> - qcom,dpu-sspp-off node. Zero indicates no support
> - for smart dma for the sspp.
> -- qcom,dpu-smart-dma-rev: A string entry indicating the smart dma version
> - supported on the device. Supported entries are
> - "smart_dma_v1" and "smart_dma_v2".
> -- qcom,dpu-intf-type: Array of string provides the interface type information.
> - Possible string values
> - "dsi" - dsi display interface
> - "dp" - Display Port interface
> - "hdmi" - HDMI display interface
> - An interface is considered as "none" if interface type
> - is not defined.
> -- qcom,dpu-off: DPU offset from "mdp_phys" defined in reg property.
> -- qcom,dpu-cdm-off: Array of offset addresses for the available
> - cdm blocks. These offsets will be calculated from
> - register "mdp_phys" defined in reg property.
> -- qcom,dpu-vbif-off: Array of offset addresses for the available
> - vbif blocks. These offsets will be calculated from
> - register "vbif_phys" defined in reg property.
> -- qcom,dpu-vbif-size: A u32 value indicates the vbif block address range.
> -- qcom,dpu-te-off: A u32 offset indicates the te block offset on pingpong.
> - This offset is 0x0 by default.
> -- qcom,dpu-te2-off: A u32 offset indicates the te2 block offset on pingpong.
> -- qcom,dpu-te-size: A u32 value indicates the te block address range.
> -- qcom,dpu-te2-size: A u32 value indicates the te2 block address range.
> -- qcom,dpu-dsc-off: A u32 offset indicates the dsc block offset on pingpong.
> -- qcom,dpu-dither-off: A u32 offset indicates the dither block offset on pingpong.
> -- qcom,dpu-dither-version: A u32 value indicates the dither block version.
> -- qcom,dpu-dither-size: A u32 value indicates the dither block address range.
> -- qcom,dpu-sspp-vig-blocks: A node that lists the blocks inside the VIG hardware. The
> - block entries will contain the offset and version (if needed)
> - of each feature block. The presence of a block entry
> - indicates that the SSPP VIG contains that feature hardware.
> - e.g. qcom,dpu-sspp-vig-blocks
> - -- qcom,dpu-vig-csc-off: offset of CSC hardware
> - -- qcom,dpu-vig-qseed-off: offset of QSEED hardware
> - -- qcom,dpu-vig-qseed-size: A u32 address range for qseed scaler.
> - -- qcom,dpu-vig-pcc: offset and version of PCC hardware
> - -- qcom,dpu-vig-hsic: offset and version of global PA adjustment
> - -- qcom,dpu-vig-memcolor: offset and version of PA memcolor hardware
> -- qcom,dpu-sspp-rgb-blocks: A node that lists the blocks inside the RGB hardware. The
> - block entries will contain the offset and version (if needed)
> - of each feature block. The presence of a block entry
> - indicates that the SSPP RGB contains that feature hardware.
> - e.g. qcom,dpu-sspp-vig-blocks
> - -- qcom,dpu-rgb-scaler-off: offset of RGB scaler hardware
> - -- qcom,dpu-rgb-scaler-size: A u32 address range for scaler.
> - -- qcom,dpu-rgb-pcc: offset and version of PCC hardware
> -- qcom,dpu-dspp-blocks: A node that lists the blocks inside the DSPP hardware. The
> - block entries will contain the offset and version of each
> - feature block. The presence of a block entry indicates that
> - the DSPP contains that feature hardware.
> - e.g. qcom,dpu-dspp-blocks
> - -- qcom,dpu-dspp-pcc: offset and version of PCC hardware
> - -- qcom,dpu-dspp-gc: offset and version of GC hardware
> - -- qcom,dpu-dspp-igc: offset and version of IGC hardware
> - -- qcom,dpu-dspp-hsic: offset and version of global PA adjustment
> - -- qcom,dpu-dspp-memcolor: offset and version of PA memcolor hardware
> - -- qcom,dpu-dspp-sixzone: offset and version of PA sixzone hardware
> - -- qcom,dpu-dspp-gamut: offset and version of Gamut mapping hardware
> - -- qcom,dpu-dspp-dither: offset and version of dither hardware
> - -- qcom,dpu-dspp-hist: offset and version of histogram hardware
> - -- qcom,dpu-dspp-vlut: offset and version of PA vLUT hardware
> -- qcom,dpu-mixer-blocks: A node that lists the blocks inside the layer mixer hardware. The
> - block entries will contain the offset and version (if needed)
> - of each feature block. The presence of a block entry
> - indicates that the layer mixer contains that feature hardware.
> - e.g. qcom,dpu-mixer-blocks
> - -- qcom,dpu-mixer-gc: offset and version of mixer GC hardware
> -- qcom,dpu-dspp-ad-off: Array of u32 offsets indicate the ad block offset from the
> - DSPP offset. Since AD hardware is represented as part of
> - DSPP block, the AD offsets must be offset from the
> - corresponding DSPP base.
> -- qcom,dpu-dspp-ad-version A u32 value indicating the version of the AD hardware
> -- qcom,dpu-vbif-id: Array of vbif ids corresponding to the
> - offsets defined in property: qcom,dpu-vbif-off.
> -- qcom,dpu-vbif-default-ot-rd-limit: A u32 value indicates the default read OT limit
> -- qcom,dpu-vbif-default-ot-wr-limit: A u32 value indicates the default write OT limit
> -- qcom,dpu-vbif-dynamic-ot-rd-limit: A series of 2 cell property, with a format
> - of (pps, OT limit), where pps is pixel per second and
> - OT limit is the read limit to apply if the given
> - pps is not exceeded.
> -- qcom,dpu-vbif-dynamic-ot-wr-limit: A series of 2 cell property, with a format
> - of (pps, OT limit), where pps is pixel per second and
> - OT limit is the write limit to apply if the given
> - pps is not exceeded.
> -- qcom,dpu-vbif-memtype-0: Array of u32 vbif memory type settings, group 0
> -- qcom,dpu-vbif-memtype-1: Array of u32 vbif memory type settings, group 1
> -- qcom,dpu-wb-id: Array of writeback ids corresponding to the
> - offsets defined in property: qcom,dpu-wb-off.
> -- qcom,dpu-wb-clk-ctrl: Array of 2 cell property describing clk control
> - offsets for dynamic clock gating. 1st value
> - in the array represents offset of the control
> - register. 2nd value represents bit offset within
> - control register. Number of offsets defined should
> - match the number of offsets defined in
> - property: qcom,dpu-wb-off
> -- qcom,dpu-reg-dma-off: Offset of the register dma hardware block from
> - "regdma_phys" defined in reg property.
> -- qcom,dpu-reg-dma-version: Version of the reg dma hardware block.
> -- qcom,dpu-reg-dma-trigger-off: Offset of the lut dma trigger reg from "mdp_phys"
> - defined in reg property.
> - qcom,dpu-dram-channels: This represents the number of channels in the
> Bus memory controller.
> - qcom,dpu-num-nrt-paths: Integer property represents the number of non-realtime
> @@ -277,95 +46,6 @@ Optional properties:
> for particular chipset.
> These paths must be defined after rt-paths in
> "qcom,msm-bus,vectors-KBps" vector request.
> -- qcom,dpu-max-bw-low-kbps: This value indicates the max bandwidth in Kbps
> - that can be supported without underflow.
> - This is a low bandwidth threshold which should
> - be applied in most scenarios to be safe from
> - underflows when unable to satisfy bandwidth
> - requirements.
> -- qcom,dpu-max-bw-high-kbps: This value indicates the max bandwidth in Kbps
> - that can be supported without underflow.
> - This is a high bandwidth threshold which can be
> - applied in scenarios where panel interface can
> - be more tolerant to memory latency such as
> - command mode panels.
> -- qcom,dpu-core-ib-ff: A string entry indicating the fudge factor for
> - core ib calculation.
> -- qcom,dpu-core-clk-ff: A string entry indicating the fudge factor for
> - core clock calculation.
> -- qcom,dpu-min-core-ib-kbps: This u32 value indicates the minimum mnoc ib
> - vote in Kbps that can be reduced without hitting underflow.
> - BW calculation logic will choose the IB bandwidth requirement
> - based on usecase if this floor value is not defined.
> -- qcom,dpu-min-llcc-ib-kbps: This u32 value indicates the minimum llcc ib
> - vote in Kbps that can be reduced without hitting underflow.
> - BW calculation logic will choose the IB bandwidth requirement
> - based on usecase if this floor value is not defined.
> -- qcom,dpu-min-dram-ib-kbps: This u32 value indicates the minimum dram ib
> - vote in Kbps that can be reduced without hitting underflow.
> - BW calculation logic will choose the IB bandwidth requirement
> - based on usecase if this floor value is not defined.
> -- qcom,dpu-comp-ratio-rt: A string entry indicating the compression ratio
> - for each supported compressed format on realtime interface.
> - The string is composed of one or more of
> - <fourcc code>/<vendor code>/<modifier>/<compression ratio>
> - separated with spaces.
> -- qcom,dpu-comp-ratio-nrt: A string entry indicating the compression ratio
> - for each supported compressed format on non-realtime interface.
> - The string is composed of one or more of
> - <fourcc code>/<vendor code>/<modifier>/<compression ratio>
> - separated with spaces.
> -- qcom,dpu-undersized-prefill-lines: A u32 value indicates the size of undersized prefill in lines.
> -- qcom,dpu-xtra-prefill-lines: A u32 value indicates the extra prefill in lines.
> -- qcom,dpu-dest-scale-prefill-lines: A u32 value indicates the latency of destination scaler in lines.
> -- qcom,dpu-macrotile-prefill-lines: A u32 value indicates the latency of macrotile in lines.
> -- qcom,dpu-yuv-nv12-prefill-lines: A u32 value indicates the latency of yuv/nv12 in lines.
> -- qcom,dpu-linear-prefill-lines: A u32 value indicates the latency of linear in lines.
> -- qcom,dpu-downscaling-prefill-lines: A u32 value indicates the latency of downscaling in lines.
> -- qcom,dpu-max-per-pipe-bw-kbps: Array of u32 value indicates the max per pipe bandwidth in Kbps.
> -- qcom,dpu-amortizable-threshold: This value indicates the min for traffic shaping in lines.
> -- qcom,dpu-vbif-qos-rt-remap: This array is used to program vbif qos remapper register
> - priority for realtime clients.
> -- qcom,dpu-vbif-qos-nrt-remap: This array is used to program vbif qos remapper register
> - priority for non-realtime clients.
> -- qcom,dpu-danger-lut: A 4 cell property, with a format of <linear,
> - tile, nrt, cwb>,
> - indicating the danger luts on sspp.
> -- qcom,dpu-safe-lut: A 4 cell property, with a format of <linear,
> - tile, nrt, cwb>,
> - indicating the safe luts on sspp.
> -- qcom,dpu-qos-lut-linear: Array of 3 cell property, with a format of
> - <fill level, lut hi, lut lo> in ascending fill level
> - indicating the qos luts for linear format on sspp.
> - Zero fill level on the last entry identifies the default lut.
> -- qcom,dpu-qos-lut-macrotile: Array of 3 cell property, with a format of
> - <fill level, lut hi, lut lo> in ascending fill level
> - indicating the qos luts for macrotile format on sspp.
> - Zero fill level on the last entry identifies the default lut.
> -- qcom,dpu-qos-lut-nrt: Array of 3 cell property, with a format of
> - <fill level, lut hi, lut lo> in ascending fill level
> - indicating the qos luts for nrt (e.g wfd) on sspp.
> - Zero fill level on the last entry identifies the default lut.
> -- qcom,dpu-qos-lut-cwb: Array of 3 cell property, with a format of
> - <fill level, lut hi, lut lo> in ascending fill level
> - indicating the qos luts for cwb on sspp.
> - Zero fill level on the last entry identifies the default lut.
> -- qcom,dpu-cdp-setting: Array of 2 cell property, with a format of
> - <read enable, write enable> for cdp use cases in
> - order of <real_time>, and <non_real_time>.
> -- qcom,dpu-inline-rot-xin: An integer array of xin-ids related to inline
> - rotation.
> -- qcom,dpu-inline-rot-xin-type: A string array indicating the type of xin,
> - namely sspp or wb. Number of entries should match
> - the number of xin-ids defined in
> - property: qcom,dpu-inline-rot-xin
> -- qcom,dpu-inline-rot-clk-ctrl: Array of offsets describing clk control
> - offsets for dynamic clock gating. 1st value
> - in the array represents offset of the control
> - register. 2nd value represents bit offset within
> - control register. Number of offsets defined should
> - match the number of xin-ids defined in
> - property: qcom,dpu-inline-rot-xin
>
> Bus Scaling Subnodes:
> - qcom,dpu-reg-bus: Property to provide Bus scaling for register access for
> @@ -447,223 +127,13 @@ Example:
> #interrupt-cells = <1>;
> iommus = <&mdp_smmu 0>;
>
> - qcom,dpu-off = <0x1000>;
> - qcom,dpu-ctl-off = <0x00002000 0x00002200 0x00002400
> - 0x00002600 0x00002800>;
> - qcom,dpu-mixer-off = <0x00045000 0x00046000
> - 0x00047000 0x0004a000>;
> - qcom,dpu-dspp-top-off = <0x1300>;
> - qcom,dpu-dspp-off = <0x00055000 0x00057000>;
> - qcom,dpu-dspp-ad-off = <0x24000 0x22800>;
> - qcom,dpu-dspp-ad-version = <0x00030000>;
> - qcom,dpu-dest-scaler-top-off = <0x00061000>;
> - qcom,dpu-dest-scaler-off = <0x800 0x1000>;
> - qcom,dpu-wb-off = <0x00066000>;
> - qcom,dpu-wb-xin-id = <6>;
> - qcom,dpu-intf-off = <0x0006b000 0x0006b800
> - 0x0006c000 0x0006c800>;
> - qcom,dpu-intf-type = "none", "dsi", "dsi", "hdmi";
> - qcom,dpu-pp-off = <0x00071000 0x00071800
> - 0x00072000 0x00072800>;
> - qcom,dpu-pp-slave = <0x0 0x0 0x0 0x0>;
> - qcom,dpu-cdm-off = <0x0007a200>;
> - qcom,dpu-dsc-off = <0x00081000 0x00081400>;
> - qcom,dpu-intf-max-prefetch-lines = <0x15 0x15 0x15 0x15>;
> -
> - qcom,dpu-mixer-pair-mask = <2 1 6 0 0 3>;
> - qcom,dpu-mixer-blend-op-off = <0x20 0x38 0x50 0x68 0x80 0x98
> - 0xb0 0xc8 0xe0 0xf8 0x110>;
> -
> -
> - qcom,dpu-sspp-type = "vig", "vig", "vig",
> - "vig", "rgb", "rgb",
> - "rgb", "rgb", "dma",
> - "dma", "cursor", "cursor";
> -
> - qcom,dpu-sspp-off = <0x00005000 0x00007000 0x00009000
> - 0x0000b000 0x00015000 0x00017000
> - 0x00019000 0x0001b000 0x00025000
> - 0x00027000 0x00035000 0x00037000>;
> -
> - qcom,dpu-sspp-xin-id = <0 4 8
> - 12 1 5
> - 9 13 2
> - 10 7 7>;
> -
> - /* offsets are relative to "mdp_phys + qcom,dpu-off */
> - qcom,dpu-sspp-clk-ctrl = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>,
> - <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>,
> - <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>,
> - <0x3b0 16>;
> - qcom,dpu-sspp-clk-status = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>,
> - <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>,
> - <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>,
> - <0x3b0 16>;
> - qcom,dpu-mixer-linewidth = <2560>;
> - qcom,dpu-sspp-linewidth = <2560>;
> - qcom,dpu-mixer-blendstages = <0x7>;
> - qcom,dpu-highest-bank-bit = <0x2>;
> - qcom,dpu-ubwc-version = <0x100>;
> - qcom,dpu-ubwc-static = <0x100>;
> - qcom,dpu-ubwc-swizzle = <0>;
> - qcom,dpu-panic-per-pipe;
> - qcom,dpu-has-src-split;
> - qcom,dpu-has-dim-layer;
> - qcom,dpu-sspp-src-size = <0x100>;
> - qcom,dpu-mixer-size = <0x100>;
> - qcom,dpu-ctl-size = <0x100>;
> - qcom,dpu-dspp-top-size = <0xc>;
> - qcom,dpu-dspp-size = <0x100>;
> - qcom,dpu-intf-size = <0x100>;
> - qcom,dpu-dsc-size = <0x100>;
> - qcom,dpu-cdm-size = <0x100>;
> - qcom,dpu-pp-size = <0x100>;
> - qcom,dpu-wb-size = <0x100>;
> - qcom,dpu-dest-scaler-top-size = <0xc>;
> - qcom,dpu-dest-scaler-size = <0x800>;
> - qcom,dpu-len = <0x100>;
> - qcom,dpu-wb-linewidth = <2560>;
> - qcom,dpu-sspp-scale-size = <0x100>;
> - qcom,dpu-mixer-blendstages = <0x8>;
> - qcom,dpu-qseed-type = "qseedv2";
> - qcom,dpu-csc-type = "csc-10bit";
> - qcom,dpu-highest-bank-bit = <15>;
> - qcom,dpu-has-mixer-gc;
> - qcom,dpu-has-idle-pc;
> - qcom,dpu-has-dest-scaler;
> - qcom,dpu-max-dest-scaler-input-linewidth = <2048>;
> - qcom,dpu-max-dest-scaler-output-linewidth = <2560>;
> - qcom,dpu-sspp-max-rects = <1 1 1 1
> - 1 1 1 1
> - 1 1
> - 1 1>;
> - qcom,dpu-sspp-excl-rect = <1 1 1 1
> - 1 1 1 1
> - 1 1
> - 1 1>;
> - qcom,dpu-sspp-smart-dma-priority = <0 0 0 0
> - 0 0 0 0
> - 0 0
> - 1 2>;
> - qcom,dpu-smart-dma-rev = "smart_dma_v2";
> - qcom,dpu-te-off = <0x100>;
> - qcom,dpu-te2-off = <0x100>;
> - qcom,dpu-te-size = <0xffff>;
> - qcom,dpu-te2-size = <0xffff>;
> -
> - qcom,dpu-wb-id = <2>;
> - qcom,dpu-wb-clk-ctrl = <0x2bc 16>;
> -
> - qcom,dpu-danger-lut = <0x0000000f 0x0000ffff 0x00000000
> - 0x00000000>;
> - qcom,dpu-safe-lut = <0xfffc 0xff00 0xffff 0xffff>;
> - qcom,dpu-qos-lut-linear =
> - <4 0x00000000 0x00000357>,
> - <5 0x00000000 0x00003357>,
> - <6 0x00000000 0x00023357>,
> - <7 0x00000000 0x00223357>,
> - <8 0x00000000 0x02223357>,
> - <9 0x00000000 0x22223357>,
> - <10 0x00000002 0x22223357>,
> - <11 0x00000022 0x22223357>,
> - <12 0x00000222 0x22223357>,
> - <13 0x00002222 0x22223357>,
> - <14 0x00012222 0x22223357>,
> - <0 0x00112222 0x22223357>;
> - qcom,dpu-qos-lut-macrotile =
> - <10 0x00000003 0x44556677>,
> - <11 0x00000033 0x44556677>,
> - <12 0x00000233 0x44556677>,
> - <13 0x00002233 0x44556677>,
> - <14 0x00012233 0x44556677>,
> - <0 0x00112233 0x44556677>;
> - qcom,dpu-qos-lut-nrt =
> - <0 0x00000000 0x00000000>;
> - qcom,dpu-qos-lut-cwb =
> - <0 0x75300000 0x00000000>;
> -
> - qcom,dpu-cdp-setting = <1 1>, <1 0>;
> -
> - qcom,dpu-vbif-off = <0 0>;
> - qcom,dpu-vbif-id = <0 1>;
> - qcom,dpu-vbif-default-ot-rd-limit = <32>;
> - qcom,dpu-vbif-default-ot-wr-limit = <16>;
> - qcom,dpu-vbif-dynamic-ot-rd-limit = <62208000 2>,
> - <124416000 4>, <248832000 16>;
> - qcom,dpu-vbif-dynamic-ot-wr-limit = <62208000 2>,
> - <124416000 4>, <248832000 16>;
> - qcom,dpu-vbif-memtype-0 = <3 3 3 3 3 3 3 3>;
> - qcom,dpu-vbif-memtype-1 = <3 3 3 3 3 3>;
> -
> qcom,dpu-dram-channels = <2>;
> qcom,dpu-num-nrt-paths = <1>;
>
> - qcom,dpu-max-bw-high-kbps = <9000000>;
> - qcom,dpu-max-bw-low-kbps = <9000000>;
> -
> - qcom,dpu-core-ib-ff = "1.1";
> - qcom,dpu-core-clk-ff = "1.0";
> - qcom,dpu-min-core-ib-kbps = <2400000>;
> - qcom,dpu-min-llcc-ib-kbps = <800000>;
> - qcom,dpu-min-dram-ib-kbps = <800000>;
> - qcom,dpu-comp-ratio-rt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3";
> - qcom,dpu-comp-ratio-nrt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3";
> - qcom,dpu-undersized-prefill-lines = <4>;
> - qcom,dpu-xtra-prefill-lines = <5>;
> - qcom,dpu-dest-scale-prefill-lines = <6>;
> - qcom,dpu-macrotile-prefill-lines = <7>;
> - qcom,dpu-yuv-nv12-prefill-lines = <8>;
> - qcom,dpu-linear-prefill-lines = <9>;
> - qcom,dpu-downscaling-prefill-lines = <10>;
> - qcom,dpu-max-per-pipe-bw-kbps = <2400000 2400000 2400000 2400000
> - 2400000 2400000 2400000 2400000>;
> - qcom,dpu-amortizable-threshold = <11>;
> -
> - qcom,dpu-vbif-qos-rt-remap = <3 3 4 4 5 5 6 6>;
> - qcom,dpu-vbif-qos-nrt-remap = <3 3 3 3 3 3 3 3>;
> -
> - qcom,dpu-sspp-vig-blocks {
> - qcom,dpu-vig-csc-off = <0x320>;
> - qcom,dpu-vig-qseed-off = <0x200>;
> - qcom,dpu-vig-qseed-size = <0x74>;
> - /* Offset from vig top, version of HSIC */
> - qcom,dpu-vig-hsic = <0x200 0x00010000>;
> - qcom,dpu-vig-memcolor = <0x200 0x00010000>;
> - qcom,dpu-vig-pcc = <0x1780 0x00010000>;
> - };
> -
> - qcom,dpu-sspp-rgb-blocks {
> - qcom,dpu-rgb-scaler-off = <0x200>;
> - qcom,dpu-rgb-scaler-size = <0x74>;
> - qcom,dpu-rgb-pcc = <0x380 0x00010000>;
> - };
> -
> - qcom,dpu-dspp-blocks {
> - qcom,dpu-dspp-igc = <0x0 0x00010000>;
> - qcom,dpu-dspp-pcc = <0x1700 0x00010000>;
> - qcom,dpu-dspp-gc = <0x17c0 0x00010000>;
> - qcom,dpu-dspp-hsic = <0x0 0x00010000>;
> - qcom,dpu-dspp-memcolor = <0x0 0x00010000>;
> - qcom,dpu-dspp-sixzone = <0x0 0x00010000>;
> - qcom,dpu-dspp-gamut = <0x1600 0x00010000>;
> - qcom,dpu-dspp-dither = <0x0 0x00010000>;
> - qcom,dpu-dspp-hist = <0x0 0x00010000>;
> - qcom,dpu-dspp-vlut = <0x0 0x00010000>;
> - };
> -
> - qcom,dpu-mixer-blocks {
> - qcom,dpu-mixer-gc = <0x3c0 0x00010000>;
> - };
> -
> qcom,msm-hdmi-audio-rx {
> compatible = "qcom,msm-hdmi-audio-codec-rx";
> };
>
> - qcom,dpu-inline-rotator = <&mdss_rotator 0>;
> - qcom,dpu-inline-rot-xin = <10 11>;
> - qcom,dpu-inline-rot-xin-type = "sspp", "wb";
> - qcom,dpu-inline-rot-clk-ctrl = <0x2bc 0x8>, <0x2bc 0xc>;
> -
> qcom,platform-supply-entries {
> #address-cells = <1>;
> #size-cells = <0>;
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
--
Sean Paul, Software Engineer, Google / Chromium OS
More information about the dri-devel
mailing list